EEWORLDEEWORLDEEWORLD

Part Number

Search

LXY10VB82ME11

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 10V, 20% +Tol, 20% -Tol, 82uF, Through Hole Mount, RADIAL LEADED
CategoryPassive components    capacitor   
File Size93KB,2 Pages
ManufacturerNIPPON CHEMI-CON
Websitehttp://www.chemi-con.co.jp
Download Datasheet Parametric View All

LXY10VB82ME11 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 10V, 20% +Tol, 20% -Tol, 82uF, Through Hole Mount, RADIAL LEADED

LXY10VB82ME11 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerNIPPON CHEMI-CON
package instruction,
Reach Compliance Codeunknown
ECCN codeEAR99
capacitance82 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
JESD-609 codee0
leakage current0.0082 mA
Manufacturer's serial numberLXY
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Package shapeCYLINDRICAL PACKAGE
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)10 V
ripple current163 mA
surface mountNO
Delta tangent0.19
Terminal surfaceTin/Lead (Sn/Pb)
Terminal shapeWIRE
SRM-Series
ALUMINUM ELECTROLYTIC CAPACITORS
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
LXZ
High reliability, Low impedance, 105C
@Newly
innovative electrolyte and internal architecture are employed
@Endurance
with ripple current : 105C 2000 to 8000 hours
@Solvent-proof
type (see PRECAUTIONS AND GUIDELINES)
lower Z
downsized
LXY
?SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
-55 to +105C
10 to 63V
dc
P20%
(M)
I=0.01CV or 3MA, whichever is greater.
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
10V 16V 25V 35V 50V 63V
Rated voltage (V
dc
)
0.19 0.16 0.14 0.12 0.10 0.10
tanE (Max.)
When nominal capacitance exceeds 1000MF, add 0.02 to the value above for each 1000MF increase.
10V
dc
to 50V
dc
: 3max.
Z(-55C)/Z(+20C)
63V
dc
: 6max.
Characteristics
(at 20C, 120Hz)
(at 20C after 2 minutes)
(at 20C, 120Hz)
Shelf Life
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated
ripple current is applied for the specified period of time at 105C.
Time
F5
& 6.3 : 2000hours
F8
: 3000hours
F10
: 5000hours
F12.5
: 7000hours
F16
& 18 : 8000hours
Capacitance change
[P20%
of the initial value
D.F. (tanE)
[200%
of the initial specified value
Leakage current
[The
initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1000 hours at 105C
without voltage applied.
Capacitance change
[P20%
of the initial value
D.F. (tanE)
[200%
of the initial specified value
Leakage current
[The
initial specified value
?DIMENSIONS
(Radial Lead Type=VB) [mm]
FP0.5
FP0.5
Fd
Sleeve
L'
Vent
(except
F6.3
and smaller)
15min.
4min.
(F5 to
F10)
(F12.5 to
F16)
fD
fd
F
fD'
L'
5
0.5
2.0
6.3
0.5
2.5
10 12.5
8
0.6 0.6 0.6
3.5 5.0 5.0
FD+0.5max.
L+1.5max.
16
0.8
7.5
FD'
Gas escape end seal
?PART
NUMBERING SYSTEM
LXY
16
VB
2200
M
K30
Capacitance
4.7MF
10MF
100MF
2200MF
Code
4R7
10
100
2200
Case code
Cap tolerance (P20%)
Nominal cap code
Radial lead type
Rated voltage in volts
Series name
(1/2)
CAT. No. E1001D
DP83822I Industrial Ethernet PHY auto-negotiation function and its strap resistor configuration
[i=s]This post was last edited by qwqwqw2088 on 2019-11-1 11:44[/i]In factory automation applications, due to the increasing number of on-site device nodes and the increasing requirements for automati...
qwqwqw2088 Analogue and Mixed Signal
Basic books about Verilog, everyone can take a look
[[i] This post was last edited by zhangkai0215 on 2009-5-20 09:06[/i]]...
zhangkai0215 FPGA/CPLD
SPI bus transmission distance problem
I am currently working on my graduation project, which requires a transmission distance of several dozen meters, but the SPI transmission distance is too short. I asked the teacher, and to be honest: ...
feixiaduibing MCU
Questions about UCF
I am using a Xilinx FPGA , and several pins must be fixed values, but there are no related signals in my design . If I don't change the code, can I set these pins to the values I expect in the UCF?...
eeleader-mcu FPGA/CPLD
Has anyone used Renesas chips to operate SD cards? Please give me some advice
Has anyone used Renesas chips to operate SD cards? I use the SD and FATFS libraries of STM32, but it seems that they cannot be used. I still have to write the relevant libraries myself. If you have us...
suoma Renesas Electronics MCUs
Can someone please help me! Regarding the semaphore problem! If a semaphore is only declared without initialization and is directly taken, will it cause the task that calls this semaphore to have an unexpected long-term PEND?
Supplement: In a multi-tasking system, the task that calls this semaphore has the lowest priority (this semaphore is only called in one place and is actually useless). In addition, the waiting time fo...
223xh Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1934  2185  663  2433  2723  39  44  14  49  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号