EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-114-55-1650R

Description
Board Connector, 110 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54122-114-55-1650R Overview

Board Connector, 110 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle

54122-114-55-1650R Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerAmphenol
Reach Compliance Codecompliant
body width0.19 inch
subject depth0.65 inch
body length5.5 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number54122
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts110
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
EPCS chip programming problem
I want to ask, after programming the EPCS chip through the CONFIG port, if I do not unplug the download line, the FPGA will not start up when I power it on again, nSTATUS will be pulled low, and CONF_...
eeleader-mcu FPGA/CPLD
Questions about multisim simulation
I was recently simulating a 555 oscillator. The square wave I output was input to a voltage follower and then connected to an integrator to get a triangle wave. The problem is as shown in the figure b...
音速兔 Analog electronics
Help, STM32F103 ADC problem
I use two ADCs for data acquisition. No matter in independent mode or synchronous mode, PA0 (channel 0) will have burr-like signals, and PA1 (channel 1) will have a level of about 1.7V (half of the 3....
laowen_110 stm32/stm8
TLC adopts AC voltage
I want to use TLC2543 to collect the instantaneous value of AC. The frequency of AC signal is only 50HZ. I wonder if the speed can be increased in time?...
晴歌 Analogue and Mixed Signal
Design of audio products based on DSP
With the acceleration of the digitalization process, digital signals will replace more analog signal environments. Since 2004, the application of DSP in consumer electronics will enter people's lives ...
fish001 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1720  2359  864  1265  843  35  48  18  26  17 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号