HLMA-PF00-QU011 datasheet, PDF

Datasheet> All Categories > LED optoelectronic/LED> photoelectric> HLMA-PF00-QU011

HLMA-PF00-QU011: DescriptionSingle Color LED, Red, Untinted Nondiffused, 1.525mm, PLASTIC PACKAGE-2; CategoryLED optoelectronic/LED photoelectric; File Size71KB，9 Pages; ManufacturerBroadcom

Download Datasheet Parametric View All

HLMA-PF00-QU011 Overview

Single Color LED, Red, Untinted Nondiffused, 1.525mm, PLASTIC PACKAGE-2

HLMA-PF00-QU011 Parametric

Parameter Name	Attribute value
Maker	Broadcom
package instruction	PLASTIC PACKAGE-2
Reach Compliance Code	compli
color	RED
Configuration	SINGLE
Maximum forward current	0.05 A
Lens type	UNTINTED NONDIFFUSED
Nominal luminous intensity	431.5 mcd
Installation features	SURFACE MOUNT
Number of functions	1
Number of terminals	2
Maximum operating temperature	100 °C
Minimum operating temperature	-40 °C
Optoelectronic device types	SINGLE COLOR LED
total height	2.16 mm
method of packing	TAPE AND REEL 7\"
peak wavelength	635 nm
shape	ROUND
size	1.525 mm
surface mount	YES
perspective	125 deg

Preview

Download Datasheet

View All

HLMA-Qx00, HLMA-Px00 HLMT-Px00 and HLMT-Qx00

Subminiature High Performance AlInGaP LED Lamps

Data Sheet

SunPower Series

HLMA-PF00, HLMA-PG00, HLMA-PH00, HLMA-PL00, HLMA-QF00, HLMA-QG00, HLMA-QH00,

HLMA-QL00, HLMT-PG00, HLMT-PH00, HLMT-PL00, HLMT-QG00, HLMT-QH00, HLMT-QL00

Description

Flat Top Package

The HLMX-PXXX flat top lamps use an untinted, nondif-

fused, truncated lens to provide a wide radiation pattern

that is necessary for use in backlighting applications. The

flat top lamps are also ideal for use as emitters in light

pipe applications.

Features



Subminiature flat top package

Ideal for backlighting and light piping applications



Subminiature dome package

Nondiffused dome for high brightness



Wide range of drive currents



Colors: 590 nm Amber, 605 nm Orange, 615 nm Red-

dish-Orange, 622/626 nm Red, and 635 nm Red



Ideal for space limited applications



Axial leads



Available with lead configurations for surface mount

and through hole PC board mounting

Dome Packages

The HLMX-QXXX dome lamps use an untinted, nondif-

fused lens to provide a high luminous intensity within a

narrow radiation pattern.

Lead Configurations

All of these devices are made by encapsulating LED chips

on axial lead frames to form molded epoxy submini-

ature lamp packages. A variety of package configuration

options is available. These include special surface mount

lead configurations, gull wing, yoke lead, or Z-bend. Right

angle lead bends at 2.54 mm (0.100 inch) and 5.08 mm

(0.200 inch) center spacing are available for through hole

mounting. For more information refer to Standard SMT

and Through Hole Lead Bend Options for Subminiature

LED Lamps data sheet.

Technology

These subminiature solid state lamps utilize one of the

two newly developed aluminum indium gallium phos-

phide (AlInGaP) LED technologies. The HLMT-Devices

are especially effective in very bright ambient lighting

conditions. The colors 590 nm amber, 605 nm orange,

615 nm reddish-orange, 622/626 nm red, and 635 nm red

are available with viewing angles of 15° for the domed

devices and 125° for the flat top devices.

Recommended Resources

What is the impact between power supply noise and high-speed DAC phase noise?

Grain depot humidity detection circuit

Automatic intermittent forward and reverse control circuit for elevator traction machine simulation test

Commonly used supporting equipment for general frequency converters

Programmable power supply circuit

12V, 10A regulated power supply composed of LM305

Please recommend some op amps with full power bandwidth greater than 300kHz and output current of about 1-5A.: The amplification center frequency is required to be 100kHz and the bandwidth is 40kHz. The large signal power supply range should be larger. There are no special requirements for other parameters....; lp328 Analog electronics

Small Problems with 51 MCU: #include sbit LED1=P0^0; sbit KEY1=P2^1; void main() { while(1) { LED1=~KEY1; }; } This is a program I wrote to control a light with a key. As long as you keep pressing the key, the light will stay on...; 44444444444444 MCU

Questions about high frequency square wave inverter power supply: Can anyone tell me how to improve the power factor of a high frequency square wave inverter? I would be very grateful....; xiaomi Power technology

[RVB2601 Creative Application Development] + Music Spectrum: [i=s]This post was last edited by 90houyidai on 2022-6-5 23:27[/i]Project name: [ RVB2601 Creative Application Development] + Music SpectrumAuthor: 90houyidaiProject BackgroundRVB2601 uses Pingtouge's...; 90houyidai XuanTie RISC-V Activity Zone

STM8 EEPROM Experience: For STM8, its internal EEPROM is indeed a good thing, and the price of STM8S103/105 is already very cheap. Of course, it can also be replaced by STM8S003/005, and the price is even cheaper, about 1.2/...; zhaojun_xf stm32/stm8

How do I write a camera application for the 2440Camera interface? Just like the CamTest.exe provided by Samsung SMDK2440: As the title says, my camera is a camera interface. I want to write an application like CamTest.exe provided by Samsung SMDK2440, but I have no idea. Please help me. Do I need to use the program in th...; dengjiescut2006 Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components