The ASM3P2870A uses the most efficient and optimized
modulation profile approved by the FCC and is
implemented by using a proprietary all digital method.
The ASM3P2870A modulates the output of a single PLL
in order to “spread” the bandwidth of a synthesized clock,
and more importantly, decreases the peak amplitudes of
its harmonics. This results in significantly lower system
EMI compared to the typical narrow band signal produced
by oscillators and most frequency generators. Lowering
EMI by increasing a signal’s bandwidth is called ‘spread
spectrum clock generation’.
Applications
The ASM3P2870A is targeted towards all portable
devices with very low power requirements like MP3
players and digital still cameras.
Product Description
The ASM3P2870A is a versatile spread spectrum
frequency modulator designed specifically for a wide
range of clock frequencies. The ASM3P2870A reduces
electromagnetic interference (EMI) at the clock source,
allowing system wide reduction of EMI of
all clock
dependent signals. The ASM3P2870A allows significant
system cost savings by reducing the number of circuit
board layers ferrite beads, shielding that are traditionally
required to pass EMI regulations.
Key Specifications
Description
Supply voltages
Cycle-to-Cycle Jitter
Output Duty Cycle
Modulation Rate Equation
Frequency Deviation
Specification
V
DD
= 3.3V / 2.5V
200pS (Max)
45/55%
F
IN
/640
±0.75% ( Typ ) @ 22MHz
Block Diagram
V
DD
XIN
Crystal
Oscillator
Frequency
Divider
Feedback
Divider
REFOUT
Modulation
PLL
XOUT
Phase
Detector
Loop
Filter
VCO
Output
Divider
ModOUT
V
SS
Alliance Semiconductor
2575 Augustine Drive
•
Santa Clara, CA
•
Tel: 408.855.4900
•
Fax: 408.855.4999
•
www.alsc.com
Notice: The information in this document is subject to change without notice.
September 2005
rev 1.5
Pin Configuration (6-pin TSOT- 23 Package)
ASM3P2870A
REFOUT
1
XOUT
2
6
V
SS
ModOUT
V
DD
ASM3P2870A
5
4
XIN / CLKIN
3
Pin Description
Pin#
1
2
3
4
5
6
Pin Name
REFOUT
XOUT
XIN / CLKIN
V
DD
ModOUT
V
SS
Type
O
O
I
P
O
P
Description
Buffered output of the input frequency
Crystal connection. If using an external reference, this pin must be left unconnected.
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
Power supply for the entire chip.
Spread spectrum clock output.
Ground connection.
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
2 of 12
September 2005
rev 1.5
Pin Configuration (8-pin SOIC and TSSOP Packages)
ASM3P2870A
XIN / CLKIN
XOUT
REFOUT
NC
1
2
3
4
8
7
6
5
V
DD
NC
ModOUT
V
SS
ASM3P2870A
Pin Description
Pin#
1
2
3
4
5
6
7
8
Pin Name
XIN/CLKIN
XOUT
REFOUT
NC
V
SS
ModOUT
NC
V
DD
Type
I
O
O
-
P
O
-
P
Description
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
Crystal connection. If using an external reference, this pin must be left unconnected.
Buffered output of the input frequency
No connect.
Ground connection.
Spread spectrum clock output.
No connect.
Power supply for the entire chip.
Modulation Profile
Specifications
Description
Frequency Range
For 2.5V Supply
For 3.3V Supply
Specification
13MHz < CLKIN < 30MHz
F
IN
/640
+0.75%(Typ) @22MHz
Modulation Equation
Frequency Deviation
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
3 of 12
September 2005
rev 1.5
Absolute Maximum Ratings
Symbol
V
DD
, V
IN
T
STG
T
A
T
s
T
J
T
DV
Storage temperature
Operating temperature
Max. Soldering Temperature (10 sec)
Junction Temperature
Static Discharge Voltage
(As per JEDEC STD22- A114-B)
ASM3P2870A
Parameter
Rating
-0.5 to +7.0
-65 to +125
0 to 70
260
150
2
Unit
V
°C
°C
°C
°C
KV
Voltage on any pin with respect to Ground
Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect
device reliability.
DC Electrical Characteristics for 2.5V Supply
(Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated)
Symbol
V
IL
V
IH
I
IL
I
IH
I
XOL
I
XOH
V
OL
V
OH
I
DD
I
CC
V
DD
t
ON
Z
OUT
Input low voltage
Input high voltage
Input low current
Input high current
Parameter
Min
V
SS
- 0.3
2.0
-
-
-
-
-
1.8
-
-
2.375
-
-
Typ
-
-
-
-
3
3
-
-
1.0
3.0
2.5
-
50
Max
0.8
V
DD
+ 0.3
-35
35
-
-
0.6
-
-
-
2.625
5
-
Unit
V
V
µA
µA
mA
mA
V
V
mA
mA
V
mS
Ω
XOUT output low current (@0.5V, V
DD
=2.5V)
XOUT output high current (@1.8V, V
DD
=2.5V)
Output low voltage (V
DD
= 2.5 V, I
OL
= 8mA)
Output high voltage (V
DD
= 2.5 V, I
OH
= 8mA)
Static supply current*
Dynamic supply current (2.5V, 22MHz and no load)
Operating Voltage
Power-up time (first locked cycle after power-up)
Output impedance
* XIN /CLKIN pin is pulled low
AC Electrical Characteristics for 2.5V Supply
Symbol
CLKIN
ModOUT
f
d
t
LH
*
t
HL
*
t
JC
t
D
Input frequency
Output frequency
Frequency Deviation
Input Frequency = 13MHz
Input Frequency = 30MHz
Parameter
Min
13
13
-
-
0.7
0.4
-
45
Typ
-
-
± 1.20
± 0.5
1.4
0.8
-
50
Max
30
30
-
-
1.6
1.0
200
55
Unit
MHz
MHz
%
nS
nS
pS
%
Output rise time (measured from 0.7V to 1.7V)
Output fall time (measured from 1.7V to 0.7V)
Jitter (cycle to cycle)
Output duty cycle
* t
LH
and t
HL
are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
4 of 12
September 2005
rev 1.5
DC Electrical Characteristics for 3.3V Supply
(Test condition: All parameters are measured at room temperature (+ 25°C) unless otherwise stated)
ASM3P2870A
Symbol
V
IL
V
IH
I
IL
I
IH
I
XOL
I
XOH
V
OL
V
OH
I
DD
I
CC
V
DD
t
ON
Z
OUT
Input low voltage
Input high voltage
Input low current
Input high current
Parameter
Min
V
SS
- 0.3
2.0
-
-
-
-
-
2.5
-
-
2.7
-
-
Typ
-
-
-
-
3
3
-
-
1.2
4.0
3.3
-
45
Max
0.8
V
DD
+ 0.3
-35
35
-
-
0.4
-
-
-
3.6
5
-
Unit
V
V
µA
µA
mA
mA
V
V
mA
mA
V
mS
Ω
XOUT output low current (@0.4V, V
DD
=3.3V)
XOUT output high current (@2.5V, V
DD
=3.3V)
Output low voltage (V
DD
= 3.3 V, I
OL
= 8mA)
Output high voltage (V
DD
= 3.3 V, I
OH
= 8mA)
Static supply current*
Dynamic supply current (3.3V, 22MHz and no load)
Operating Voltage
Power-up time (first locked cycle after power-up)**
Output impedance
* XIN /CLKIN pin is pulled low.
AC Electrical Characteristics for 3.3V Supply
Symbol
CLKIN
ModOUT
f
d
t
LH
*
t
HL
*
t
JC
t
D
Input frequency
Output frequency
Frequency Deviation
Input Frequency = 13MHz
Input Frequency = 30MHz
Parameter
Min
13
13
-
-
0.4
0.3
-
45
Typ
-
-
±1.20
± 0.5
1.2
0.8
-
50
Max
30
30
-
-
1.5
1.1
200
55
Unit
MHz
MHz
%
nS
nS
pS
%
Output rise time (measured from 0.8 to 2.0V)
Output fall time (measured at 2.0V to 0.8V)
Jitter (cycle to cycle)
Output duty cycle
*t
LH
and t
HL
are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
I'm a newbie, I recently found a job in Suzhou, working in radio frequency. I want to find some information and posts about wifi in the forum, but I found that there are not many. I just suggest:congr...
[size=3][font=宋体]Market Overview[/font][/size] [color=black][font=宋体]The domestic[/font][/color][color=black][font=Times New Roman]DVR[/font][/color][color=black][font=宋体]industry has experienced deve...
The program compiled successfully with evc is downloaded to the system through USB and can be run. Now I want to put it on a USB disk and run it under wince. How can I do it? Please give me some advic...
[i=s] This post was last edited by paulhyde on 2014-9-15 09:45 [/i] The basic requirements for designing a digital voltage source with a certain output voltage range and function are (1) Output voltag...
Typically, the implementation of a video processing system needs to support a variety of video and audio standards and is responsible for converting signals from one standard to another. Multimedia ap...
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
