FHR 2/4 8065 80110 80216 80320 80370
Powertron
•
•
•
•
•
•
Resistances from 0.001Ohm to 500Ohms
Power Rating to 2500Watt
Resistance Tolerances to ±0.1%
TCR to ±15ppm/K
Load Stability to 0.1%
Very Low Inductance (<50nH)
SPECIFICATIONS
Type
Resistance Range
Power rating
free air 25°C
with heatsink
Thermal Resistance Rthj-c
Tolerances (4 terminal version)
from 0.001 Ohms
from 0.01 Ohms
from 0.02 Ohms
Tolerances (2 terminal version)
Stability
Temperature Coefficient (4 terminal version)
8065
0.001 to 400Ohms
24 W
350 W
0.16 K/W
80110
32 W
600 W
0.09 K/W
80216
60 W
1200 W
0.04 K/W
80320
80 W
2000 W
0.026 K/W
80370
90 W
2500 W
0.022 K/W
0.001 to 500Ohms
0.5% / 1% / 2% / 5%
0.25% / 0.5% / 1% / 2% / 5%
0.1% / 0.25% / 0.5% / 1% / 2% / 5%
0.5% / 1% / 2% / 5%
0.1% / 0.2% / 0.5%
(depends on stress)
±15ppm/K (20 to 60°C)
from R ≤ 0.02 Ohms ±20ppm/K (20 to 60°C)
from R ≤ 0.01 Ohms ±30ppm/K (20 to 60°C)
±15ppm/K (20 to 60°C)
±50ppm/K (-40 to 130°C)
R ≤ 0.2 Ohms TCR see table A next page
60 A
upon request special cable up to 250 A
< 50 nH
500 pF
850 pF
1.7 nF
< 0.1µV/K
-40 to 130°C
CuNiMn-Foil
anodized aluminium
anodized aluminium
Cu-Cable / 4mm² / 500mm lenght
(other upon request / AWG possible)
2 or 4
2.5 nF
2.9 nF
1.5 kVDV (higher upon request)
Temperature Coefficient (2 terminal version)
Max. Current
Inductivity
Capacity against housing
Insulation Strenght
Thermal EMF
Operating Temperature Range
Resistor Material
Substrate
Housing
Connector Material
Terminals
Ordering Information
Part Number - Resistance - Contact - Tolerance
FHR 4-80216 1.0 Ohms D 1%
Document Number: 64202
Revision: 20-09-10
For technical questions, contact:
powertron@vishaypg.com
www.powertron.de
1
FHR 2/4 8065 80110 80216 80320 80370
Powertron
SPECIFICATIONS
(continued)
Temperature Coefficient
4000
250
table A
2000
DR/R
(ppm)
+15ppm/K
200
0
TCR-Shift (ppm/K)
150
-2000
-15ppm/K
100
-4000
Limit 2 (3s)
-6000
Nominal
DR/R
Limit 1 (3s)
50
0
10
20
50
2
5
100
200
-8000
-40
-20
0
20
40
60
Temperature (°C)
80
100
120
140
Resistance Value (mOhm)
Derating
120
Power ( % from
nominal power)
Power Rating Notes -
100
80
60
40
20
0
25
0.5%
0.2%
0.1%
The FHR Series Resistors must be attached to a suitable heat-
sink. The maximum internal resistor temperature is 130°C.
To specify an appropriate heatsink use the following formula :
R
qH
= T
MAX
- ( P x R
qR
) - T
A
P
Where:
50
75
85
100
115
130
Temperature of the backplate (°C)
Dimensions
R
qH
= Thermal Resistance of Heatsink ( K/W )
R
qR
= Thermal Resistance of Resistor ( K/W )
T
MAX
= Maximum Temperature of Resistor
T
A
= Ambient Temperature of Heatsink ( °C )
P = Power Through Resistor ( W )
Dimension
B
C
D
E
F
G
mm
80.00
60.00
Ø4.75
15.00
67.00
2.00
tol.
(±mm)
0.3
0.3
0.2
0.2
0.3
0.1
inches
3.15
2.36
Ø0.19
0.59
2.64
0.08
tol.
(±inches)
0.012
0.012
0.008
0.008
0.012
0.004
Dimension
A
L1
L2
L3
L4
8065
mm
65.00
6.00
59.00
80110
mm
110.00
6.00
104.00
80216
mm
216.00
6.00
108.00
210.00
80320
mm
320.00
6.00
108.50
211.50
314.00
80370
mm
370.00
6.00
125.50
244.50
364.00
tol.
(±mm)
0.3
0.3
0.3
0.3
0.3
8065
inches
2.56
0.24
2.32
80110
inches
4.33
0.24
4.09
80216
inches
8.50
0.24
4.25
8.27
80320
inches
12.60
0.24
4.27
8.33
12.36
80370
inches
14.57
0.24
4.94
9.63
14.33
tol.
(±inches)
0.012
0.012
0.012
0.012
0.012
www.powertron.de
2
For technical questions, contact:
powertron@vishaypg.com
Document Number: 64202
Revision: 20-09-10
FHR 2/4 8065 80110 80216 80320 80370
Powertron
SPECIFICATIONS
(continued)
Stability against Impulses
Reference values without heatsink
Resistance value R001 to R002
100000
80370
80320
80216
80110
8065
Impuls Energy (J)
10000
1000
100
01
02
05
00
00
00
0,
0,
0,
0,
0,
0,
Impulse Time (s)
Resistance value R002 to R005
100000
80370
80320
80216
80110
8065
Impuls Energy
10000
1000
100
0,
01
0,
02
0,
05
0,
1
0,
2
0,
5
10
20
50
1
2
5
1
2
5
00
00
0,
0,
0,
00
Impulse Time (s)
Resistance value R005 to R01
100000
80370
80320
80216
80110
8065
Impulse Energy (J)
10000
1000
100
01
02
05
1
2
5
10
20
50
1
2
5
1
2
5
00
00
00
0,
0,
0,
0,
0,
0,
Impulse Time (s)
Document Number: 64202
Revision: 20-09-10
For technical questions, contact:
powertron@vishaypg.com
www.powertron.de
3
10
0,
0,
0,
0
10
0
10
0
1
2
5
10
20
0,
0,
0,
50
1
2
5
1
2
5
FHR 2/4 8065 80110 80216 80320 80370
Powertron
SPECIFICATIONS
(continued)
Stability against Impulses
Reference values without heatsink
Resistance value R01 to R1
100000
80370
80320
80216
80110
8065
Impulse Energy (J)
10000
1000
100
01
02
05
1
2
5
10
20
00
1
00
2
00
5
50
1
2
5
0,
0,
0,
0,
0,
0,
Impulse Time (s)
Resistance value R1 to 1R
100000
10000
1000
100
10
80370
80320
80216
80110
8065
Impulse Energy (J)
1
2
5
0,
0
0,
0
0,
00
0,
00
0,
00
0,
0
Im pulse Tim e (s)
Resistance value 1R to 10R
100000
80370
80320
80216
80110
8065
Impulse Energy (J)
10000
1000
100
10
01
02
05
1
2
5
10
20
50
1
2
5
1
2
5
00
00
00
0,
0,
0,
0,
0,
0,
Impulse Time (s)
www.powertron.de
4
For technical questions, contact:
powertron@vishaypg.com
Document Number: 64202
Revision: 20-09-10
10
0,
0,
0,
0
10
0
0,
1
0,
2
0,
5
10
20
50
1
2
5
1
2
5
10
0,
0,
0,
0
FHR 2/4 8065 80110 80216 80320 80370
Powertron
SPECIFICATIONS
(continued)
Stability against Impulses
Reference values without heatsink
Resistance value 10R to 100R
100000
80370
80320
80216
80110
8065
Impulse Energy (J)
10000
1000
100
10
01
02
05
00
00
00
0,
0,
0,
0,
0,
0,
Impulse Time (s)
Resistance value 100R to 500R
100000
80370
80320
80216
80110
8065
Impulse Energy (J)
10000
1000
100
10
0,
01
0,
02
0,
05
0,
00
0,
00
0,
00
Impulse Time (s)
Lead Variations
Standard:
optional:
Lead D
Lead H1
Lead H2
Lead H3
Lead H4
Lead H5
Lead H6
from to 60 A
from to 70 A
from to 85 A
from to 100 A
from to 120 A
from to 150 A
from to 250 A
isolated round cable (Cu / tinned)
isolated Cu - flat cable
isolated Cu - flat cable
isolated Cu - flat cable
isolated Cu - flat cable
isolated Cu - flat cable
isolated Cu - flat cable
Document Number: 64202
Revision: 20-09-10
For technical questions, contact:
powertron@vishaypg.com
www.powertron.de
5
10
0
1
2
5
10
20
0,
0,
0,
50
1
2
5
1
2
5
10
0
0,
1
0,
2
0,
5
10
20
50
1
2
5
1
2
5
Integrated technical exchanges
京公网安备 11010802033920号
EEWORLD
