EEWORLDEEWORLDEEWORLD

Part Number

Search

FRN0W2J0103AA8

Description
Fixed Resistor - Fusible, 0.5W, 10000ohm, 5% +/-Tol, 350ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size657KB,2 Pages
ManufacturerRoyal Electronic Factory (Thailand) Co., Ltd.
Environmental Compliance  
Download Datasheet Parametric View All

FRN0W2J0103AA8 Overview

Fixed Resistor - Fusible, 0.5W, 10000ohm, 5% +/-Tol, 350ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT

FRN0W2J0103AA8 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerRoyal Electronic Factory (Thailand) Co., Ltd.
package instructionAXIAL LEADED, ROHS COMPLIANT
Reach Compliance Codecompli
ECCN codeEAR99
fuse time60 s
JESD-609 codee3
Manufacturer's serial numberFRN
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package shapeTUBULAR PACKAGE
method of packingAMMO PACK
Rated power dissipation(P)0.5 W
Rated temperature70 °C
resistance10000 Ω
Resistor typeFIXED RESISTOR - FUSIBLE
surface mountNO
technologyMETAL FILM
Temperature Coefficient350 ppm/°C
Terminal surfaceTin (Sn) - with Nickel (Ni) barrie
Terminal shapeWIRE
Tolerance5%
How to perform current detection?
[i=s] This post was last edited by dontium on 2015-1-23 12:40 [/i] I would like to ask all the experts, if I want to detect the current of 4~20ma, what is the appropriate design? The internal resistan...
wstcnsbc1 Analogue and Mixed Signal
Help with MRC p15,0,R0,c0,c0,0
Is the instruction MRC p15,0,R1,c0,c0,0 used to read the ID number of the ARM CPU into the ARM register R1? If so, I have now embedded a .s file with the following assembly content in the EVC environm...
ATT001 Embedded System
What is the use of placing the interrupt flag in the interrupt program?
interrupt[PORT_vector]void PORT1(void){if(P1IFG&BIT0){Delay();if(P1IFG&BIT0){Execution body;P1IFG&=~BIT0;}}}Can this remove jitter? I feel that judging the interrupt flag in the interrupt program can ...
maihy1985 Microcontroller MCU
STM32DAC and PWM clock are not synchronized, please help
I use the internal DAC of the stm32L4 chip to generate a sine wave, and then use the timer's PWM to generate a square wave. However, I found through an oscilloscope that the two waveforms are not sync...
lulongqin12 stm32/stm8
Learn Analog + Learn Operational Amplifier Gain Error Design Guide
[i=s]This post was last edited by dontium on 2015-1-23 11:39[/i] [b][size=2]Operational Amplifier Gain Error Design Guide[/size][/b][size=2]deyisupport./blog/b/signalchain/archive/2013/10/01/51518.asp...
machinnneee Analogue and Mixed Signal
How to place component packages outside the Package Keepin area in Allegro
I set the Package Keepin area when drawing the PCB in Allegro. Now I want to place the DB25 connector on the edge of the PCB. Part of the component needs to go beyond the PCB frame, and of course it a...
文心雕龙7 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1645  2656  2543  9  850  34  54  52  1  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号