EEWORLDEEWORLDEEWORLD

Part Number

Search

XCTN20015800D

Description
RES NET,THIN FILM,1.58K OHMS,100WV,.5% +/-TOL,-50,50PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size118KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

XCTN20015800D Overview

RES NET,THIN FILM,1.58K OHMS,100WV,.5% +/-TOL,-50,50PPM TC,0303 CASE

XCTN20015800D Parametric

Parameter NameAttribute value
MakerVishay
package instructionSMT, 0303
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Manufacturer's serial numberCTN
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-STD-883
resistance1580 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCTN
size code0303
Temperature Coefficient-50,50 ppm/°C
Tolerance0.5%
Operating Voltage100 V
CTN
Vishay Electro-Films
Nichrome Thin Film, Center Tapped Resistors
CHIP
RESISTORS
FEATURES
Wire bondable
Product may not
be to scale
Center tap feature
Chip size: 0.030 inches square
Resistance range total: 10
Ω
to 1 MΩ
Ratio tolerances to: 0.1 %
Resistor material: Nichrome
Oxidized silicon substrate for good power dissipation
The CTN series is a center tapped nichrome resistor chip
providing excellent stability at 250 mW power levels. The
CTN offers the designer flexibility in use as either a single
value resistor or as two resistors with a center tap feature.
The CTNs six bonding pads allows the user increased layout
flexibility.
The CTNs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The CTNs are 100 % electrically tested and
visually inspected to MIL-STD-883.
APPLICATIONS
The CTN center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power and
tracking between two resistors is critical.
Recommended for Hermetic environment where die is not exposed to moisture.
For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used.
Vishay EFI measures low-value resistors by the four wire Kelvin technique.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.5 %
0.1 %
± 10 ppm/°C
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
PROCESS CODE
CLASS H*
203
202
200
201
*MIL-PRF-38534 inspection criteria
1 MΩ
CLASS K*
263
262
260
261
10
Ω
100
Ω
200
Ω
1 kΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
TCR Tracking Between Halves (R
A
/R
B
)
Center Tap Ratio,
R
A
/R
B
Tolerance
Noise, MIL-STD-202, Method 308, 100
Ω
- 250 kΩ
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
* 20 ppm/°C for
R
< 20
www.vishay.com
76
For technical questions, contact: efi@vishay.com
Document Number: 61024
Revision: 12-Mar-08
± 2 ppm/°C *
1 ± 1 % standard
- 35 dB typ.
± 0.1 %
ΔR/R
- 55 °C to + 125 °C
200 V
10
12
min.
100 V max.
250 mW
Problems with dsp2812 downloading using C2Prog
I have configured it to SCI_A download mode and used the official routine, but it just can't connect. Sector problems occur when using my own program...
nlso Microcontroller MCU
EEWORLD University Hall----Computer Vision (Lu Peng, Beijing University of Posts and Telecommunications)
Computer Vision (Lu Peng, Beijing University of Posts and Telecommunications) : https://training.eeworld.com.cn/course/6142This course is an undergraduate course in the Department of Intelligent Scien...
桂花蒸 Integrated technical exchanges
Why do the 2D lines in the DXF exported from PADS become very thick after opening it in CAD?
[i=s]This post was last edited by elec32156 on 2021-9-16 15:09[/i]Why does the 2D line become very thick after opening the DXF exported from PADS in CAD? As shown in the picture, the line becomes a ve...
elec32156 PCB Design
430 flash
[i=s] This post was last edited by zzbaizhi on 2014-10-9 15:47 [/i] The user manual says that flash is mainly divided into two parts: main memory and information memory. Code and data can be stored in...
zzbaizhi Microcontroller MCU
How do I create grace in ccsv8? I can’t find it, and it’s not in the APP center either.
How do I create grace in ccsv8? I can’t find it, and it’s not in the APP center either....
飒沓辰 Microcontroller MCU
Basic Antenna Concept [English, multiple images]
AntennaAn antenna is a device that transmits and/or receives electromagnetic waves. Electromagnetic waves are often referred to as radio waves. Most antennas are resonant devices, which operate effici...
fly RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 172  1375  2370  2343  2393  4  28  48  49  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号