(forMurata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating from the website of storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
C02E.pdf
05.12.14
Chip Monolithic Ceramic Capacitors
Capacitor Arrays GNM Series
GNM1M2/212
P
GNM214/314
P
s
Features
1. High density mounting due to mounting space saving
2. Mounting cost saving
T
s
Applications
General electronic equipment
L
W
L
W
Part Number
GNM1M2
GNM212
GNM214
GNM314
L
1.37
±0.15
2.0
±0.15
3.2
±0.15
Dimensions (mm)
W
T
P
0.6
±0.1
0.64
±0.05
1.0
±0.15
0.8 +0/-0.15
0.85
±0.1
1.0
±0.1
1.25
±0.15
0.6
±0.1
0.5
±0.05
0.8
±0.1
1.6
±0.15
0.8
±0.1
1.0
±0.1
Temperature Compensating Type
Part Number
LxW
GNM1M
GNM21
GNM31
1.37x1.0
C0G
(5C)
50
(1H)
2.0x1.25
C0G
(5C)
50
(1H)
100
(2A)
3.2x1.6
C0G
(5C)
50
(1H)
10
TC
Rated Volt.
Capacitance, Capacitance Tolerance and T Dimension
10pF(100)
15pF(150)
22pF(220)
27pF(270)
33pF(330)
39pF(390)
47pF(470)
68pF(680)
100pF(101)
150pF(151)
220pF(221)
270pF(271)
330pF(331)
K
K
K
K
K
K
K
K
K
K
K
K
K
0.6(2)
0.6(2)
0.6(2)
0.6(2)
0.6(2)
0.6(2)
0.6(2)
0.6(2)
0.6(2)
0.6(2)
0.6(2)
0.6(4)
0.6(4)
0.6(4)
0.6(4)
0.6(4)
0.6(4)
0.6(4)
0.6(4)
0.6(4)
0.6(4)
0.6(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
The part numbering code is shown in each ( ). The (4) code in T (mm) means number of elements (four).
Dimensions are shown in mm and Rated Voltage in Vdc.
High Dielectric Constant Type GNM1M Series
Part Number
LxW
TC
Rated Volt.
GNM1M
1.37x1.00
X5R
(R6)
16
(1C)
10
(1A)
6.3
(0J)
50
(1H)
X7R
(R7)
25
(1E)
16
(1C)
Capacitance, Capacitance Tolerance and T Dimension
1000pF(102)
2200pF(222)
4700pF(472)
10000pF(103)
22000pF(223)
K, M
K, M
K, M
K, M
K, M
0.6(2)
0.6(2)
0.6(2)
0.6(2)
0.6(2)
Continued on the following page.
52
T
!Note
• This PDF catalog is downloadedand
!CAUTION
(forMurata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating from the website of storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
C02E.pdf
05.12.14
Continued from the preceding page.
Part Number
LxW
TC
Rated Volt.
GNM1M
1.37x1.00
X5R
(R6)
16
(1C)
10
(1A)
6.3
(0J)
50
(1H)
X7R
(R7)
25
(1E)
16
(1C)
Capacitance, Capacitance Tolerance and T Dimension
47000pF(473)
0.10µF(104)
1.0µF(105)
K, M
K, M
K, M
0.8(2)
0.8(2)
0.8(2)
0.8(2)
0.6(2)
The part numbering code is shown in each ( ). The (2) code in T (mm) means number of elements (two).
Dimensions are shown in mm and Rated Voltage in Vdc.
Please refer to Specificaion and Test Methods (2) about 1.0µF products.
High Dielectric Constant Type GNM21 Series
Part Number
LxW
TC
Rated Volt.
GNM21
2.0x1.25
X5R
(R6)
16
(1C)
10
(1A)
50
(1H)
X7R
(R7)
25
(1E)
16
(1C)
Capacitance, Capacitance Tolerance and T Dimension
1000pF(102)
2200pF(222)
4700pF(472)
10000pF(103)
22000pF(223)
47000pF(473)
0.10µF(104)
0.47µF(474)
1.0µF(105)
2.2µF(225)
K, M
K, M
K, M
K, M
K, M
K, M
K, M
K, M
K, M
K, M
0.85(2)
0.85(2)
0.85(4)
0.85(2)
0.6(4)
0.6(4)
0.6(4)
0.6(4)
0.85(4)
0.85(4)
0.85(4)
10
The part numbering code is shown in each ( ). The (2) code in T (mm) means number of elements (two).
Dimensions are shown in mm and Rated Voltage in Vdc.
Please refer to Specificaion and Test Methods (2) about X5R, 10V products.
High Dielectric Constant Type GNM31 Series
Part Number
LxW
TC
Rated Volt.
GNM31
3.2x1.6
X7R
(R7)
100
(2A)
50
(1H)
16
(1C)
X5R
(R6)
10
(1A)
Capacitance, Capacitance Tolerance and T Dimension
220pF(221)
330pF(331)
470pF(471)
680pF(681)
1000pF(102)
1500pF(152)
2200pF(222)
3300pF(332)
4700pF(472)
6800pF(682)
10000pF(103)
K, M
K, M
K, M
K, M
K, M
K, M
K, M
K, M
K, M
K, M
K, M
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
0.8(4)
Continued on the following page.
53
!Note
• This PDF catalog is downloadedand
!CAUTION
(forMurata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating from the website of storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
C02E.pdf
05.12.14
Continued from the preceding page.
Part Number
LxW
TC
Rated Volt.
GNM31
3.2x1.6
X7R
(R7)
100
(2A)
50
(1H)
16
(1C)
X5R
(R6)
10
(1A)
Capacitance, Capacitance Tolerance and T Dimension
15000pF(153)
22000pF(223)
33000pF(333)
47000pF(473)
68000pF(683)
0.10µF(104)
1.0µF(105)
K, M
K, M
K, M
K, M
K, M
K, M
K, M
0.8(4)
0.8(4)
0.8(4)
1.0(4)
1.0(4)
1.0(4)
0.85(4)
The part numbering code is shown in each ( ). The (4) code in T (mm) means number of elements (four).
Dimensions are shown in mm and Rated Voltage in Vdc.
10
54
!Note
• This PDF catalog is downloadedand
!CAUTION
(forMurata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating from the website of storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
C02E.pdf
05.12.14
GNM Series Specifications and Test Methods (1)
Specifications
No.
Item
Temperature
Compensating Type
5C : –55 to +125°C
Test Method
High Dielectric Type
R7 : –55 to +125°C
R6 : –30 to +85°C
The rated voltage is defined as the maximum voltage which
may be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage, V
P-P
or V
O-P
,
whichever is larger, should be maintained within the rated
voltage range.
Visual inspection
Using calipers
No failure should be observed when 300% of the rated voltage
(5C) or 250% of the rated voltage (R7) is applied between the
terminations for 1 to 5 seconds, provided the charge/discharge
current is less than 50mA.
The insulation resistance should be measured with a DC
voltage not exceeding the rated voltage at 25°C and 75%RH
max. and within 2 minutes of charging.
The capacitance/Q/D.F. should be measured at 25°C at the
frequency and voltage shown in the table.
10V
0.035
max.
6.3V
0.05
max.
Char.
Item
Frequency
Voltage
5C
1T0.1MHz
0.5 to 5Vrms
R7
1T0.1kHz
1.0T0.2Vrms
1
Operating
Temperature
Range
2
Rated Voltage
See the previous pages.
3
4
Appearance
Dimensions
No defects or abnormalities
Within the specified dimensions
5
Dielectric Strength
No defects or abnormalities
6
7
Insulation
Resistance
Capacitance
More than 10,000MΩ or 500Ω · F
(Whichever is smaller)
Within the specified tolerance
30pF min. : QU1000
30pF max. :
QU400+20C
C : Nominal
Capacitance (pF)
Temp. Reference Cap.
Char.
Range
Temp.
Change
–55°C
R7
to +125°C
Within
25°C
T15%
–55°C
R6
to +85°C
Char. 25V min. 16V
0.025 0.035
R7, R6
max.
max.
8
Q/
Dissipation Factor
(D.F.)
10
Capacitance
Change
Within the
specified tolerance
(Table A)
9
Capacitance
Temperature
Characteristics
Temperature
Coefficent
Within the
specified tolerance
(Table A)
The capacitance change should be measured after 5 min. at
each specified temperature stage.
(1) Temperature Compensating Type
The temperature coefficient is determined using the capaci-
tance measured in step 3 as a reference. When cycling the
temperature sequentially from step1 through 5, the capacitance
should be within the specified tolerance for the temperature
coefficient and capacitance change as Table A.
The capacitance drift is calculated by dividing the differences
between the maximum and minimum measured values in the
steps 1, 3 and 5 by the cap. value in step 3.
Step
1
2
3
4
5
Temperature (°C)
25T2
–55T3 (for 5C/R7), –30T3 (for F5)
25T2
125T3 (for 5C/R7), 85T3 (for F5)
20T2
Capacitance
Drift
Within
T0.2%
or
T0.05pF
(Whichever is
larger.)
(2) High Dielectric Constant Type
The ranges of capacitance change compared with the above
25°C value over the temperature ranges shown in the table
should be within the specified ranges.
Solder the capacitor to the test jig (glass epoxy board) shown in
Fig.1 using a eutectic solder. Then apply 5N force in parallel with
the test jig for 10T1 sec.
The soldering should be done either with an iron or using the
reflow method and should be conducted with care so that the
soldering is uniform and free of defects such as heat shock.
Type
GNM1M2
GNM212
GNM214
GNM314
a
0.5
0.4
0.6
0.8
b
1.6
1.8
2.0
2.5
Fig. 1
Continued on the following page.
No removal of the terminations or other defect should occur.
GNMpp4
b
a
c
GNMpp2
b
a
c
d
10
Adhesive Strength
of Termination
Solder resist
Copper foil
d
Solder resist
Copper foil
c
0.32
0.15
0.25
0.4
d
0.32
0.5
0.25
0.4
(in mm)
55
!Note
• This PDF catalog is downloadedand
!CAUTION
(forMurata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating from the website of storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
C02E.pdf
05.12.14
GNM Series Specifications and Test Methods (1)
Continued from the preceding page.
Specifications
No.
Item
Temperature
Compensating Type
No defects or abnormalities
Within the specified tolerance
30pF min. : QU1000
30pF max. :
QU400+20C
C : Nominal
Capacitance (pF)
Test Method
High Dielectric Type
Solder the capacitor to the test jig (glass epoxy board) in the
same manner and under the same conditions as (10). The
capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each 3 mutually perpendicular
directions (total of 6 hours).
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 2 using a eutectic solder.
Then apply a force in the direction shown in Fig. 3 for 5T1 sec.
The soldering should be done either with an iron or using the
reflow method and should be conducted with care so that the
soldering is uniform and free of defects such as heat shock.
100
Appearance
Capacitance
11
Vibration
Resistance
Q/D.F.
Char. 25V min. 16V
0.025 0.035
R7, R6
max.
max.
10V
0.035
max.
6.3V
0.05
max.
No cracking or marking defects should occur.
#GNMpp4
40
#GNMpp2
40
`
`
5.0
a
b
100
5.0
a
b
20
12
Deflection
1.0
c
1.0
50 Pressurizing
speed : 1.0mm/sec.
Pressurize
c
d
d
R230
t=0.8mm
Flexure :
V1
10
Type
GNM1M2
GNM212
GNM214
GNM314
a
2.0T0.05
2.0T0.05
2.0T0.05
2.5T0.05
b
0.5T0.05
0.6T0.05
0.7T0.05
0.8T0.05
Fig. 2
c
d
0.32T0.05 0.32T0.05
0.5T0.05 0.5T0.05
0.3T0.05 0.2T0.05
0.4T0.05 0.4T0.05
(in mm)
Capacitance meter
45
45
Fig. 3
13
Solderability of
Termination
75% of the terminations are to be soldered evenly and
continuously.
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at
80 to 120°C for 10 to 30 seconds. After preheating, immerse in
eutectic solder solution for 2T0.5 seconds at 230T5°C or
Sn-3.0Ag-0.5Cu solder solution for 2T0.5 seconds at 245T5°C.
Resistance to
Soldering Heat
Appearance
Capacitance
Change
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within
T2.5%
or
T0.25pF
(Whichever is
larger)
30pF min. : QU1000
30pF max. :
QU400+20C
C : Nominal
Capacitance (pF)
Preheat the capacitor at 120 to 150°C for 1 minute. Immerse
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder
solution at 270T5°C for 10T0.5 seconds. Let sit at room
temperature for 24T2 hours, then measure.
10V
0.035
max.
6.3V
0.05
max.
• Initial measurement for high dielectric constant type
Perform a heat treatment at 150+0/-10°C for one hour and
then let sit for 24T2 hours at room temperature.
Perform the initial measurement.
R7, R6 : Within
T7.5%
14
Q/D.F.
Char. 25V min. 16V
0.025 0.035
R7, R6
max.
max.
I.R.
Dielectric
Strength
More than 10,000MΩ or 500Ω · F (Whichever is smaller)
Shenzhen Baohuaao Electronics Co., Ltd. is a large-scale aluminum electrolytic capacitor manufacturer engaged in the technical research and development, design, manufacturing and sales of high-quality...
Send a copy of the information of the two-axis SPI communication TSSOP20 package motion control chip mpc02t, including instructions and C language program...
I use Wenting's TDS560 emulator to debug TI's F2812 development board and DSP/BIOS system. CCS always crashes when it runs, but there is no problem debugging non-DSP/BIOS programs. I searched for post...
Error prompt 100ask24x0.c: In function `board_init': 100ask24x0.c:106: warning: implicit declaration of function `_asm_' 100ask24x0.c:110: error: syntax error before ':' token 100ask24x0.c:135: error:...
:Sweat: I want to make a circuit that converts 220V to 380V, and then doubles the voltage to rectify it. The circuit is the most common, but I don’t know how to choose the electrolytic capacitor. I wo...
1. Discussion on the design of printed circuit component layout structure For an instrument with excellent performance, in addition to selecting high-quality components and reasonable circuits, the ...
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
The principles to be followed are as follows:
(1) In terms of component layout, related components should be placed as close as possible. For example, clock generators, crystal oscillat...[Details]
Abstract: Based on the analysis of the characteristics of the IRIG-B (DC) code type, a design method for IRIG-B (DC) time code decoding is proposed. This method consists of a small number of periph...[Details]
Traditional synthesis techniques are increasingly unable to meet the needs of today's very large and complex FPGA designs implemented in 90nm and below process nodes. The problem is that traditio...[Details]
Some people think: as long as the program runs well, it doesn't matter how the original program is written. But this is absolutely not the case. Software is not completed in one go, and it is neces...[Details]
I. Introduction
The use of electronics in cars dates back to the early 20th century when electric starters replaced hand cranks. Automotive electronics became popular in the 1960s with the...[Details]
1 Introduction
In order to cope with the energy crisis and slow down global warming, many countries have begun to pay attention to energy conservation and emission reduction and the de...[Details]
PID is proportional differential adjustment. You can refer to the detailed introduction in the automatic control course for details! The positive action and the negative action in temperature contr...[Details]
There are two main ways to measure temperature: one is the traditional contact measurement, and the other is
non-contact measurement represented by
infrared temperature measurement
. Tradit...[Details]
The Challenge:
Protect historical relics by monitoring environmental factors without affecting their original appearance.
The Solution:
Developed a monitoring system for the...[Details]
1 Introduction
With the continuous development of electronic technology, automotive electronic technology has also developed rapidly. The number of various electronic control units on automobi...[Details]
UPS is an uninterruptible power supply (UPS). This device can ensure that after a power outage in the computer system, users can continue to work for a period of time and save files urgently, witho...[Details]
In the field of video surveillance, video compression encoding formats have evolved from M-JPEG, H.263, MPEG4 to H.264. Currently, H.264 is the mainstream compression algorithm. Its biggest advantage ...[Details]
The system is a wireless email terminal based on WLAN (Wireless Loeal Area Network). Users can easily input email content on the touch screen with a stylus, and send and receive emails throug...[Details]
Buy&Sell
京公网安备 11010802033920号
EEWORLD
