This datasheet describes the electrical characteristics, switching characteristics, configuration specifications, and I/O timing for Arria
®
10 devices.
Arria 10 devices are offered in extended and industrial grades. Extended devices are offered in –E1 (fastest), –E2, and –E3 speed grades. Industrial
grade devices are offered in the –I1, –I2, and –I3 speed grades.
The suffix after the speed grade denotes the power options offered in Arria 10 devices.
•
•
•
•
L—Low static power
S—Standard power
M—Enabled with the V
CC
PowerManager feature (you can power V
CC
and V
CCP
at nominal voltage of 0.90 V or lower voltage of 0.83 V)
V—Supported with the SmartVID feature (lowest static power)
Related Information
Arria 10 Device Overview
Provides more information about the densities and packages of devices in the Arria 10 family.
Electrical Characteristics
The following sections describe the operating conditions and power consumption of Arria 10 devices.
Operating Conditions
Arria 10 devices are rated according to a set of defined parameters. To maintain the highest possible performance and reliability of the Arria 10
devices, you must consider the operating requirements described in this section.
and Trademark Office and in other countries. All other words and logos identified as trademarks or service marks are the property of their respective holders as described at
www.altera.com/common/legal.html.
Altera
warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without
notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are
advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services.
2015 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, ENPIRION, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words and logos are trademarks of Altera Corporation and registered in the U.S. Patent
ISO
9001:2008
Registered
www.altera.com
101 Innovation Drive, San Jose, CA 95134
2
Absolute Maximum Ratings
A10-DATASHEET
2015.12.31
Absolute Maximum Ratings
This section defines the maximum operating conditions for Arria 10 devices. The values are based on experiments conducted with the devices and
theoretical modeling of breakdown and damage mechanisms. The functional operation of the device is not implied for these conditions.
Caution:
Conditions outside the range listed in the following table may cause permanent damage to the device. Additionally, device operation at
the absolute maximum ratings for extended periods of time may have adverse effects on the device.
Table 1: Absolute Maximum Ratings for Arria 10 Devices—Preliminary
Symbol
Description
Condition
Minimum
Maximum
Unit
V
CC
V
CCP
V
CCERAM
V
CCPT
V
CCBAT
V
CCPGM
V
CCIO
V
CCA_PLL
V
CCT_GXB
V
CCR_GXB
V
CCH_GXB
V
CCL_HPS
V
CCIO_HPS
(1)
Core voltage power supply
Periphery circuitry and transceiver fabric interface power
supply
Embedded memory power supply
Power supply for programmable power technology and I/O
pre-driver
Battery back-up power supply for design security volatile key
register
Configuration pins power supply
I/O buffers power supply
Phase-locked loop (PLL) analog power supply
Transmitter power
Receiver power
Transmitter output buffer power
HPS core voltage and periphery circuitry power supply
HPS I/O buffers power supply
—
—
—
—
—
(1)
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
1.21
1.21
1.36
2.46
2.46
2.46
4.10
2.46
2.46
1.34
1.34
2.46
1.27
4.10
2.46
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
3 V I/O
LVDS I/O
—
—
—
—
—
3 V I/O
LVDS I/O
The LVDS I/O values are applicable to all dedicated and dual-function configuration I/Os.
Arria 10 Device Datasheet
Send Feedback
Altera Corporation
A10-DATASHEET
2015.12.31
Maximum Allowed Overshoot and Undershoot Voltage
3
Symbol
Description
Condition
Minimum
Maximum
Unit
V
CCIOREF_HPS
V
CCPLL_HPS
I
OUT
T
J
T
STG
HPS I/O pre-driver power supply
HPS PLL power supply
DC output current per pin
Operating junction temperature
Storage temperature (no bias)
—
—
—
—
—
–0.50
–0.50
–25
–55
–65
2.46
2.46
25
125
150
V
V
mA
°C
°C
Maximum Allowed Overshoot and Undershoot Voltage
During transitions, input signals may overshoot to the voltage listed in the following table and undershoot to –2.0 V for input currents less than
100 mA and periods shorter than 20 ns.
The maximum allowed overshoot duration is specified as a percentage of high time over the lifetime of the device. A DC signal is equivalent to
100% duty cycle.
For example, a signal that overshoots to 2.70 V for LVDS I/O can only be at 2.70 V for ~4% over the lifetime of the device.
Table 2: Maximum Allowed Overshoot During Transitions for Arria 10 Devices—Preliminary
This table lists the maximum allowed input overshoot voltage and the duration of the overshoot voltage as a percentage of device lifetime. The LVDS I/O
values are applicable to the
VREFP_ADC
and
VREFN_ADC
I/O pins.
Symbol
Description
Condition (V)
LVDS I/O
(2)
3 V I/O
Overshoot Duration as % at T
J
= 100°C
Unit
2.50
2.55
Vi (AC)
AC input voltage
2.60
2.65
2.70
> 2.70
3.80
3.85
3.90
3.95
4.00
> 4.00
100
42
18
9
4
No overshoot allowed
%
%
%
%
%
%
(2)
The LVDS I/O values are applicable to all dedicated and dual-function configuration I/Os.
Altera Corporation
Arria 10 Device Datasheet
Send Feedback
4
Recommended Operating Conditions
A10-DATASHEET
2015.12.31
Recommended Operating Conditions
This section lists the functional operation limits for the AC and DC parameters for Arria 10 devices.
Recommended Operating Conditions
Table 3: Recommended Operating Conditions for Arria 10 Devices—Preliminary
This table lists the steady-state voltage values expected from Arria 10 devices. Power supply ramps must all be strictly monotonic, without plateaus.
Symbol
Description
Condition
Minimum
(3)
Typical
Maximum
(3)
Unit
Standard and low power
V
CC
Core voltage power supply
V
CC
PowerManager
(5)
SmartVID
(6)
V
CCP
Periphery circuitry and transceiver
fabric interface power supply
Standard and low power
V
CC
PowerManager
(5)
SmartVID
(6)
1.8 V
V
CCPGM
V
CCERAM
Configuration pins power supply
Embedded memory power supply
1.5 V
1.2 V
0.9 V
0.87
0.8, 0.87
0.8
0.87
0.8, 0.87
0.8
1.71
1.425
1.14
0.87
0.9
(4)
0.83, 0.9
—
0.9
(4)
0.83, 0.9
—
1.8
1.5
1.2
0.9
(4)
0.93
0.86, 0.93
0.93
0.93
0.86, 0.93
0.93
1.89
1.575
1.26
0.93
V
V
V
V
V
V
V
V
V
V
(3)
(4)
(5)
(6)
This value describes the budget for the DC (static) power supply tolerance and does not include the dynamic tolerance requirements. Refer to the
PDN tool for the additional budget for the dynamic tolerance requirements.
You can operate –1 and –2 speed grade devices at 0.9 V or 0.95 V typical value. You can operate -3 speed grade device at only 0.9 V typical value.
Core performance shown in this datasheet is applicable for the operation at 0.9 V. Operating at 0.95 V results in higher core performance and higher
power consumption. For more information about the performance and power consumption of 0.95 V operation, refer to the Quartus
®
Prime
software timing reports, PowerPlay Power Analyzer report, and Early Power Estimator (EPE).
You can operate V
CC
PowerManager devices at either 0.83 V or 0.9 V. Power V
CC
and V
CCP
at 0.9 V to achieve –1 speed grade performance. Power
V
CC
and V
CCP
at 0.83 V to achieve lower performance using the lowest power.
SmartVID is supported in devices with –2V and –3V speed grades only.
Arria 10 Device Datasheet
Send Feedback
Altera Corporation
A10-DATASHEET
2015.12.31
Recommended Operating Conditions
5
Symbol
Description
Condition
Minimum
(3)
Typical
Maximum
(3)
Unit
V
CCBAT
V
CCPT
(7)
Battery back-up power supply
(For design security volatile key
register)
Power supply for programmable
power technology and I/O pre-driver
1.8 V
1.2 V
1.8 V
3.0 V (for 3 V I/O only)
2.5 V (for 3 V I/O only)
1.8 V
1.71
1.14
1.71
2.85
2.375
1.71
1.425
(8)
1.8
1.2
1.8
3.0
2.5
1.8
1.5
1.35
1.25
1.2
1.8
1.25
—
—
—
—
—
1.89
1.26
1.89
3.15
2.625
1.89
1.575
(8)
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
°C
°C
V
CCIO
I/O buffers power supply
1.5 V
1.35 V
1.25 V
1.2 V
1.19
(8)
1.31
(8)
V
CCA_PLL
V
REFP_ADC
V
I
(9)
PLL analog voltage regulator power
supply
Precision voltage reference for
voltage sensor
DC input voltage
Output voltage
Operating junction temperature
—
—
3 V I/O
LVDS I/O
—
Extended
Industrial
1.71
1.2475
–0.3
–0.3
0
0
–40
1.89
1.2525
3.3
2.19
V
CCIO
100
100
V
O
T
J
(3)
(7)
(8)
(9)
This value describes the budget for the DC (static) power supply tolerance and does not include the dynamic tolerance requirements. Refer to the
PDN tool for the additional budget for the dynamic tolerance requirements.
If you do not use the design security feature in Arria 10 devices, connect V
CCBAT
to a 1.5-V or 1.8-V power supply. Arria 10 power-on reset (POR)
circuitry monitors V
CCBAT
. Arria 10 devices do not exit POR if V
CCBAT
is not powered up.
For minimum and maximum voltage values, refer to the I/O Standard Specifications section.
The LVDS I/O values are applicable to all dedicated and dual-function configuration I/Os.
I may not be as good as an uneducated electrician in this regard. Is there any way or book I can recommend to learn?[[i]This post was last edited by boofeng2002 on 2012-3-31 11:18[/i]]...
[i=s]This post was last edited by qwqwqw2088 on 2018-4-13 10:38[/i] [size=4]A few days ago, netizen @[color=#333333]chenbingjy asked for help[/color][font="] [/font][font="]how to set the line width o...
Minimizing the output ripple and transients of a switching regulator is important, especially when powering noise-sensitive devices such as high-resolution ADCs, where output ripple will appear as a d...
The project uses launchPAD. This is the COMP_A+ function diagram of GRACE configuration. If it is to be configured as a hysteresis comparator, can resistors be used to build peripheral circuits? How t...
ARM is the industry's leading supplier of microprocessor technology, offering the broadest range of microprocessor cores to meet the performance, power and cost requirements of almost all application ...
I want to learn embedded development recently, but I only know C and C++ and have no foundation in assembly language. Can I learn embedded development directly without learning assembly language?...
While
the solid-state battery
industry is still engaged in a long technological marathon for
the "ultimate solution" for
electric vehicles
, some companies have begun looking for mor...[Details]
introduction
Bluetooth technology is a short-range wireless communication technology designed to replace wired cables. It is a wireless communication technology standard developed by the SIG, ...[Details]
Multi-touch mobile phone
Multi-touch is a system that can respond to multiple touches on the screen at the same time. Multi-touch phones are divided into capacitive and resistive types. Capaci...[Details]
According to foreign media reports, secondary battery materials company POSCO Future M announced that it has successfully developed two experimental (prototype) positive electrode materials for the...[Details]
This paper proposes a temperature real-time transmission and display solution based on LED optical data transmission, with Jingwei Yager low-power FPGA HR (Yellow River) series as the main controll...[Details]
introduction
As “energy conservation and emission reduction” has become an indicator of the National Economic Development Outline of the 11th Five-Year Plan, people’s awareness of green enviro...[Details]
In the scorching summer, electric fans are a must-have for cooling down people's homes. However, I believe most people have encountered this situation: the fan is plugged in, the switch is pressed,...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
Over the past decade, the narrative surrounding fuel vehicles has been one of decline and replacement. Under the onslaught of new energy vehicles, traditional automakers have been forced to acceler...[Details]
There are many motors that can use thyristor speed control, and they can be used in almost all industries. Various types of motors, such as fans, pumps, AC motors, DC motors, torque motors, single-...[Details]
Lightweighting of automobiles is still a relatively unfamiliar term for automobiles. With the continuous improvement of environmental protection requirements, relevant regulations have also put for...[Details]
For self-driving cars, LiDAR is the sensory organ that allows them to "see the road." Simply put, its operating principle involves sending out a laser beam, receiving the echo, and ultimately gener...[Details]
introduction
With the development of the information superhighway and the internet, broadcast television has become increasingly widespread worldwide. Television information has emerged in var...[Details]
Traditionally, electrical energy is transmitted primarily through wires, requiring direct physical contact between the power source and the load. With the increasing number of electrical devices in...[Details]
According to Reuters, citing people familiar with the matter, British semiconductor design company Arm Holdings (NASDAQ:ARM) has hired Rami Sinno, head of Amazon's (NASDAQ:AMZN) artificial intellig...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
