Ordering number : ENA0683B
LE24C162M
Overview
CMOS IC
Two Wire Serial Interface EEPROM
(16k EEPROM)
The LE24C162M is a 2-wire serial interface EEPROM. It realizes high speed and a high level reliability by incorporating
SANYO’s high performance CMOS EEPROM technology. This device is compatible with I
2
C memory protocol,
therefore it is best suited for application that requires small-scale re-writable nonvolatile parameter memory.
Functions
•
Capacity: 16k bits (2k
×
8 bits)
•
Single supply voltage: 2.7V to 5.5V
•
Interface: Two wire serial interface (I
2
C Bus*)
•
Operating clock frequency: 400kHz
•
Low power consumption
: Standby: 2μA (max)
: Active (Read): 0.5mA (max)
•
Automatic page write mode: 16 Bytes
•
Read mode: Sequential read and random read
•
Erase/Write cycles: 10
6
cycles
•
Data Retention: 20 years
•
High reliability: Adopts SANYO’s proprietary symmetric memory array configuration (USP6947325)
Noise filters connected to SCL and SDA pins
Incorporates a feature to prohibit write operations under low voltage conditions.
* I
2
C Bus is a trademark of Philips Corporation.
* This product is licensed from Silicon Storage Technology, Inc. (USA), and manufactured and sold by
SANYO Semiconductor Co., Ltd.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer
'
s products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer
'
s products or
equipment.
91009 SY/70407 SY IM 20070412-S00011 No.0683-1/11
LE24C162M
Specifications
Absolute Maximum Ratings
Parameter
Supply voltage
DC input voltage
Over-shoot voltage
Storage temperature
Tstg
Below 20ns
Symbol
Conditions
Ratings
-0.5 to +6.5
-0.5 to +5.5
-1.0 to +6.5
-65 to +150
Unit
V
V
V
°C
Note: If an electrical stress exceeding the maximum rating is applied, the device may be damaged.
Operating Conditions
Parameter
Operating supply voltage
Operating temperature
Symbol
Conditions
Ratings
2.7 to 5.5
-40 to +85
Unit
V
°C
DC Electrical Characteristics
Parameter
Supply current at reading
Supply current at writing
Standby current
Input leakage current
Output leakage current (SDA)
Input low voltage
Input low voltage (CMOS)
Input high voltage
Input high voltage (CMOS)
Output low voltage
Symbol
ICC1
ICC2
ISB
ILI
ILO
VIL
VILC
VIH
VIHC
VOL
IOL=0.2mA
IOL=1.0mA
VDD*0.8
VDD-0.2
0.2
0.4
f=400kHz
f=400kHz, tWC=10ms
VIN=VDD or GND
VIN=GND to VDD
VOUT=GND to VDD
-2.0
-2.0
Conditions
min
VDD=2.7V to 5.5V
typ
max
0.5
3
2
+2.0
+2.0
VDD*0.2
0.2
mA
mA
μA
μA
μA
V
V
V
V
V
V
Unit
Capacitance/Ta=25°C,
f=1MHz
Parameter
In/Output pin capacitance
Input pin capacitance
Symbol
CI/O
CI
VI/O=0V (SDA)
VIN=0V (other than SDA)
Conditions
max
10
10
Unit
pF
pF
Note: This parameter is sampled and not 100% tested.
AC Electric Characteristics
Input pulse level
Input pulse rise / fall time
Output detection voltage
Output load
0.1×VDD to 0.9×VDD
20ns
0.5×VDD
50pF+Pull up resistor 3.0kΩ
VDD
R=3.0kΩ
SDA
C=50pF
Output Load Circuit
No.0683-3/11
LE24C162M
Pin Functions
SCL (serial clock input) pin
The SCL pin is a serial clock input pin that processes signals at the rising and falling edges of SCL clock signals.
This pin must be pulled up by a resistor to the VDD level and wired-ORed with an open drain (or open collector)
output device for use.
SDA (serial data input/output) pin
The SDA pin is used to transfer serial data to the input/output, and it consists of a signal input pin and n-channel
transistor open drain output pin.
Like the SCL pin, the SDA pin must be pulled up by a resistor to the VDD level and wired-ORed with an open drain
(or open collector) output device for use.
Functional Description
1 Start condition
When the SCL line is at the high level, the start condition is established by changing the SDA line from high to low.
The operation of the EEPROM as a slave starts in the start condition.
2 Stop condition
When the SCL line is at the high level, the stop condition is established by changing the SDA line from low to high.
When the device is set up for the read sequence, the read operation is suspended when the stop condition is received,
and the device is set to standby mode. When it is set up for the write sequence, the capture of the write data is ended
when the stop condition is received, and the EEPROM internal write operation is started.
tSU.STA
tHD.STA
tSU.STO
SCL
SDA
Start
condition
Stop
condition
3 Data transfer
Data is transferred by changing the SDA line while the SCL line is low. When the SDA line is changed while the SCL
line is high, the resulting condition will be recognized as the start or stop condition.
tSU.DAT
tHD.DAT
SCL
SDA
No.0683-5/11
Talking
京公网安备 11010802033920号
EEWORLD
