EEWORLDEEWORLDEEWORLD

Part Number

Search

380FS010NF08

Description
EMI/RFI Non-Environmental Backshell with Strain Relief
File Size75KB,2 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet View All

380FS010NF08 Overview

EMI/RFI Non-Environmental Backshell with Strain Relief

380-010
EMI/RFI Non-Environmental Backshell
with Strain Relief
Type D - Direct Coupling - Low Profile
38
A-B -C-D-E-F
G-H-J-K-L-S
* Conn. Desig. B See Note 5
CONNECTOR
DESIGNATORS
*
380 F S 010 M 16 05 F 6
Product Series
Connector
Designator
Angle and Profile
A = 90°
B = 45°
S = Straight
Basic Part No.
Length: S only
(1/2 inch increments:
e.g. 6 = 3 inches)
Strain Relief Style (F, G)
Cable Entry (Tables V, VI)
Shell Size (Table I)
Finish (Table II)
DIRECT COUPLING
TYPE D INDIVIDUAL
OR OVERALL SHIELD
TERMINATION
Length ± .060 (1.52)
Min. Order Length 2.0 Inch
(See Note 4)
A Thread
(Table I)
B
(Table I)
Length ± .060 (1.52)
Min. Order Length 1.5 Inch
(See Note 4)
STYLE 2
(STRAIGHT
See Note 1)
J
(Table III)
E
(Table IV)
J
(Table III)
G
(Table IV)
F (Table IV)
B
(Table I)
B
(Table I)
H
(Table IV)
STYLE F
Light Duty
(Table V)
.416 (10.5)
Max
Cable
Range
STYLE G
Light Duty
(Table VI)
.072 (1.8)
Max
K
Cable
Entry
L
© 2005 Glenair, Inc.
CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
E-Mail: sales@glenair.com
Series 38 - Page 58
Dear experts, why can't I view the peripherals connected to the FPGA side by address in DS-5? ?
[i=s]This post was last edited by yesea on 2017-3-24 11:55[/i] Dear experts, the development board I am using now is helio, which only runs a simple preloader, and even uboot does not run. Then I wrot...
yesea FPGA/CPLD
//---------How does TCPMP specify which frame to start playing and which frame to stop playing--------
How does TCPMP specify which frame to start playing and which frame to stop playing. In my project, the video file used is in AVI format. I plan to use TCPMP to accurately locate the start frame and e...
nuaajiang Embedded System
I made a USB to serial port using pl2303, but the computer can't detect it.
I made a USB to serial port with pl2303, but the computer can't detect it. Only when I connect the multimeter to pin 17 and ground, the computer can detect it. I have been looking for several days, pl...
phlelp Embedded System
Shunt Regulator for Faster Power Supply Startup
In certain applications, design requirements may require that the system's switch-mode power supply deliver output more quickly than a normal power supply. Figure 1 shows the bootstrap, or startup, ci...
zbz0529 Power technology
ARM9 2440 fails to read SHT11, all are 0XFF, what are the reasons?
ARM9 2440 failed to read SHT11, all 0XFF; after 2440 sent the command, no ACK signal was detected at the ninth clock. There should be no problem with the hardware, the same sensor runs normally on oth...
gw1300 ARM Technology
How to implement cc2530 ranging based on RSSI
How to measure the distance between two nodes (cc2530)? Currently I use afIncomingMSGPacket_t in the z-stack protocol stack to read the rssi value. Now I don't know what algorithm to use to calculate ...
HiAnt RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1330  193  2433  2389  1678  27  4  49  34  6 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号