EEWORLDEEWORLDEEWORLD

Part Number

Search

8470LDM0511LEN1M

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 25V, 20% +Tol, 20% -Tol, 47uF
CategoryPassive components    capacitor   
File Size46KB,3 Pages
ManufacturerFenghua (HK) Electronics Ltd.
Download Datasheet Parametric View All

8470LDM0511LEN1M Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 25V, 20% +Tol, 20% -Tol, 47uF

8470LDM0511LEN1M Parametric

Parameter NameAttribute value
MakerFenghua (HK) Electronics Ltd.
package instruction,
Reach Compliance Codeunknown
ECCN codeEAR99
capacitance47 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter5 mm
dielectric materialsALUMINUM (WET)
length11 mm
Manufacturer's serial numberLE(25V)
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Package formRadial
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)25 V
seriesLE(25V)
Terminal pitch2 mm
ALUMINUM ELECTROLYTIC CAPACITOR (CD288H LE)
LE FEATURES
Wide temperature high frequency and ultra low impedance
D 8mm with top safety vent construction
For switching power supplies and other industrial electronic products applications
SPECIFICATIONS
Item
Rated Voltage Range
Operating Temperature
Range
Nominal Capacitance Range
Capacitance Tolerance
Performance Characteristics
6.3V.DC~100V.DC
-40°C~+105°C
0.1 F~10000 F
±20%(M,+25°C,120Hz)
After application of rated voltage for 2 minutes: I 0.01CV or 3 A(Whichever is greater)25°C
Leakage Current
C: Nominal Capacitance in F; V: Rated Working Voltage in V
When capacitance is over 1000 F, tan shall be added 0.02 with increase of every 1000 F
Dissipation Factor
Rated Working Voltage(V)
(tan )
6.3
0.24
10
0.20
16
0.16
6.3~16
5
7
25
0.14
35
0.12
50
0.10
tan ( MAX) (25°C,120Hz)
Rated Working Voltage
25~100
4
3
Temperature Stability
Impedance Ratio
(120Hz)
Z-25°C/Z+20°C
Z-40°C/Z+20°C
After application of rated working voltage and maximum permissible ripple current specified at +105°C for 1000
hours, Capacitors meet the characteristics requirements measured at +25°C listed below:
Load Life
Leakage Current
Less than the initial specified value
Less than 150% of the initial specified value or 0.4
Within ±20% of the initial measured value
Capacitance Change
After Leaving capacitor under no load at +105°C for 500 hours, Capacitors meet the characteristics listed
Shelf Life
above.
MULTIPLIER FOR RIPPLE CURRENT
Frequency coefficient
Freq(Hz)
Cap(uF)
6.3~35
50~63
100~250
350~450
Temperature coefficient
Ambient Temperature(°C)
Factor
+105
1.0
+85
1.7
+65
2.1
1000
1000
50(60)
0.8
0.8
0.8
0.8
0.8
0.8
100(120)
1
1
1
1
1
1
1K
1.1
1.2
1.5
1.2
1.6
1.3
10K
1.2
1.3
1.7
1.3
1.9
1.5
1000
1000
δ
tan
www.fenghua.com
1/3
μ
μ
μ
μ
μ
δ
μ
δ
δ
≥ φ
63
0.09
100
0.08
Is there a 24-bit AD chip with a gain of 256?
Can any experts please tell me if there is a 24-bit AD chip with a maximum gain of 256? Please recommend one. Thank you!...
chenbingjy TI Technology Forum
Protection of the radio receiver when the transmitting and receiving antennas of several people are very close to each other
Author's blog: [url]http://radiobcl.blog.163.com/[/url] Add a limiter circuit to the receiving input behind the transmit/receive switching relay of the FT-80C and other radios: If there are no suitabl...
冰人 RF/Wirelessly
Help burning 2812 flash
I want to know how to burn the flash of 2812. If anyone knows, please give me some advice....
zhaoyunkai Microcontroller MCU
[RTT & Renesas high performance CPK-RA6M4] 5. Software simulation I2C drive OLED evaluation
1. Hardware 1. Pin resources Since pure software simulation is used, there are no special requirements for the pins, so the connection method of the previous evaluation project is still used. [RTTRene...
kit7828 Renesas Electronics MCUs
[Help Post] Is the download link for the RSL10-002GEVB pack on ON Semiconductor's official website wrong?
After installing the IDE downloaded from the ON Semiconductor official website, and installing the pack specified for RSL10-002GEVB on the official website, why is the RSL10-002GEVB board still not di...
yilonglucky onsemi and Avnet IoT Innovation Design Competition
The system stops at FMD::FMD_Init, please help!
: Recently I'm working on the problem of using the remaining FLASH on S3C2410 for permanent storage. My PB is CE4.2. The workflow is as follows. First, put the HIVE reward when planting the kernel, an...
knight0101 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2174  1083  161  18  2104  44  22  4  1  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号