EEWORLDEEWORLDEEWORLD

Part Number

Search

380LS002M20

Description
EMI/RFI Non-Environmental Backshell with Strain Relief
File Size92KB,2 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet View All

380LS002M20 Overview

EMI/RFI Non-Environmental Backshell with Strain Relief

380-002
EMI/RFI Non-Environmental Backshell
with Strain Relief
Type A - Direct Coupling - Low Profile
38
A-B -C-D-E-F
G-H-J-K-L-S
* Conn. Desig. B See Note 5
CONNECTOR
DESIGNATORS
*
380 F S 002 M 16 10 H 6
Product Series
Connector
Designator
Angle and Profile
A = 90°
B = 45°
S = Straight
Basic Part No.
Length: S only
(1/2 inch increments:
e.g. 6 = 3 inches)
Strain Relief Style
(H, A, M, D)
Cable Entry (Tables X, XI)
Shell Size (Table I)
Finish (Table II)
Length ± .060 (1.52)
Min. Order Length 2.5 Inch
(See Note 4)
DIRECT
COUPLING
TYPE A OVERALL
SHIELD TERMINATION
Length ± .060 (1.52)
Min. Order Length 3.0 Inch
(See Note 4)
A Thread
(Table I)
B
(Table I)
STYLE 2
(STRAIGHT
See Note 1)
J
(Table III)
E
(Table
IV)
F (Table IV)
J
(Table
III)
G
(Table
IV)
B
(Table I)
B
(Table I)
H (Table IV)
STYLE H
Heavy Duty
(Table X)
T
STYLE A
Medium Duty
(Table XI)
W
STYLE M
Medium Duty
(Table XI)
X
STYLE D
Medium Duty
(Table XI)
.135 (3.4)
Max
Cable
Range
V
Cable
Range
Y
Cable
Range
Y
Cable
Entry
Z
© 2005 Glenair, Inc.
CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
E-Mail: sales@glenair.com
Series 38 - Page 18
How to deal with impedance continuity of PCB traces?
[i=s]This post was last edited by qwqwqw2088 on 2020-12-16 07:46[/i]Everyone knows that impedance should be continuous. However, as Luo Yonghao said, "There are always times in life when you step on s...
qwqwqw2088 PCB Design
How to realize the fixed angle rotation of the smart car
Dear seniors, I am not clear about something, please give me some advice... How can I realize the intelligent car to rotate a fixed angle, such as turning left 90 degrees, etc. My car uses two reducti...
bank19841014 Embedded System
[Design Tips] How to configure UART and GPIO of SAM D and AVR
[size=4][b] Interface configuration is always a design step, but it is often cumbersome. [/b][/size] [size=4][b] Below Atmel engineers teach you the most commonly used GPIO and UART, and use the most ...
DreamerJane Microchip MCU
【Learning experience + MCU】TIVAC course is so good
The lecturer is Jin Yaer, who sounds like a foreigner. Today I watched the low power experiment 6. From preparation to success, including precautions, it is very detailed. I have to say it is a very g...
ddllxxrr Microcontroller MCU
[Question] Keywords: event object, DeviceIoControl
Can an application pass event objects to a driver via DeviceIoControl under WinCE?...
zdk Embedded System
What's that thing in the picture?
This is a switch circuit board. I want to know what the three black blocks on the top are. The black blocks (the one in the middle says hst-2027dr GROUP-TEK 0746 b)...
algor520 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2514  987  1341  1389  405  51  20  27  28  9 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号