EEWORLDEEWORLDEEWORLD

Part Number

Search

M2023LL2G26-A

Description
Toggle Switch
CategoryMechanical and electronic products    switch   
File Size631KB,7 Pages
ManufacturerNDK
Websitehttp://www.ndk.com/en/
Environmental Compliance
Download Datasheet Parametric View All

M2023LL2G26-A Overview

Toggle Switch

M2023LL2G26-A Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerNDK
Reach Compliance Code_compli
Manufacturer's serial numberM
Switch typeTOGGLE SWITCH
Series M
A
Miniature Toggles
General
Specifications
Electrical Capacity (Resistive Load)
Power Level (silver):
6A @ 125V AC & 3A @ 250V AC
4A @ 30V DC for On-None-On & On-None-Off; 3A @ 30V DC for all other circuits
Logic Level (gold):
0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Logic/Power Level (gold over silver):
Combines silver & gold ratings
Note: Find additional explanation of dual rating & operating range in Supplement section.
Contact Resistance:
10 milliohms maximum for silver; 20 milliohms maximum for gold
Insulation Resistance:
1,000 megohms minimum @ 500V DC
Dielectric Strength:
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts and case for 1 minute minimum
Mechanical Life:
100,000 operations minimum; 50,000 operations minimum for flat, locking & splashproof devices
Electrical Life:
25,000 operations minimum for silver; 50,000 operations minimum for gold;
50,000 operations minimum for silver at 3A @ 125V AC
Angle of Throw:
25°
Toggle:
Bushing:
Case:
Movable Contactor:
Movable Contacts:
Stationary Contacts:
Brass with chrome plating
Frame:
Stainless steel
Brass with nickel plating
Support Bracket:
Brass with tin plating
Diallyl phthalate resin (UL94V–0)
Phosphor bronze with silver or gold plating
Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A)
Silver with silver plating (code W); copper or brass with gold plating (code G);
or silver with gold plating (code A)
Terminals:
Copper or brass with silver plating; or copper or brass with gold plating
Pushbuttons
Rockers
Toggles
Other Ratings
Programmable Illuminated PB
Materials & Finishes
Rotaries
Keylocks
Slides
Environmental Data
Operating Temp Range:
–30°C through +85°C (–22°F through +185°F)
Humidity:
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Vibration:
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
Shock:
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Sealing:
Splashproof bushing options B3, D3, D8, L3, & L8, which have o-rings inside & outside the
bushing, meet IP67 of IEC60529 Standards.
Mounting Torque:
3.0Nm (26.55 lb
in) double nut for large bushing;
1.5Nm (13 lb
in) double nut & 0.7Nm (6 lb
in) single nut for all other bushings
Soldering:
Wave Soldering (PC version) for Gold: See Profile A in Supplement section.
Manual Soldering for Gold: See Profile A in Supplement section.
Wave Soldering (PC version) for Silver: See Profile B in Supplement section.
Manual Soldering for Silver: See Profile B in Supplement section.
Note: Lever must be in OFF (center) position while soldering.
Cleaning:
These devices are not process sealed. Hand clean locally using alcohol based solution.
Tactiles
Installation
Tilt
Processing
Touch
Indicators
Standards & Certifications
Supplement
Flammability Standards:
UL94V–0 for case
UL: File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL” before dash in part number to order UL recognized switch.
All models recognized at 6A @ 125V AC, 3A @ 250V AC or 0.4VA maximum @ 28V DC maximum.
CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” before dash in part number to order CSA certified switch.
All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA maximum @ 28V maximum.
Accessories
A48
www.nkk.com
DSP 3.3V and 1.8V power-up sequence
The power supplies required by DSP are 3.3V and 1.8V. If different power supplies are used, are there any special requirements for the power-on sequence?...
安_然 DSP and ARM Processors
The forum finally has an Altera event
The forum finally has an Altera event. I am so happy. However, the last question is not mentioned in the article, but I found it in this article [b]Altera SoC FPGA: The Importance of Architecture[/b] ...
白丁 Talking
What kind of sensor is 2 PIN current loop sensor?
The original text is described as follows: 2pin current loop sensors (ABS-type with 7/14mA output signal). Could you please tell me the principle or information of this sensor? Thank you...
bdhrui Analog electronics
DSP Error Induction
[table=98%] [tr][td][color=#000000]Summary of common errors encountered during DSP application development: 1.warning: entry point symbol _c_int00 undefined When using C to write DSP programs, the ent...
Jacktang DSP and ARM Processors
Nantong Fujitsu: The scale of packaging and testing will reach 9 billion units next year
Nantong Fujitsu: The scale of packaging and testing will reach 9 billion units next year2006-8-31 Source: Hits: 79  Nantong Fujitsu is the first integrated circuit manufacturing company in China to tr...
fighting Analog electronics
MicroPython standard library usocke
usocket – socket module usocket – socket module BSD socket interface CPython corresponding module for comparison Socket address format The following function uses the ipv4 format (address: port) netwo...
dcexpert MicroPython Open Source section

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1417  744  691  1147  1238  29  15  14  24  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号