The power good (PG) pin is used in many of TI's TPS62x family of step-down converters to indicate whether the output voltage is still being supplied during normal operation of the device. The PG pin i...
[color=rgb(0, 0, 0)][font=微软雅黑][align=left][font=宋体]In order to provide friends in the industry with a more comprehensive comparison of Chinese and English professional terms for [/font]LED[font=宋体]en...
Program to read and write 24c512 with msp430 /************************************************************ *File name: msp430f169i2c.c *Overall description: MSP430F169 microcontroller hardware IIC sof...
[size=4] Aiming at the problems of dynamics and stability in the synchronous control of multiple units of printing and dyeing equipment, a design scheme of embedded synchronous controller based on DSP...
Refer to the test introduction of the two-terminal resistor network. The maximum protection current of the 2400 protection buffer is 50mA . To calculate the current source setting for the 8 -pin R1/R2...
For 80,000
ZTE
(000063.SZ) employees and more Chinese ICT (information and communication technology) industry practitioners, the news from across the ocean on the evening of April 16 kept t...[Details]
"Originally, there are many people who can design very good
chips
, but the market does not give domestic
chips
the opportunity to iterate, and domestic companies cannot give engine...[Details]
1. Principle 1. Infrared emission protocol There are many infrared communication protocols. This experiment uses the NEC protocol. This protocol uses PWM modulation and uses pulse width to represen...[Details]
In the actual project development process, we often need to get the running time of a section of code. The usual method is to use an oscilloscope to measure it. This blog post will use SysTick to acc...[Details]
Today, under the guidance of a low-level expert, I learned how to configure the PWM module! Woof! First open the file configured last time, as follows: Then, we need to use TIM1 to set PWM: Then,...[Details]
Regarding the PHY construction of LWIP, the PHY chip used is LAN8720A, RMII mode. Regarding the hardware connection part, the Atomic board F407 is used, and the hardware connection is as follows: ...[Details]
I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]
Timing and protocol are two key points in digital system debugging, and they are also where logic analyzers can play their most valuable role. How can we use a logic analyzer to quickly complete wiri...[Details]
Superconductors have physical properties such as zero resistance effect, Meissner effect and Josephson effect, which make them have broad application prospects and unparalleled advantages in many b...[Details]
The adoption rate of serverless
cloud
computing
is gradually increasing, but it has not yet reached people's expectations. Various surveys show that serverless
is
still
an eme...[Details]
As cryptocurrency continues to gain popularity, a technology hidden behind it has attracted more attention from the world, that is the now hotly debated
blockchain
. Let's follow the embedd...[Details]
Mobile communication resale business means that enterprises can contract part of the communication network usage rights from basic telecommunications operators, repackage them into their own brands...[Details]
OSC_IN and OSC_OUT are external crystal pins by default. If you do not use an external crystal oscillator on the STM32, how to connect OSC_IN and OSC_OUT If you use the internal RC oscillator instead...[Details]
/* Unfortunately, it cannot generate a standard 38kHz frequency square wave, there is a little error*/ #include reg51.h #define uchar unsigned char #define uint unsigned int sbit Waveout=P1^0; //P...[Details]
As shown in the figure, the circuit is required to count and display the number of times the button is pressed. When the button is pressed once, the count value increases by 1 (it is required to accu...[Details]