EEWORLDEEWORLDEEWORLD

Part Number

Search

51702-10200400CA

Description
Board Connector, 6 Contact(s), Female, Straight, Solder Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size239KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

51702-10200400CA Overview

Board Connector, 6 Contact(s), Female, Straight, Solder Terminal, Guide Pin, Receptacle

51702-10200400CA Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerAmphenol
Reach Compliance Codecompli
Board mount optionsSPLIT BOARD LOCK
body width0.574 inch
subject depth0.5 inch
body length1.25 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact arrangementS4P2
Contact completed and terminatedTIN/LEAD OVER NICKEL
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialTHERMOPLASTIC
Manufacturer's serial number51702
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)1 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.165 inch
Termination typeSOLDER
Total number of contacts6
Evacuation force-minimum value.1668 N
PDM: Rev:P
STATUS:
Released
Printed: Feb 21, 2012
.
I2C interface problem of PIC16F877A
I want to use a PIC16F877A as a slave device of the I2C interface. After writing the program and burning it, I found that the clock at the SCL end could not be input. After a period of time, when I in...
old——Jia Microchip MCU
dsp28335 AD sampling single mode
[p=28, null, left][color=rgb(69, 69, 69)]Three modes are configured: single mode, continuous mode and DMA transfer[/color][/p][p=28, null, left][color=rgb(69, 69, 69)]Single mode calls the acquisition...
fish001 DSP and ARM Processors
How to use circuit to stabilize signal?
I want to stabilize the signal output by the low-frequency power amplifier without using a task chip. Can I use some simple components to stabilize the signal? Please give me some advice! Thank you in...
jackiesh Embedded System
XTR111 4-20mA circuit problem
As shown in the figure below, the official 4-20mA schematic diagram is imitated. Since the microcontroller does not have DA, DAC7512 is used. During the debugging process, it is found that the 5V outp...
zixialong Analogue and Mixed Signal
Purgatory Legends - Battle of Relational Operators
[align=left]There are four types of relational operators: [/align][align=left](1) a b a is greater than b [/align][align=left](3) a=ba is less than or equal to b [/align][align=left](4) a=ba is greate...
梦翼师兄 FPGA/CPLD
Please teach me how to set the high frequency crystal oscillator of msp430F5438
Has anyone used XT2? The registers of 5xx series are quite different from the previous ones. I can't set XT2 as MCLK. The clock register settings are as follows:P5SEL=0x0C; //crystal high ON P5.2.P5.3...
lxcqh2008 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2608  2584  1545  1348  321  53  32  28  7  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号