EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-11203215AALF

Description
Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-11203215AALF Overview

Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle

51760-11203215AALF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
Board mount optionsHOLE .086-.098
body width0.47 inch
subject depth0.82 inch
body length8.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.135 inch
Termination typeSOLDER
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
Recommendations for making RF broadband amplifiers
[i=s] This post was last edited by paulhyde on 2014-9-15 03:18 [/i] First, when using transistors as amplifier circuits, the cutoff frequency is generally required to be more than 10 times the frequen...
longhaozheng Electronics Design Contest
How to configure the input and output of a GPIO in the TMS320C6000 series DSP?
1) Enable the general purpose input and output port peripheral (GPIO). // Enable the GPIO module (the corresponding peripheral module can also be enabled in BootLoader) PSCModuleControl(SOC_PSC_1_REGS...
Jacktang DSP and ARM Processors
Set 0xAA at SBUF, and return to switch(a), and cannot enter switch(a).
while(1) { if(RI) { RI = 0; a = SBUF; switch(a) { case 0xAA; .......... case 0xBB .......... } } } During simulation, I open the serial channel and set 0xAA at SBUF. When it reaches switch(a), it retu...
wy11104215 Embedded System
Working conditions and working characteristics of switching power supply
Working conditions of switching power supply:   1. Switch: Power electronic devices work in a switching state rather than a linear state   2. High frequency: Power electronic devices operate at high f...
唯小样 Power technology
[C5000 & C6000] dsp c5517 UART_TX_DMA sending problem?
dsp C5517: I receive serial data through UART receive interrupt, and I send data through UART_TX_DMA. There is no problem if I simply send data through UART_TX_DMA. If I send data through UART_TX_DMA,...
zhoujinming DSP and ARM Processors
DM9000AEP driver in uboot
After porting uboot1.1.6, everything is fine except the network function. But now ping is not working, and tftp cannot be used. The board has DM9000AEP chip. Netizens said that the uboot driver is not...
manman9258 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 306  1884  127  478  1665  7  38  3  10  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号