EEWORLDEEWORLDEEWORLD

Part Number

Search

SC100M680B3S71836

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 100V, 20% +Tol, 20% -Tol, 680uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size66KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SC100M680B3S71836 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 100V, 20% +Tol, 20% -Tol, 680uF, Through Hole Mount, ROHS COMPLIANT

SC100M680B3S71836 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance680 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
ESR32 mΩ
leakage current0.68 mA
Manufacturer's serial numberSC
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)100 V
ripple current1790 mA
surface mountNO
Delta tangent0.07
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
Miniature Size Aluminum
Electrolytic Capacitors
SC
[ For Low Impedance and Low E.S.R
Suitable for Output of Mother Board ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 100V
Rate Capacitance Range : 4.7 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DESCRIPTION
Used in switching regulator applications in com-
puters. Especially for high frequency.
Low impedance and E.S.R., high permissible ripple
current at high frequency and higher operating
temperature (-40°C to +105°C).
High Temperature Load Life at 105°C for 3000
Hours
DC Leakage Current (µA) : I = 0.01 CV(µA) or 3µA Whichever is greater.
( Measurements shall be Made After a 2 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 6.3
10
16
25
35
50
63
80
100
D.F (%) : 15
14
12
10
10
8
8
7
7
For capacitor whose capacitance exceeds 2000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
WV (V)
:
6.3
10
10
8
16
5
25
4
35
4
50
4
63
4
100
4
Impedance : Z - 40°C / Z + 20°C
Load Life : 3000 Hours at 105°C Assured with Full Rated Maximum Ripple Current Applied
Multiplier for Ripple Current
Frequency(Hz)
~4.7µF
5.6~33µF
34~330µF
331~1000µF
1200µF Higher
50
0.30
0.40
0.60
0.65
0.85
120
0.40
0.50
0.70
0.80
0.90
300
0.50
0.60
0.80
0.90
0.95
1K
0.70
0.80
0.90
0.98
0.98
10K 100K
0.80 1.00
0.90 1.00
0.95 1.00
1.00 1.00
1.00 1.00
5 x 11 ~ 10 x 12 : Life = 2000 Hours
10 x 15 or Higher : Life = 3000 Hours
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Temperature(°C)
Factor
65
1.80
85
1.50
105
1.00
Dimensions : mm
Rubber Stand-off
4.0
Rubber End Seal
DIAGRAM OF DIMENSIONS
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
5.0
6.3
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F 0.5
F 0.5
0.4Max.
15Min.
0.6
L
15Min.
5Min.
D 0.5
L
5Min.
D 0.5
7.5
10.0
0.8
0.8
How to use a microcontroller to create a file on an SD card that can be recognized by a PC
I know how to write data to an SD card, but I want to create a file that can be recognized by Windows, such as txt, jpg, etc. I don't know if anyone has done this before, and I hope to give me some ad...
99186329 Embedded System
TI M4 Development Board LM4F232 StellarisWare Software Package Download
I searched on TI's official website, but couldn't find it, so I shared StellarisWare, which a friend gave me, with you all.[[i]This post was last edited by Study_Stellaris on 2011-9-28 20:38[/i]]...
Study_Stellaris Microcontroller MCU
DIY pedal controller based on Hercules (VI): Use of timer
[url=http://www.deyisupport.com/question_answer/microcontrollers/hercules/f/70/t/25317.aspx]http://www.deyisupport.com/quest ... s/f/70/t/25317.aspx[/url] The above is a question I raised. Before we n...
tziang Microcontroller MCU
LCD5110 LCD display based on CH554 development board
After trying to add a dual-color OLED screen display with an I2C interface to the CH554 development board, this time I'd like to introduce a monochrome LCD screen based on the SPI interface, the LCD51...
jennyzhaojie MCU
Urgent! Urgent! Urgent! The clock is inaccurate and I can't find the reason
I use DS1302 as the external clock of 430 but it is always inaccurate.Case 1:The 1302 is an industrial-grade DS1302Nwith a precision of 32768HZ, +/-5PPM, and a load capacitor of 12.5PF.Result: 10 seco...
zeng2730 Microcontroller MCU
Looking for Chinese information on omapl138 (Chuanglong or Hezhongda is best)
I am a newbie to omapl138. I use the original TI board omap l138 lcdk. Since the TI company information is too messy, I hope you can share the omapl138 information for my reference. Thank you very muc...
zhouluopei DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 760  2702  2727  273  2734  16  55  6  56  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号