EEWORLDEEWORLDEEWORLD

Part Number

Search

LC160M1000BPF43035

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum, 160V, 20% +Tol, 20% -Tol, 1000uF
CategoryPassive components    capacitor   
File Size197KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

LC160M1000BPF43035 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum, 160V, 20% +Tol, 20% -Tol, 1000uF

LC160M1000BPF43035 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompli
ECCN codeEAR99
capacitance1000 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter30 mm
dielectric materialsALUMINUM
length35 mm
Manufacturer's serial numberLC
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-25 °C
Package formSnap-i
method of packingBulk
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)160 V
ripple current2150 mA
seriesLC
Terminal pitch10 mm
YAGEO CORPORATION
ELECTROLYTIC CAPACITORS
LC
[ High Temperature and Long Life ]
105°C 5000 Hours, Wide Temperature Range and Long Life
Large Can Aluminum
Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -25 ~ +105°C
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
160 ~ 450VDC
270 ~ 2200μF
±20% at 120Hz, 20°C
Leakage Current (Max.) (20°C) : I = 0.02CV or 3μA whichever is greater.
(After Rated Voltage Applied for 5 Minutes)
Dissipation Factor (Max. tanδ) Rated Voltage (V)
(20°C, 120Hz)
Endurance
D.F (%)
160~400
15
450
25
Longer life than HW, Snap-in termainal, High ripple current.
Applications: Smoothing circuit, TV/Monitor, Adapter, SMPS
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
COEFFICIENT
FREQUENCY (Hz)
COEFFICIENT
50
IK
60
2.4K
120
1.00
5K
1.36
400
1.14
10K
1.40
0.80 0.85
1.23 1.30
DESCRIPTION
After the rated voltage has been applied at 105°C for 5000 hours, the
capacitors shall meet the following requirements.
(a) Capacitance Change : Within ±20% of Initial Value
(b) Dissipation Factor: Not Exceeding 200% of the Specified Value
(c) Leakage Current: Not Exceeding the Specified Value
Shelf Life
After having been placed at 105°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
DIAGRAM OF DIMENSIONS
Location of P.C.B. Holes
Vinyl Sleeve
Unit: mm
10
±
0.5
Negative
0.9
±
0.1
10
±
0.5
2mm x 2
Botton Plate
3.0
0.8+0.2/-0.1
5.8
±
1.0
Safety Device
L+2 Max.
5.8
±
1
D
±
1
1.5+0.2/-0.1
Free evaluation - Topmicro intelligent display module (2) displays a picture
[i=s]This post was last edited by wenyangzeng on 2021-11-1 14:40[/i]Free evaluation - Topmicro intelligent display module (2) displays a pictureAccording to the HMT070ETD-1D manual, the display resolu...
wenyangzeng Test/Measurement
[Help] Cadence creates a new component
It's so painful, even more painful than writing a program. How do I create a new component? I know its PCB package, but I can't find the schematic diagram, so I have to draw the schematic diagram myse...
ywlzh PCB Design
OPA551 is powered by a single 24V power supply and will get hot even without a load.
Connect as shown in the figure below, and connect as a voltage follower. When OPA551 is powered by 24V, it becomes very hot after 10 seconds without any load. If it is powered by 12V, it does not get ...
zhangbs327 Analog electronics
MCU Programmer
Recruiting MCU programmers. If interested, please send your profile to [email=zhongbiao_tong@hotmail.com]zhongbiao_tong@hotmail.com[/email], or 13501711925...
tongzhongbiao Recruitment
IP address problem
[color=rgb(68, 68, 68)][font=Tahoma,]There are two IP addresses here. Which one should I use when connecting to GPRS? The first one is the external network, and the second one is the internal network....
chenbingjy stm32/stm8
How to design a circuit to prevent power supply reverse junction?
[i=s]This post was last edited by dianhang on 2016-8-3 14:23[/i] [size=3]My power input is between 10-24V. I want to use MOS tubes to prevent power reverse junction. How should I design it? [/size]...
dianhang Power technology

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 26  2189  2184  2365  2687  1  45  44  48  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号