February 2005
®
AS7C33256PFD18B
3.3V 256K
×
18 pipeline burst synchronous SRAM
Features
•
•
•
•
•
•
•
•
Organization: 262,144 words × 18 bits
Fast clock speeds to 200 MHz
Fast clock to data access: 3.0/3.5/4.0 ns
Fast OE access time: 3.0/3.5/4.0 ns
Fully synchronous register-to-register operation
Double-cycle deselect
Asynchronous output enable control
Available in 100-pin TQFP package
•
•
•
•
•
•
•
Individual byte write and global write
Multiple chip enables for easy expansion
Linear or interleaved burst control
Snooze mode for reduced power-standby
Common data inputs and data outputs
3.3V core power supply
2.5V or 3.3V I/O operation with separate V
DDQ
Logic block diagram
LBO
CLK
ADV
ADSC
ADSP
A[17:0]
CLK
CS
CLR
Burst logic
18
16
18
18
18
Q
D
Address
CS
register
CLK
256K × 18
Memory
array
18
GWE
BW
b
BWE
BW
a
CE0
CE1
CE2
D
DQb
Q
CLK
D
DQa
Q
CLK
D
Byte Write
registers
Byte Write
registers
Enable
register
Q
OE
2
Input
registers
CLK
CE
CLK
ZZ
Output
registers
CLK
Power
down
D
Enable
Q
delay
register
CLK
OE
18
DQ [a,b]
Selection guide
–200
Minimum cycle time
Maximum clock frequency
Maximum clock access time
Maximum operating current
Maximum standby current
Maximum CMOS standby current (DC)
5
200
3.0
375
130
30
–166
6
166
3.5
350
100
30
–133
7.5
133
4
325
90
30
Units
ns
MHz
ns
mA
mA
mA
1/31/05; v.1.2
Alliance Semiconductor
P. 1 of 19
Copyright © Alliance Semiconductor. All rights reserved.
AS7C33256PFD18B
®
4 Mb Synchronous SRAM products list
1,2
Org
256KX18
128KX32
128KX36
256KX18
128KX32
128KX36
256KX18
128KX32
128KX36
256KX18
128KX32
128KX36
256KX18
128KX32
128KX36
Part Number
AS7C33256PFS18B
AS7C33128PFS32B
AS7C33128PFS36B
AS7C33256PFD18B
AS7C33128PFD32B
AS7C33128PFD36B
AS7C33256FT18B
AS7C33128FT32B
AS7C33128FT36B
AS7C33256NTD18B
AS7C33128NTD32B
AS7C33128NTD36B
AS7C33256NTF18B
AS7C33128NTF32B
AS7C33128NTF36B
Mode
PL-SCD
PL-SCD
PL-SCD
PL-DCD
PL-DCD
PL-DCD
FT
FT
FT
NTD-PL
NTD-PL
NTD-PL
NTD-FT
NTD-FT
NTD-FT
Speed
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
6.5/7.5/8.0/10 ns
6.5/7.5/8.0/10 ns
6.5/7.5/8.0/10 ns
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
6.5/7.5/8.0/10 ns
6.5/7.5/8.0/10 ns
6.5/7.5/8.0/10 ns
1 Core Power Supply: VDD = 3.3V + 0.165V
2 I/O Supply Voltage: VDDQ = 3.3V + 0.165V for 3.3V I/O
VDDQ = 2.5V + 0.125V for 2.5V I/O
PL-SCD
PL-DCD
FT
NTD
1
-PL
NTD-FT
:
:
:
:
:
Pipelined Burst Synchronous SRAM - Single Cycle Deselect
Pipelined Burst Synchronous SRAM - Double Cycle Deselect
Flow-through Burst Synchronous SRAM
Pipelined Burst Synchronous SRAM with NTD
TM
Flow-through Burst Synchronous SRAM with NTD
TM
1. NTD: No Turnaround Delay. NTD
TM
is a trademark of Alliance Semiconductor Corporation. All trademarks mentioned in this document are the property
of their respective owners.
1/31/05; v.1.2
Alliance Semiconductor
P. 2 of 19
AS7C33256PFD18B
®
Pin arrangement
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE0
CE1
NC
NC
BWb
BWa
CE2
V
DD
V
SS
CLK
GWE
BWE
OE
ADSC
ADSP
ADV
A
A
1/31/05; v.1.2
LBO
A
A
A
A
A1
A0
NC
NC
V
SS
V
DD
NC
NC
A
A
A
A
A
A
A
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
V
DDQ
V
SSQ
NC
NC
DQb0
DQb1
V
SSQ
V
DDQ
DQb2
DQb3
NC
V
DD
NC
V
SS
DQb4
DQb5
V
DDQ
V
SSQ
DQb6
DQb7
DQpb
NC
V
SSQ
V
DDQ
NC
NC
NC
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
TQFP 14 × 20mm
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A
NC
NC
V
DDQ
V
SSQ
NC
DQpa
DQa7
DQa6
V
SSQ
V
DDQ
DQa5
DQa4
VSS
NC
V
DD
ZZ
DQa3
DQa2
V
DDQ
V
SSQ
DQa1
DQa0
NC
NC
V
SSQ
V
DDQ
NC
NC
NC
Alliance Semiconductor
P. 3 of 19
AS7C33256PFD18B
®
Functional description
The AS7C33256PFD18B is a high performance CMOS 4 Mbit synchronous Static Random Access Memory (SRAM) devices
organized as 262,144 words × 18 bits and incorporate a pipeline for highest frequency on any given technology.
Timing for this device is compatible with existing Pentium
®
synchronous cache specifications. This architecture is suited for
ASIC, DSP, and PowerPC
™1
-based systems in computing, datacom, instrumentation, and telecommunications systems.
Fast cycle times of 5.0/6.0/7.5 ns with clock access times (t
CD
) of 3.0/3.5/4.0 ns enable 200, 166 and 133 MHz bus
frequencies. Three chip enable inputs permit easy memory expansion. Burst operation is initiated in one of two ways: the
controller address strobe (ADSC), or the processor address strobe (ADSP). The burst advance pin (ADV) allows subsequent
internally generated burst addresses.
Read cycles are initiated with ADSP (regardless of WE and ADSC) using the new external address clocked into the on-chip
address register. When ADSP is sampled LOW, the chip enables are sampled active, and the output buffer is enabled with OE.
In a read operation the data accessed by the current address, registered in the address registers by the positive edge of CLK, are
carried to the data-out registers and driven on the output pins on the next positive edge of CLK. ADV is ignored on the clock
edge that samples ADSP asserted but is sampled on all subsequent clock edges. Address is incremented internally for the next
access of the burst when ADV is sampled LOW and both address strobes are HIGH. Burst mode is selectable with the LBO
input. With LBO unconnected or driven HIGH, burst operations use a Pentium
®
count sequence. With LBO driven LOW the
device uses a linear count sequence suitable for PowerPC
™
and many other applications.
Write cycles are performed by disabling the output buffers with OE and asserting a write command. A global write enable
GWE writes all 18 bits regardless of the state of individual BW[a:b] inputs. Alternately, when GWE is HIGH, one or more
bytes may be written by asserting BWE and the appropriate individual byte BWn signal(s).
BWn is ignored on the clock edge that samples ADSP LOW, but is sampled on all subsequent clock edges. Output buffers are
disabled when BWn is sampled LOW (regardless of OE). Data is clocked into the data input register when BWn is sampled
LOW. Address is incremented internally to the next burst address if BWn and ADV are sampled LOW. This device operates in
double-cycle deselect feature during read cycles.
Read or write cycles may also be initiated with ADSC instead of ADSP. The differences between cycles initiated with ADSC
and ADSP are as follows:
• ADSP must be sampled HIGH when ADSC is sampled LOW to initiate a cycle with ADSC.
• WE signals are sampled on the clock edge that samples ADSC LOW (and ADSP HIGH).
• Master chip select CE0 blocks ADSP, but not ADSC.
The AS7C33256PFD18B operates from a 3.3V supply. I/Os use a separate power supply that can operate at 2.5V or 3.3V.
These devices are available in a 100-pin 14×20 mm TQFP package.
TQFP capacitance
Parameter
Input capacitance
I/O capacitance
* Guaranteed not tested
Symbol
C
IN*
C
I/O*
Test conditions
V
IN
= 0V
V
OUT
= 0V
Min
-
-
Max
5
7
Unit
pF
pF
TQFP thermal resistance
Description
Thermal resistance
(junction to ambient)
1
Thermal resistance
(junction to top of case)
1
1 This parameter is sampled
Conditions
1–layer
Test conditions follow standard test methods and
procedures for measuring thermal impedance,
per EIA/JESD51
4–layer
Symbol
θ
JA
θ
JA
θ
JC
Typical
40
22
8
Units
°C/W
°C/W
°C/W
1. PowerPC
™
is a trademark International Business Machines Corporation
1/31/05; v.1.2
Alliance Semiconductor
P. 4 of 19
AS7C33256PFD18B
®
Signal descriptions
Signal
CLK
A,A0,A1
DQ[a,b]
CE0
CE1, CE2
ADSP
ADSC
ADV
GWE
BWE
BW[a,b]
OE
LBO
ZZ
NC
I/O
I
I
I/O
I
I
I
I
I
I
I
I
I
I
I
-
Properties
CLOCK
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
ASYNC
STATIC
ASYNC
-
Description
Clock. All inputs except OE, ZZ, LBO are synchronous to this clock.
Address. Sampled when all chip enables are active and ADSC or ADSP are
asserted.
Data. Driven as output when the chip is enabled and OE is active.
Master chip enable. Sampled on clock edges when ADSP or ADSC is active.
When CE0 is inactive, ADSP is blocked. Refer to the Synchronous Truth Table for
more information.
Synchronous chip enables. Active HIGH and active LOW, respectively. Sampled
on clock edges when ADSC is active or when CE0 and ADSP are active.
Address strobe (processor). Asserted LOW to load a new address or to enter
standby mode.
Address strobe (controller). Asserted LOW to load a new address or to enter
standby mode.
Burst advance. Asserted LOW to continue burst read/write.
Global write enable. Asserted LOW to write all 18 bits. When HIGH, BWE and
BW[a,b] control write enable.
Byte write enable. Asserted LOW with GWE = HIGH to enable effect of BW[a,b]
inputs.
Write enables. Used to control write of individual bytes when GWE = HIGH and
BWE = LOW. If any of BW[a,b] is active with GWE = HIGH and BWE = LOW
the cycle is a write cycle. If all BW[a,b] are inactive, the cycle is a read cycle.
Asynchronous output enable. I/O pins are driven when OE is active and the chip is
in read mode.
Selects Burst mode. When tied to V
DD
or left floating, device follows interleaved
Burst order. When driven Low, device follows linear Burst order.
This signal is
internally pulled High.
Snooze. Places device in low power mode; data is retained. Connect to GND if
unused.
No connect
Snooze Mode
SNOOZE MODE is a low current, power-down mode in which the device is deselected and current is reduced to I
SB2
. The duration of
SNOOZE MODE is dictated by the length of time the ZZ is in a High state.
The ZZ pin is an asynchronous, active high input that causes the device to enter SNOOZE MODE.
When the ZZ pin becomes a logic High, I
SB2
is guaranteed after the time t
ZZI
is met. After entering SNOOZE MODE, all inputs except ZZ
is disabled and all outputs go to High-Z. Any operation pending when entering SNOOZE MODE is not guaranteed to successfully complete.
Therefore, SNOOZE MODE (READ or WRITE) must not be initiated until valid pending operations are completed. Similarly, when exiting
SNOOZE MODE during t
PUS
, only a DESELECT or READ cycle should be given while the SRAM is transitioning out of SNOOZE
MODE.
1/31/05; v.1.2
Alliance Semiconductor
P. 5 of 19
京公网安备 11010802033920号
EEWORLD
