EEWORLDEEWORLDEEWORLD

Part Number

Search

54112-418541200LF

Description
Board Connector, 54 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size67KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54112-418541200LF Overview

Board Connector, 54 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54112-418541200LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
body width0.19 inch
subject depth0.472 inch
body length2.7 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number54112
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness79u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.095 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts54
PDM: Rev:G
STATUS:
Released
Printed: Feb 20, 2009
.
Debugging problem
I use MSP430F149 to debug the program. The single-step execution is correct during hardware simulation, but it is wrong when running at full speed. I don't know how to modify it. Please give me some a...
niuhaibing Microcontroller MCU
DIY Laser Engraving
Does anyone have the information and procedures for laser engraving? I am a student who has just started, so please help me....
1345 DIY/Open Source Hardware
Problems using save date
Has anyone used CCS to export programs? When using save date, there will be a requirement to set an address. What principle is used to design this address?...
安_然 Microcontroller MCU
About ADXL203 to measure tilt angle
When using ADXL203 to measure the tilt angle, the output should be 2.5V at 0° and 3.5V at 90°. The outputs I measured in the experiment were 2.5038V and 3.509V, which are basically correct. However, s...
lene ADI Reference Circuit
Use jlink to download the program to stm32, the jlink red light flashes, and finally the microcontroller cannot be recognized
When using jlink's sw mode to download the program, the debug window cannot recognize the MCU. jlink can be downloaded normally on other boards, so there is no problem with jlink, and there is no prob...
研究深 stm32/stm8
How can I create a WINCE emulator running on a PC with an ARMV4I CPU?
How can I use PB to create a WINCE simulator with ARMV4I CPU running on PC? Just explain the key steps. It seems that I cannot select two CPUs. If I select X86 and ARMV4I, there is no corresponding si...
bbs_cq Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 233  1090  997  2899  2698  5  22  21  59  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号