3078-702-3107 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> 3078-702-3107

3078-702-3107: DescriptionBoard Connector, 2 Contact(s), 1 Row(s), Male, Straight, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle; CategoryThe connector The connector; File Size153KB，1 Pages; ManufacturerMethode Electronics Inc.

Download Datasheet Parametric View All

3078-702-3107 Overview

Board Connector, 2 Contact(s), 1 Row(s), Male, Straight, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle

3078-702-3107 Parametric

Parameter Name	Attribute value
Maker	Methode Electronics Inc.
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	POLARIZED
Board mount options	PCB EDGE LOCKING HOOK
subject depth	0.45 inch
body length	0.306 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU ON NI
Contact completed and terminated	TIN OVER NICKEL
Contact point gender	FEMALE
Contact material	BRASS
contact mode	RECTANGULAR
Contact resistance	5 mΩ
Contact style	SQ PIN-SKT
DIN compliance	NO
Dielectric withstand voltage	1500VAC V
Filter function	NO
IEC compliance	NO
maximum insertion force	LIF N
Insulation resistance	500000000000 Ω
Insulator color	NATURAL
insulator material	GLASS FILLED POLYESTER
JESD-609 code	e3
MIL compliance	NO
Plug contact pitch	0.156 inch
Plug information	MULTIPLE MATING PARTS AVAILABLE
Mixed contacts	NO
Installation method	STRAIGHT
Installation type	BOARD
Number of connectors	ONE
PCB row number	1
Number of rows loaded	1
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
Options	GENERAL PURPOSE
PCB contact pattern	RECTANGULAR
Plating thickness	20u inch
polarization key	POLARIZED KEY
Rated current (signal)	7 A
Guideline	UL, CSA
reliability	COMMERCIAL
Terminal length	0.165 inch
Terminal pitch	3.96 mm
Termination type	SOLDER
Total number of contacts	2
UL Flammability Code	94V-0
Evacuation force-minimum value	LIF N

Preview

Download Datasheet

View All

.156” (3.96mm)

Through Hole Vertical Mount Connector

3000 SERIES “TERMACON”

PART NUMBER LEGEND

30XX-XXX-XXXX

CONTACT TAIL DIMS (SEE TABLE 2)

CONTACT MATERIAL (SEE NOTE 1)

OPTIONS

2 - HIGH INSERTION FORCE CONTACT

3 - LOW INSERTION FORCE CONTACT

NO. OF POSITONS (SEE TABLE 1)

OPTIONS

WITH LEGS

WITH HOOKS

WITH HOOKS AND LOCKING RAMP

WITH LOCKING RAMP

WITH HOOKS, LOCKING RAMP AND POLARIZING KEY

WITHOUT HOOKS, W/ LOCKING RAMP AND POLARIZING KEY

CONTACT FINISH (SEE NOTE 2)

INSULATOR MATERIAL (SEE NOTE 1)

MATING HEADERS: 3100 SERIES

HOLE

LEG

LOCKING

RAMP

POLARIZING KEY &

LOCKING RAMP

Connector Products

1700 Hicks Road • Rolling Meadows, IL 60008 USA

Telephone: 847.392.3500 • Fax: 847.392.9404

email: mcpsales@methode.com • Web Page: www.methode.com

Recommended Resources

GZDW-02 type DC power cabinet circuit

QT-60-80 tower crane control circuit

Using Darlington amplifier

One to two electronic ballast circuit diagram

Typical circuit of bidirectional transfer switch with self-locking

Suddenly thought of the message mailbox: Suppose there are two tasks task1(); task2();Task1 has a higher priority than task2. The specific examples are as follows:Under normal circumstances, if A puts the received data message into the mailb...; ciniao300 Embedded System

Is it better for the crystal oscillator trace to transition from thick to thin to the chip or to keep it the same width as the chip pins?: As the title says! I hope an expert can give a theoretical answer. Thank you! Is it better to make the crystal trace as thick as possible or to keep it consistent? If it is consistent, it cannot be to...; shenlan0302 PCB Design

USB HID experimental doubts about LPC1343: When I was learning the USB HID experiment of LPC1343, I found that the received data was EP0Buf[0]=0x01, which is the data I sent and received, but EP0Buf[1]=0x81, EP0Buf[2=0x7F, I don't know what th...; wanda216 NXP MCU

What products can planar transformers be used in?: What products can planar transformers be used in?...; c709244459 Discrete Device

[Show samples] + Sharing experience on TI sample application: [i=s]This post was last edited by tagetage on 2015-8-3 14:52[/i] I have been using TI chip companies, mainly using MSP430 MCUs. I have always felt very good about TI chips. The chips have high perform...; tagetage TI Technology Forum

The problem of converting 0~5V to 0~3.3V: The pressure sensor used in the project is a differential signal, and I use an instrument amplifier to convert it into a 0~5V signal. However, the microcontroller is STM32F767, and the AD can only rec...; chenbingjy stm32/stm8

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components