This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Pressure Sensor Specification:
Properties
Measurement range
Absolute accuracy
Total accuracy
Sensitivity (digital)
Sensitivity (analog)
Repeatability
Nonlinearity
Resolution (ADC)
Resolution (DAC)
Response time
Long term drift
P
RANGE
ACC
P_ABS
ACC
P_TOT
SEN
P
SEN
P_AN
ACC
P_REP
ACC
P_NL
RES
P
RES
P_DAC
t
RESP
ACC
P_DRIFT
per year
-0.3 %FSS
T = 25 °C
T = 0 to 70 °C
Test conditions
Value
min.
-0.1
-4 %FSS
-5 %FSS
±2 %FSS
±2.5 %FSS
7.63*10
-6
kPa/digit
0.05 kPa/V
±0.1 %FSS
±0.1 %FSS
15
11
2.2
±0.5 %FSS
0.3 %FSS
bits
bits
ms
typ.
max.
0.1
4 %FSS
5 %FSS
Unit
kPa
Digital input voltage - low-level
Digital output voltage - high-
level
Digital output voltage - low-level
V
IL
V
OH
V
OL
0.9 * V
DD
0.3 * V
DD
0.1 * V
DD
Absolute Maximum Ratings:
Properties
Input voltage VDD pin
Input voltage control pins
1)
Differential over pressure
Differential burst pressure
Common mode pressure
1)
Control pins
Value
min.
V
DD
V
IN_MAX
P
OVER
P
BURST
P
CM
-0.3
-0.3
max.
6.5
5.5
10
10
2500
Unit
V
V
kPa
kPa
kPa
are SDA and SCL
Temperature Sensor Specification:
Properties
Measurement range
Sensitivity
Resolution (ADC)
T
RANGE
SEN
T
RES
T
Value
min.
0
4.272*10
-3
°C /digit
15
bits
typ.
max.
70
Unit
°C
General Information:
Operating Temperature
Storage Conditions (in original
packaging)
Compensated temperature range
Communication interface
Moisture Sensitivity Level (MSL)
Electrostatic discharge
protection (HBM)
max.
5.25
6.5
1
Unit
V
mA
mA
-25 up to +85 °C
< 40 °C ; < 75 % RH
0 to 70 °C
I
2
C, Analog
1
2 kV
Electrical Properties:
Properties
Operating supply voltage
Current consumption
Output current analog pin
Digital input voltage - high-level
V
DD
I
DD
I
OUT_A
V
IH
0.7 * V
DD
Value
min.
4.75
typ.
5
4
Product Specific Pinning:
Pin
SCL
SDA
GND
VOUT
Pad
1
2
3
4
CHECKED
REVISION
Description
I²C serial clock
I²C serial data
Negative supply volage
Analog output
DATE (YYYY-MM-DD)
GENERAL TOLERANCE
I/O
Input
Input/Output
Supply
Output
PROJECTION
METHOD
NiM
DESCRIPTION
001.000
2019-08-13
DIN ISO 2768-1m
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
WSEN-PDUS Differential Pressure
Sensor
BUSINESS UNIT
ORDER CODE
2513130810001
STATUS
PAGE
eiSos
Valid
2/7
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
VDD
NC
RSVD
RSVD
5
6
7
8
Positive supply voltage
No Connection
Reserved
Reserved
Supply
Certification:
RoHS Approval
REACh Approval
Compliant [ 2011/65/EU&2015/863 ]
Conform or declared [ (EC)1907/2006 ]
CHECKED
REVISION
DATE (YYYY-MM-DD)
GENERAL TOLERANCE
PROJECTION
METHOD
NiM
DESCRIPTION
001.000
2019-08-13
DIN ISO 2768-1m
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
WSEN-PDUS Differential Pressure
Sensor
BUSINESS UNIT
ORDER CODE
2513130810001
STATUS
PAGE
eiSos
Valid
3/7
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Packaging Specification - Tape and Reel: [mm]
P0
E1
K0
P2
T
A
D0
W3
W1
close to center
B
F
D
C
B0
E2
W
Top Cover
Tape
W2
A
D1
A0
P1
T2
T1
detail B
Carrier Tape
Cover Tape
End
High Pressure
Port
Feeding direction
Start
B
Cover Tape
Chip Cavity
Sprocket Hole
Embossment
No Component
min. 160mm
Components
No Component
min. 100mm
Cover Tape
min. 400mm
Tape Type
2a
A0
(mm)
typ.
8,80
B0
(mm)
typ.
14,20
W
(mm)
+0,3/ -0,1
24,00
T
(mm)
ref.
0,35
T1
(mm)
ref.
0,10
T2
(mm)
typ.
8,22
K0
(mm)
typ.
8,00
P0
(mm)
±0,1
4,00
P1
(mm)
±0,1
16,00
P2
(mm)
±0,1
2,00
D0
(mm)
+0,1/ -0,0
1,50
D1
(mm)
min.
1,50
E1
(mm)
±0,1
1,75
E2
(mm)
min.
22,25
F
(mm)
±0,1
11,50
Material
Polystyrene
Qty.
(pcs.)
500
A
(mm)
± 2,0
330,00
B
(mm)
min.
1,50
C
(mm)
min.
12,80
D
(mm)
min.
20,20
N
(mm)
± 2,0
60,00
W1
(mm)
+ 2,0
24,40
W2
(mm)
max.
30,40
W3
(mm)
min.
23,90
N
W3
(mm)
max.
27,40
A
Material
Polystyrene/ Polyurethane
CHECKED
REVISION
DATE (YYYY-MM-DD)
GENERAL TOLERANCE
PROJECTION
METHOD
NiM
001.000
2019-08-13
DIN ISO 2768-1m
165° - 180°
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
DESCRIPTION
WSEN-PDUS Differential Pressure
Sensor
BUSINESS UNIT
ORDER CODE
2513130810001
STATUS
PAGE
Pull-of force
Tape width
24 mm
0,1 N - 1,3 N
eiSos
Valid
4/7
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Classification Reflow Profile for SMT components:
Classification Reflow Soldering Profile:
Profile Feature
Preheat Temperature Min
Preheat Temperature Max
Value
T
s min
150 °C
T
s max
200 °C
t
s
T
L
t
L
T
p
t
p
60 - 120 seconds
3 °C/ second max.
217 °C
60 - 150 seconds
see table below
20 - 30 seconds
6 °C/ second max.
8 minutes max.
T
p
Max. Ramp Up Rate
Max. Ramp Down Rate
T
L
T
s max
t
L
t
p
T
C
–5°C
Preheat Time t
s
from T
s min
to T
s max
Ramp-up Rate (T
L
to T
P
)
Liquidous Temperature
Time t
L
maintained above T
L
Peak package body temperature
Time within 5°C of actual peak temperaure
Ramp-down Rate (T
L
to T
P
)
1)
Temperature
Preheat Area
T
s min
t
S
Time 25°C to peak temperature
1)
In
order to reduce residual stress on the sensor components, the recommended ramp-down temperature slope
should not exceed 3°C/sec.
refer to IPC/ JEDEC J-STD-020E
Package Classification Reflow Temperature:
25
Time 25°C to Peak
Properties
PB-Free Assembly | Package Thickness < 1.6 mm
Volume mm³
<350
260 °C
250 °C
Volume mm³
350-2000
260 °C
250 °C
245 °C
Volume mm³
>2000
260 °C
245 °C
245 °C
Time
PB-Free Assembly | Package Thickness 1.6 mm - 2.5 mm
260 °C
PB-Free Assembly | Package Thickness ≥ 2.5 mm
refer to IPC/ JEDEC J-STD-020E
CHECKED
REVISION
DATE (YYYY-MM-DD)
GENERAL TOLERANCE
PROJECTION
METHOD
NiM
DESCRIPTION
001.000
2019-08-13
DIN ISO 2768-1m
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
WSEN-PDUS Differential Pressure
Sensor
BUSINESS UNIT
ORDER CODE
2513130810001
STATUS
PAGE
eiSos
Valid
5/7
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
京公网安备 11010802033920号
EEWORLD
