EEWORLDEEWORLDEEWORLD

Part Number

Search

M55342M10B3B48RT5

Description
RESISTOR, THIN FILM, 0.5 W, 0.1 %, 300 ppm, 3480 ohm, SURFACE MOUNT, 1010, CHIP
CategoryPassive components    The resistor   
File Size111KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

M55342M10B3B48RT5 Overview

RESISTOR, THIN FILM, 0.5 W, 0.1 %, 300 ppm, 3480 ohm, SURFACE MOUNT, 1010, CHIP

M55342M10B3B48RT5 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerVishay
package instructionSMT, 1010
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresNON-INDUCTIIVE, LASER TRIMMABLE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length2.667 mm
Package formSMT
Package width2.54 mm
method of packingTR
Rated power dissipation(P)0.5 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance3480 Ω
Resistor typeFIXED RESISTOR
size code1010
surface mountYES
technologyTHIN FILM
Temperature Coefficient300 ppm/°C
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage75 V
E/H (Military M/D55342)
Vishay Thin Film
QPL MIL-PRF-55342 Qualified Thin Film Resistor Chips
FEATURES
Established reliability, “R” failure rate level (100 ppm), C = 2
High purity alumina substrate 99.6 % purity
Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+ 150 °C operating conditions
Very low noise and voltage coefficient
(< - 25 dB, 0.5 ppm/V)
Non-inductive
Laser-trimmed tolerances ± 0.1 %
Wraparound resistance less than 0.010
Ω
typical
In-lot tracking less than 5 ppm/°C
Complete MIL-testing available in-house
Antistatic waffle pack or tape and reel packaging available
Military/aerospace/QPL
SURFACE MOUNT
CHIPS
Actual Size
M55342/02
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing. Wafer is sawed producing exact dimensions and
clean, straight edges.
Note
Specification changed
MIL-PRF-55342
by
DSCC
from
MIL-R-55342
to
CONSTRUCTION
TYPICAL PERFORMANCE
ABS
Passivation
Resistor film
Solder
coating
Nickel barrier
High ourity
alumina substrate
Adhesion layer
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
Test
Material
Absolute TCR
Absolute Tolerance
Stability:
ΔR
Absolute
Voltage Coefficient
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability
SPECIFICATIONS
Passivated nichrome
± 25 ppm/°C to ± 300 ppm/°C TCR
± 0.1 %
± 0.1 %
± 0.5 ppm/V
- 55 °C to + 125 °C
- 55 °C to + 150 °C
- 25 dB
100 ppm
1 year at + 25 °C
- 55 °C to + 125 °C
+ 25 °C
2000 h at + 70 °C
CONDITIONS
www.vishay.com
50
For technical questions, contact:
thin-film@vishay.com
Document Number: 60018
Revision: 16-Sep-09
Failure characteristics of electronic components
Although there are a large number of electronic components inside electrical equipment, their failures follow certain patterns....
fighting PCB Design
PSpice Classic Chinese Tutorial
The general PSpice classic Chinese tutorial is a good material for beginners. However, the examples given are relatively simple, so I will just give you some ideas....
linda_xia Microchip MCU
【Ask TI】LM3S Series LMLINK
According to the configuration on the ZLG website, LMLINK uses IAR When I switched to keil, I couldn't use LMlink Is the LMlink light flashing different from the IAR driver?...
常见泽1 Microcontroller MCU
Is the port in high impedance state after STM32 reset?
I used STM32F103C6T6, and added a buffer chip 74LV07 through a port to drive the optocoupler at a low level. I found that sometimes the load of the optocoupler was turned on during the power-on proces...
zhangjmxx stm32/stm8
In an AC circuit, what is the phase relationship between the voltage across R and the current flowing through the inductor?
I would like to ask a question here. In an AC circuit, what is the phase relationship between the voltage across R and the current flowing through the inductor? eeworldpostqq...
蓝猫淘气 Analog electronics
I made a 2812 board myself, and the reset pin generates a periodic low level?
I made a 2812 board by myself. The 3.3v and 1.8v power supplies are very stable. I use power-on reset instead of the reset signal of TPS767D318. I use key reset. After power-on, the reset pin always g...
a2479104 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2165  51  2470  293  2374  44  2  50  6  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号