EEWORLDEEWORLDEEWORLD

Part Number

Search

LR1117-ADJ(TO-220)

Description
Regulator, 1 Output, BIPolar,
CategoryPower/power management    The power supply circuit   
File Size251KB,10 Pages
ManufacturerLRC
Websitehttp://www.lrc.cn
Environmental Compliance
Download Datasheet Parametric View All

LR1117-ADJ(TO-220) Overview

Regulator, 1 Output, BIPolar,

LR1117-ADJ(TO-220) Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerLRC
package instruction, SIP3,.1TB
Reach Compliance Codeunknown
AdjustabilityADJUSTABLE
Nominal dropback voltage 11.15 V
Maximum grid regulation rate (%/V)0.031
Maximum load regulation (%)0.4%
Output times1
Number of terminals3
Working temperatureTJ-Max125 °C
Working temperature TJ-Min
Maximum output current 11 A
Maximum output voltage 113.8 V
Minimum output voltage 11.25 V
Package body materialPLASTIC/EPOXY
Encapsulate equivalent codeSIP3,.1TB
Certification statusNot Qualified
surface mountNO
technologyBIPOLAR
Terminal pitch2.54 mm
Terminal locationSINGLE
LRC
LESHAN RADIO COMPANY,LTD.
LOW DROP FIXED AND ADJUSTABLE POSITIVE VOLTAGE REGULATORS
DESCRIPTION
The LRC LR1117/A is a LOW DROP Voltage Regulator
able to provide up to
0.8/1.0A
of Output Current, available
even in adjustable version (Vref=1.25V). Concerning fixed
versions, are offered the following Output Voltages: 1.5V,
1.8V, 2.5V, 2.85V, 3.0V, 3.3V, 3.6V and 5.0V. The 2.85V type
is ideal for SCSI-2 lines active termination. High efficiency
is assured by NPN pass transistor. In fact in the case, unlike
than PNP one, the Quiescent Current flows mostly into the
for stability. On chip trimming allows the regulator to reach a
very tight output voltage tolerance, within ±1% at 25°C. The
ADJUSTABLE LR1117/A is pin to pin compatible with the
other standard Adjustable voltage regulators maintaining the
better performances in terms of Drop and Tolerance.
1
23
TO-220
1
2
1
3
TO-252
32
SOT-223
FEATURES
*Low dropout voltage (1V Typ.)
*2.85V device performances are suitable for SCSI-2 active
termination
*Output current up to
0.8/1.0A
*Fixed output voltage of: 1.5V, 1.8V, 2.5V, 2,85V, 3.0V, 3.3V,
*
3.6V, 5.0V
*Adjustable version availability (Vref=1.25V)
*Internal current and thermal limit
*Available in ±1%(at 25°C) and 2% in all temperature range
*Supply voltage rejection: 75dB (TYP)
*Temperature range: 0°C to 125°C
1: GND
2: Output
3: Input
ABSOLUTE MAXIMUM RATINGS
PARAMETER
DC Input Voltage
Power Dissipation
Storage temperature
Operating Junction Temperature
SYMBOL
V
IN
Ptot
Tstg
Top
VALUE
9 ,
15
UNIT
V
W
C
C
°C/W
12
-65 ~ +150
0 ~ +125
50
Thermal Resistance Junction
ambien
Rthj-amb
Note:
1.
Absolute Maximum Ratings are those value beyond which damage to the device may occur. Functional
operation under there condition is not implied. Over the above suggested Max Power Dissipation a Short Circuit
could definitively damage the device.
2 .Marking=DFXXX=15V; Marking=LRXXX.=15V; Marking=LRXXX=9V.
1/10
Urgent help, about the USART serial communication (sp3232) problem of STM32F407VGT6 chip (please help if you pass by)
Today I would like to ask you a question about the serial port communication of STM32F407 . Actually, this is a very basic question, but I have to ask you.1. Problem descriptionThe microcontroller use...
annysky2012 stm32/stm8
Computer Simulation of High Frequency Electronic Circuits
I recently did two computer simulations of high-frequency electronic circuits... an AM receiver and an FM transmitter... They are very crude... I welcome your comments and suggestions......
open82977352 Talking
Gesture remote control
Gesture remote control Author: brother0952Project BackgroundToday's smart homes are developing very rapidly, and the ways to control home appliances are diverse, from the initial mechanical buttons, t...
brother0952 ST MEMS Sensor Creative Design Competition
How to properly place the inductor on the power supply PCB? You will understand it in seconds after reading this article!
[i=s]This post was last edited by ohahaha on 2019-6-3 11:25[/i] [font=微软雅黑][size=4] [/size][/font][align=center][b][font=微软雅黑][size=4]First, we ask the question: where should the coil be placed? [/siz...
ohahaha Energy Infrastructure?
When developing in MDK, how do I select the include parths in the Add TivaWare Hooks step? What is it used for?
When developing in MDK, how do I select the include parths in the Add TivaWare Hooks step? What is it used for?...
小海93 Microcontroller MCU
100-point entry-level interaction
I graduated with a bachelor's degree in computer science and now work in an electronics company, but not in design. I want to move into electronic design. Please give me a study plan. I don't know whe...
liu21b Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1939  920  1526  661  94  40  19  31  14  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号