EEWORLDEEWORLDEEWORLD

Part Number

Search

AS91L1006S10L100C

Description
The AS91L1006BU is a one to 6-port JTAG gateway
File Size241KB,28 Pages
ManufacturerETC
Download Datasheet View All

AS91L1006S10L100C Overview

The AS91L1006BU is a one to 6-port JTAG gateway

July 2004
AS91L1006BU
6-Port JTAG Gateway
Description
The AS91L1006BU is a one to 6-port
JTAG gateway. It partitions a single JTAG chain
into six separate chains. These separate chains
can be optionally configured to operate as a single
chain.
The AS91L1006BU device is used to
provide enhanced capabilities to the standard
IEEE1149.1. It enables the IEEE1149.1 interface
to be used in a true Multi-Drop environment without
any additional signals. This Multi-Drop capability
enables the standard IEEE1149.1 interface to be
used not just for stand alone PCB (Printed Circuit
Board) testing, but also for complete system
testing including all PCBs within a system back
plane environment.
The AS91L1006BU provides the capability
of partitioning the PCB, into multiple smaller
IEEE1149.1 scan chains totally under software
control. Partitioning the IEEE1149.1 chains on the
PCB has several benefits which include easier
fault diagnostics capabilities as a fault on one of
the IEEE1149.1 Local Scan Ports (LSPs) does
not render the PCB untestable, faster flash
programming on the PCBs, and removal of
IEEE1149.1 signal loading issues.
All of the protocols required for
addressing the AS91L1006BU device via the
Multi-Drop capability and the protocols for
configuring which of the six IEEE1149.1 LSPs on
the AS91L1006BU are to be used, is handled via
3
rd
party ATPG tools from vendors like Asset-
Intertech and JTAG Technologies. In a Multi-Drop
environment it is also possible to perform
interconnect tests between multiple PCBs within a
system thus extending the interconnect tests to
the back plane itself.
Key Features
Device Multi-Drop addressable via the IEEE
1149.1 protocol
Support for 6 local scan chains addressable via
the IEEE 1149.1 interface
Support for Pass-Through™
Support for the IEEE 1149.1 USERCODE
instruction
Support for Status instruction enabling non-
intrusive monitoring of the system card
Local Scan Port (LSP) enable signal provides the
ability to use non IEEE 1149.1 compliant devices
that require JTAG enable signal
Provides the ability to initiate Self-Test on a
remote PCB via a standard IEEE 1149.1
command
Support for JTAG Technologies AutoWR™
feature
Pinout and feature set compatible (complete
second source) with the Firecron JTS06BU
device
Available in a 100-pin LQFP or a 100-pin
FPBGA lead free package
Device Block Diagram
P a s s T h r o u g h E n a b le
P r im a r y 1 1 4 9 . 1
J T A G In te rfa c e
LSP1
S ta tu s D a ta
LSP2
U s e rc o d e
D a ta
1 1 4 9 . 1 T A P C o n t r o lle r
and
B o u n d a r y R e g is t e r S e le c t io n L o g ic
D e v ic e
a d d re s s
P a s s T h ro u g h
L o g ic & L o c a l
S c a n P o rt
C o n n e c t io n /
C o n f ig
lo g ic
LSP3
LSP4
D e v ic e
S e le c t io n
L o g ic
L o c a l S c a n P o rt
P a r k /U n -p a rk
S y n c L o g ic
LSP5
LSP6
Figure 1 - AS91L1006BU Device Block Diagram
Alliance Semiconductor
2575 Augustine Drive
Santa Clara, CA 95054
T: 408-855-4900
F: 408-855-4999
www.alsc.com
Has anyone used the C2000 PWM-chopper?
The article says: The PWM-chopper submodule allows a high-frequency carrier signal to modulate the PWM waveform generated by the action-qualifier and dead-band submodules. This capability is important...
dontium Microcontroller MCU
C6455DMA channel problem
When configuring PaRAM mapping and queue assignment, is the DMA channel selected randomly? I read the data sheet and it also assigns each channel to each event....
215Mr黎子 DSP and ARM Processors
Design of portable blood pressure monitor based on MSP430 microcontroller and USB bus
At present, most of the sphygmomanometers on the market are still mercury sphygmomanometers. Electronic sphygmomanometers have been widely popularized abroad, but they have just begun to be used in my...
dtcxn Medical Electronics
M4's experience with static library files when writing uc/GUI
When using programs like uc/GUI that contain many C files, many of the C files generally do not need to be modified. Therefore, in order to facilitate compilation, the compiler is generally used to ge...
anananjjj Microcontroller MCU
Design of digital controlled DC current source controlled by MSP430 single chip microcomputer
[p=null, 2, left][color=rgb(51, 51, 51)][font=宋体][size=12pt]This system is a digital control DC current source system based on a single chip microcomputer. Using a single chip microcomputer as the cor...
Jacktang Microcontroller MCU
Ask about the serial port driver
After the hardware flow control is set, when RTS is enabled and data can be sent, is the CTS signal valid? Is it implemented by the driver or automatically enabled by the hardware? If it is the driver...
suizhihen Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2683  413  227  705  2730  55  9  5  15  28 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号