EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN2208K1042BBTF

Description
RESISTOR, THIN FILM, 0.75 W, 0.1 %, 100 ppm, 10400 ohm, SURFACE MOUNT, 2208, CHIP
CategoryPassive components    The resistor   
File Size117KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

PTN2208K1042BBTF Overview

RESISTOR, THIN FILM, 0.75 W, 0.1 %, 100 ppm, 10400 ohm, SURFACE MOUNT, 2208, CHIP

PTN2208K1042BBTF Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerVishay
package instructionSMT, 2208
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresANTI-SULFUR; LASER TRIMMABLE; NON-INDUCTIVE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.838 mm
Package length5.309 mm
Package formSMT
Package width2.489 mm
method of packingTR
Rated power dissipation(P)0.75 W
Rated temperature70 °C
resistance10400 Ω
Resistor typeFIXED RESISTOR
size code2208
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage150 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Pb-free
Moisture resistant
Available
High purity alumina substrate
RoHS*
Non-standard values available
COMPLIANT
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic H of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
coating
Nickel barrier
High Purity
Alumina Substrate
Adhesion layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 25 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE - (Ω)
20 - 35K
20 - 65K
20 - 130K
10 - 80K
10 - 301K
10 - 301K
50 - 600K
10 - 1M
10 - 1M
10 - 1.75M
10 - 2M
10 - 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 23-Jan-09
For technical questions, contact: thin-film@vishay.com
www.vishay.com
55
2015 eSports Tournament List
If anyone knows what the list is, please send me one....
勾勾手爱恋 Electronics Design Contest
When the FSMC of STM32 is connected to an external 16-bit Nand, is the output address or command 16 bits?
When the FSMC of STM32F103VC is connected to an external 16-bit Nand, should the address or command written by the CPU to the Address section or Command section be 16 bits or 8 bits? Is the actual out...
dld2 stm32/stm8
What is the function of serpentine routing on FPC board?
Any trace on the FPC will cause delay to the signal when passing a high-frequency signal. The main function of the serpentine trace is to compensate for the smaller delay parts of the "same group of r...
方学放 PCB Design
Please advise on reading and writing USB host computer
I have a USB device, but I don't know the port. How can I read and write data? I use createfile, writefile, and readfile to open the USB device. There is no port in the USB path. The handle is opened ...
672192076 Embedded System
[FPGA (cyclone4) second issue] Timing and simulation learning - pipeline LUT multiplier
[color=#000][font=Tahoma][size=3]Pipeline operation can be said to be the privilege of Verilog HDL language. It is difficult to implement pipeline operation in sequential operation such as C language....
wsdymg FPGA/CPLD
The galaxy pad is disassembled and disassembled [many pictures kill cats]
[i=s]This post was last edited by ljj3166 on 2015-1-7 22:17[/i] [b][size=4]There don't seem to be many posts about disassembly in the forum. I'm going to post one today. Actually, I've been a wrecker ...
ljj3166 Mobile and portable

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 268  1621  2133  2678  870  6  33  43  54  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号