BD Voltage ................................................................30V
RT , V
C
Voltage ............................................................5V
RT Pin Current .........................................................1mA
SYNC Voltage ............................................................20V
FB Voltage ...................................................................5V
PG Voltage ................................................................30V
Operating Junction Temperature Range (Notes 4, 5)
LT3695E ............................................. –40°C to 125°C
LT3695I .............................................. –40°C to 125°C
LT3695H ............................................ –40°C to 150°C
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec) .................. 300°C
17
MSE PACKAGE
16-LEAD PLASTIC MSOP
θ
JA
= 40°C/W WITH EXPOSED PAD SOLDERED
θ
JA
= 110°C/W WITHOUT EXPOSED PAD SOLDERED
ORDER INFORMATION
LEAD FREE FINISH
LT3695EMSE#PBF
LT3695IMSE#PBF
LT3695HMSE#PBF
TAPE AND REEL
LT3695EMSE#TRPBF
LT3695IMSE#TRPBF
LT3695HMSE#TRPBF
PART MARKING*
3695
3695
3695
PACKAGE DESCRIPTION
16-Lead Plastic MSOP
16-Lead Plastic MSOP
16-Lead Plastic MSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
3695f
2
LT3695
ELECTRICAL CHARACTERISTICS
PARAMETER
Minimum Operating Voltage (Note 6)
V
IN
Overvoltage Lockout
Quiescent Current from V
IN
V
RUN/SS
= 0.2V
V
RUN/SS
= 10V, V
BD
= 3.3V, Not Switching
V
RUN/SS
= 10V, V
BD
= 0V, Not Switching
V
RUN/SS
= 0.2V
V
RUN/SS
= 10V, V
BD
= 3.3V, Not Switching
V
RUN/SS
= 10V, V
BD
= 0V, Not Switching
V
BD
= 3.3V
V
BD
< 3V
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
IN
= 10V, V
RUN/SS
= 10V, unless otherwise noted. (Note 4)
CONDITIONS
l
l
l
l
MIN
TYP
3.4
3.4
MAX
3.6
4.3
39.9
0.5
60
160
0.5
100
–5
3
808
815
–40
0.005
UNITS
V
V
V
μA
μA
μA
μA
μA
μA
V
mV
mV
nA
%/V
μS
V/V
μA
μA
A/V
36
38
0.01
35
90
Quiescent Current from BD Pin
l
35
0.01
55
0
2.8
800
800
–5
0.001
430
1300
50
50
1.25
Minimum BD Pin Voltage
Feedback Voltage
FB Pin Bias Current
Reference Voltage Line Regulation
Error Amp g
m
Error Amp Voltage Gain
V
C
Source Current
V
C
Sink Current
V
C
Pin to Switch Current Gain
V
C
Switching Threshold
V
C
Clamp Voltage
Switching Frequency
R
RT
= 8.06k
R
RT
= 29.4k
R
RT
= 158k
E- and I-Grades
H-Grade
SYNC = 0V
SYNC = 3.3V or Clocked
I
SW
= 1A
1.25
V
SW
= 0V, V
IN
= 36V
l
l
l
792
785
FB Pin Voltage = 800mV
3.6V < V
IN
< 36V
I
VC
= ±1.5μA
l
0.4
1.98
0.9
225
0.6
2
2.2
1.0
250
130
130
0.8
2.42
1.1
275
210
250
2
1.66
1.95
1
V
V
MHz
MHz
kHz
ns
ns
A
A
mV
A
μA
Minimum Switch Off-Time
Switch Current Limit (Note 7)
Switch V
CESAT
DA Pin Current to Stop OSC
Switch Leakage Current
1.45
1.18
1.7
1.4
350
1.6
0.01
3695f
3
LT3695
ELECTRICAL CHARACTERISTICS
PARAMETER
Boost Schottky Diode Voltage Drop
Boost Schottky Diode Reverse Leakage
Minimum Boost Voltage (Note 8)
BOOST Pin Current
RUN/SS Pin Current
RUN/SS Input Voltage High
RUN/SS Input Voltage Low
PG Leakage Current
PG Sink Current
PG Threshold as % of V
FB
PG Threshold Hysteresis
SYNC Threshold Voltage
SYNC Input Frequency
Note 1:
Stresses beyond those listed under absolute maximum ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect the device
reliability and lifetime.
Note 2:
Positive currents flow into pins, negative currents flow out of pins.
Minimum and maximum values refer to absolute values.
Note 3:
Absolute maximum voltage at V
IN
and RUN/SS pins is 60V for
nonrepetitive 1 second transients, and 36V for continuous operation.
Note 4:
The LT3695E is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LT3695I is guaranteed over the full –40°C to 125°C operating junction
temperature range. The LT3695H is guaranteed over the full –40°C to
150°C operating junction temperature range.
V
PG
= 5V
V
PG
= 0.4V
Measured at FB Pin (Pin Voltage Rising)
Measured at FB Pin
300
0.3
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
IN
= 10V, V
RUN/SS
= 10V, unless otherwise noted. (Note 4)
CONDITIONS
I
BSD
= 50mA
V
SW
= 10V, V
BD
= 0V
l
MIN
TYP
720
0.1
1.7
10.5
4.5
12
MAX
900
1
2.3
17.5
7.5
20
0.2
UNITS
mV
μA
V
mA
μA
μA
V
V
μA
μA
%
mV
mV
MHz
I
SW
= 0.5A
V
RUN/SS
= 2.5V
V
RUN/SS
= 10V
l
2.5
0.1
100
88
1000
90
12
550
800
2.2
92
1
Note 5:
This IC includes overtemperature protection that is intended to
protect the devices during momentary overload conditions. Junction
temperature will exceed the maximum operating junction temperature
when overtemperature protection is active. Continuous operation above
the specified maximum operating junction temperature may impair device
reliability.
Note 6:
This is the voltage necessary to keep the internal bias circuitry in
regulation.
Note 7:
Current limit guaranteed by design and/or correlation to static test.
Slope compensation reduces current limit at higher duty cycles.
Note 8:
This is the minimum voltage across the boost capacitor needed to
In the interrupt handling mechanism of the STM32 microcontroller, are the functions of the interrupt flag bit and the interrupt pending flag bit repeated?...
When there are multiple SPI slaves, if the chip select signal is set to enable more than two slaves at the same time, what should I do if the two slaves send data to the master at the same time? SPI a...
First of all, I am very happy to get the GD32E503V development board review. Since I started to use GD's MCU last year, I think this domestic MCU is simply amazing! Not only is it better than STM32 in...
As the title says, if you want to install a new input method by writing to the registry, what should you do? ? Taking the full-pinyin input method as an example, in addition to writing the two files w...
International Solar Photovoltaic Network News: Chinese inverter company Sungrow announced that it will build a 3GW photovoltaic inverter manufacturing plant in Bangalore, the capital of Karnataka, ...[Details]
Recently, the U.S. Department of Commerce announced that it would prohibit companies in the country from selling any electronic technology or communication components to ZTE, a Chinese communicatio...[Details]
In the past few days, the Chinese display panel giant
BOE
has been flooded with articles supported by Liu Shuwei. Let's follow the embedded editor to learn about the relevant content.
...[Details]
1. Test conditions Hardware: STM32L432KC Main frequency: 80MHz Compiler: IAR 8.20.1 Compiler options: High Speed no size constraints CRC generator polynomial: 0x782f 2. Test Method The softwar...[Details]
Unique device identifiers are suitable for: ● Used as a serial number (e.g. USB string serial number or other terminal applications) ● Use the unique ID as a security key when used in conjunction wit...[Details]
The update interrupt initialization configuration of the stm32 advanced timer TIM1 is not much different from that of the ordinary timer. What needs to be paid attention to is the configuration of TI...[Details]
After searching a lot of information, I finally understood the time base timer. I did not use any library functions but operated the registers directly. The following introduces the systick in STM32...[Details]
All relevant units:
In accordance with the relevant requirements of the provincial and municipal electric vehicle charging infrastructure construction work, in order to further standardize the...[Details]
The goal of this article is to build a TCP client based on the previous project that can ping the PC, and can actively send data to the PC, and can also send and receive data with the PC, and display...[Details]
1. Basic Concepts of LCD/LCM The structure of Liquid Crystal Display (LCD) is to place liquid crystals between two parallel pieces of glass. There are many vertical and horizontal fine wires between...[Details]
At present, in the world,
the construction of
smart cities
is in the process of gradually landing from concept, and technology giants and investment giants are important participants in this...[Details]
The application of millimeter wave technology in mobile communications also involves a series of technical problems, including the large propagation loss of millimeter waves and the susceptibility ...[Details]
In the project, CPLD is needed to complete part of the algorithm design. The parameters are given by AVR, so the communication between AVR and CPLD needs to be completed. Therefore, a test program is...[Details]
The article is written for LPC2148, but it is also applicable to Samsung's 44B0 chip. You only need to select S3C44B0 as the corresponding CPU when selecting it. JLINK debugging experience un...[Details]
I used the bit definition in my 51 program: bit flag. After defining it this way, I ran the program and downloaded it to the circuit board. I found that the flag was not the value I set, which led to...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
