EEWORLDEEWORLDEEWORLD

Part Number

Search

SX80M820A3S31836

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 80V, 20% +Tol, 20% -Tol, 820uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size69KB,4 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SX80M820A3S31836 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 80V, 20% +Tol, 20% -Tol, 820uF, Through Hole Mount, ROHS COMPLIANT

SX80M820A3S31836 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompli
ECCN codeEAR99
capacitance820 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
ESR60 mΩ
leakage current0.656 mA
Manufacturer's serial numberSX
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTAPE
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)80 V
ripple current2200 mA
surface mountNO
Delta tangent0.07
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SX
[ For Low Impedance & Low E.S.R ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications
Miniature Size Aluminum
Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 100V
Rate Capacitance Range : 1 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.01 CV or 3(µA) Whichever is greater.
( Measurements shall be Made After a 2 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 6.3
10
16
25
35
50
63
80
100
D.F (%) : 19
16
14
12
10
8
8
7
7
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
Temperature Characteristics : at 120 Hz
WV (V)
:
Impedance : Z - 40°C / Z + 20°C
Case Dia
Load Life
øD
2000
3000
5000
Multiplier for Ripple Current
Frequency(Hz)
~4.4µF
5.6~33µF
34~330µF
331~1000µF
1200µF higher
50
0.30
0.40
0.60
0.65
0.85
120
0.40
0.50
0.70
0.90
0.90
300
0.50
0.60
0.80
0.90
0.95
1K
0.70
0.80
0.90
0.98
0.98
10K
0.80
0.90
0.95
1.00
1.00
100K
1.00
1.00
1.00
1.00
1.00
6.3
10
10
6
16
5
25
4
35
4
50
4
63
4
100
4
Used in switching regulator applications in com-
puters. Especially for high frequency.
Low impedance and E.S.R., high permissible ripple
current at high frequency and highter operation
temperature (-40°C to +105°C).
High Temperature Load Life at 105°C for 2000 ~
5000 Hours
DESCRIPTION
Load Life : At 105°C Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
DIAGRAM OF DIMENSIONS
4.0
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Temperature(°C)
Factor
65
1.80
85
1.50
105
1.00
Dimensions : mm
Vinyl Sleeve
(P.V.C)
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
[ESP32-S2-Kaluga-1 Review] Use of the console component
The installation environment has been set up, and now you can start application development. The DEMO routines should all be runnable on ESP32, but there are compatibility issues on ESP32S2. Some peri...
ID.LODA Domestic Chip Exchange
Simulation study on dynamic performance of 200km/h EMU
Abstract: This paper is a collaborative research work on dynamic simulation of 200km/h EMU conducted by China Academy of Railway Sciences (CARS) and Railway Technical Research Institute (RTRI) of Japa...
frozenviolet Automotive Electronics
In analog signal circuits, what are the benefits of hollowing out the bottom of the relay?
Some netizens said that all the layers under the relay should be hollowed out... So I checked the disassembly video of a domestic instrument: Sure enough, the relay was hollowed out, but in another si...
飞鸿浩劫 PCB Design
Keil C assembly language source code
How to view the assembly language code generated by the C language file in Keil C, thank you!...
神速蜗牛 Embedded System
[Repost with Award] Vishay New Energy, Aerospace/Military Solutions (Awards have been awarded)
[b][font=微软雅黑][size=3][url=https://bbs.eeworld.com.cn/thread-368538-1-1.html]【Award Ceremony】Download VISHAY's new energy and aerospace/military solutions and win exquisite gifts! [/url] -------------...
EEWORLD社区 Discrete Device
Emergency: Are there any quality risks in circuit board repair? How to avoid them?
Should we reject any repaired circuit boards, such as those with a discrete component of a SMD replaced? Questions: 1. Are there any international or national standards that stipulate this repair proc...
风过琴弦 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 671  2128  1709  81  377  14  43  35  2  8 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号