CX5Z-A2-B2-C145-9.0D20 datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> CX5Z-A2-B2-C145-9.0D20

CX5Z-A2-B2-C145-9.0D20: DescriptionParallel - Fundamental Quartz Crystal, 9MHz Nom,; CategoryPassive components Crystal/resonator; File Size708KB，1 Pages; ManufacturerCardinal Components; Environmental Compliance

Download Datasheet Parametric View All

CX5Z-A2-B2-C145-9.0D20 Overview

Parallel - Fundamental Quartz Crystal, 9MHz Nom,

CX5Z-A2-B2-C145-9.0D20 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Cardinal Components
Reach Compliance Code	compliant
Other features	AT CUT
Ageing	3 PPM/1ST YEAR
Crystal/Resonator Type	PARALLEL - FUNDAMENTAL
Drive level	50 µW
frequency stability	0.005%
frequency tolerance	100 ppm
load capacitance	20 pF
Installation features	SURFACE MOUNT
Nominal operating frequency	9 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
physical size	7mm x 5mm x 1.4mm
Series resistance	45 Ω
surface mount	YES

Preview

Download Datasheet

View All

36.000~48.0000

Ceramic Surface Mount

CARDINAL COMPONENTS

• Lowest maximum drive level available

• Widest frequency range

• Very tight stabilities

Series CX5

Part Numbering Example: CX5 Z - A1 - B2 - C2 60 - 10.0 D18 - 3

CX5

A1*

OPERATING TEMP.

A0 = -10°C ~ +60°C

A1 = -10°C ~ +70°C

A2 = -40°C ~ +85°C

A3 = -55°C ~ +125°C

10.0

D18

-3

SERIES ADDED FEATURES

CX5

BLANK = BULK PACK

Z = TAPE AND REEL

STABILITY TOLERANCE RESISTANCE FREQUENCY

LOAD CAP.

OVERTONE

BLANK: FUND.

B1 = ±100

SEE CHART

C1 = ±100

D16,18,20,ETC.

-3: 3rd OT

B2 = ± 50

BELOW

C2 = ± 50

DS = SERIES

B3 = ± 30

C3 = ± 30

B4 = ± 10

C4 = ± 10

*NOTE:

The above ABC combinations cover basic specification options. We tailor our crystal specifications

to meet customer requirements. Please contact our sales department if you don’t see exactly what you need.

Specifications:

Frequency Range:

7.3728MHZ~48.000MHZ

CX5

Operating Temperature:

Frequency Stability:

Frequency Tolerance:

(at 25°C)

Load Capacitance:

Resistance:

Standard:

0°C ~ +70°C

-40°C ~ +85°C

Standard

± 50 ppm

Standard

Stabilities from ± 5 ppm available.

Standard

± 50 ppm

Tolerances from ± 10 ppm available.

Parallel or series.

Please specify your required load.

Maximum resistance corresponds to frequency.

See chart below.

Shunt Capacitance: 7 pF Max

Aging: ± 3 ppm first year

Drive Level: 50

µW

Max

Packaging: Tape and Reel (1K per Reel)

Bottom View

Resistance Chart:

All resistances are maximum

values.

EQUIVALENT SERIES RESISTANCE (ESR), MODE OF OPERATION (MODE), AND CUT

Frequency MHz

7.3728~9.0000

9.0000~13.0000

13.000~16.0000

16.000~20.0000

ESR(Ω) Mode/cut

45 Max Fund./AT

40 Max Fund./AT

35 Max

30 Max

Fund./AT

Fund/AT

Frequency MHz

20.000~30.0000

30.000~36.0000

36.000~48.0000

ESR (Ω) Mode/cut

25 Max

Fund/AT

25 Max

Fund/AT

80 Max

3rd OT

1801 Broadway St

Charlottesville, VA 22902

USA

Cardinal Components, Inc.

TEL:

(973)785-1333

E-MAIL: sales@cardinalxtal.com

WEB: http://www.cardinalxtal.com

Recommended Resources

WYJ81 type automatic AC regulated power supply circuit

5V power isolation regulator circuit

Multifunctional electronic controller circuit 02

NEC JC-1404HMN-1 type multi-frequency TTL and VGA large screen color display power supply circuit diagram

High efficiency emergency light power circuit

Single-phase motor capacitor series and parallel three-speed circuit

How do I use these two resistors R3, R4, and R5?: What are the three resistors R3, R4, and R5 used for? How do you calculate the current of an LED lamp?...; 1774315354 DIY/Open Source Hardware

TCP UDP debugging software: I'll send you a few tools. I have no money left. I hope you guys will support me. I found some tools for FPGA wireless tuning on the Internet. I've uploaded the ones that I think are good to use. I ho...; wang668 FPGA/CPLD

The impact of static electricity on operational amplifiers: Recently, I am working on the effect of different acquisition circuits on the acquisition effect, so I use different circuits (same op amp) to achieve it. But the op amps I soldered on always break do...; flander_cx Analog electronics

How to determine the L value in the low-pass filter LC circuit?: 100V is converted to 5V through the current transformer and then sent to AD7606 for AC sampling. How to determine the L value in the low-pass LC filter?eeworldpostqq...; chilezhima Analog electronics

Chinese knockoff phones face heavy fines in Europe, IMEI code costs $2,000: [font=微软雅黑][size=3]If this is true, it may be a good thing. What I want to say here is that although I am poor, I will never buy a fake phone. The reason is very simple. This will only lead to the say...; lopopo Talking

Update your myTI account profile to win a HEPA air purifier: [table=98%] [tr][td=10%][b]Activity method:[/b][/td][td][align=left]Follow the instructions on the road signs to update any basic information in your [color=rgb(17, 119, 136)][url=http://links.mkt102....; qq849682862 TI Technology Forum

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components