CAT24C128
128-Kb I
2
C CMOS Serial EEPROM
FEATURES
■
Supports Standard and Fast I
2
C Protocol
■
1.8V to 5.5V Supply Voltage Range
■
64-Byte Page Write Buffer
■
Hardware Write Protection for entire memory
■
Schmitt Triggers and Noise Suppression Filters
DEVICE DESCRIPTION
The CAT24C128 is a 128-Kb Serial CMOS EEPROM,
internally organized as 16,384 words of 8 bits each.
It features a 64-byte page write buffer and supports
both the Standard (100 kHz) as well as Fast (400 kHz)
I
2
C protocol.
Write operations can be inhibited by taking the WP pin
High (this protects the entire memory).
on I
2
C Bus Inputs (SCL and SDA).
■
Low power CMOS technology
■
1,000,000 program/erase cycles
■
100 year data retention
■
Industrial and Extended temperature range
■
RoHS-compliant 8-lead PDIP, SOIC, TSSOP and
UDFN packages
For additional packages and Ordering
Information details, see page 15.
PIN CONFIGURATION
PDIP (L)
SOIC (W)
TSSOP (Y)
UDFN (HU3)
A0
A1
A2
VSS
1
2
3
4
8
7
6
5
VCC
WP
SCL
SDA
FUNCTIONAL SYMBOL
VCC
SCL
A2, A1, A0
WP
CAT24C128
SDA
For the location of Pin 1, please consult the
corresponding package drawing.
PIN FUNCTIONS
VSS
A
0
, A
1
, A
2
SDA
SCL
WP
V
CC
V
SS
Device Address Inputs
Serial Data Input/Output
Serial Clock Input
Write Protect Input
Power Supply
Ground
* Catalyst carries the I
2
C protocol under a license from the Philips Corporation.
© 2008 SCILLC. All rights reserved.
Characteristics subject to change without notice.
1
Doc. No. MD-1103, Rev. K
CAT24C128
ABSOLUTE MAXIMUM RATINGS
(1)
Storage Temperature
Voltage on Any Pin with Respect to Ground
(2)
RELIABILITY CHARACTERISTICS
(3)
Symbol
N
END(4)
T
DR
Parameter
Endurance
Data Retention
Min
1,000,000
100
Units
Program/ Erase Cycles
Years
-65°C to +150°C
-0.5 V to +6.5 V
D.C. OPERATING CHARACTERISTICS
V
CC
= 1.8 V to 5.5 V, T
A
= -40°C to +125°C, unless otherwise specified.
Symbol Parameter
I
CCR
I
CCW
I
SB
I
L
V
IL
V
IH
V
OL1
V
OL2
Read Current
Write Current
Standby Current
I/O Pin Leakage
Input Low Voltage
Input High Voltage
Output Low Voltage V
CC
< 2.5 V, I
OL
= 3.0mA
Output Low Voltage V
CC
< 2.5 V, I
OL
= 1.0mA
Test Conditions
Read, f
SCL
= 400kHz
Write, f
SCL
= 400kHz
All I/O Pins at GND or V
CC
Pin at GND or V
CC
T
A
= -40°C to +85°C
T
A
= -40°C to +125°C
T
A
= -40°C to +85°C
T
A
= -40°C to +125°C
-0.5
Min
Max
1
3
1
2
1
2
V
CC
x 0.3
0.4
0.2
V
CC
x 0.7 V
CC
+ 0.5
Units
mA
mA
μA
μA
V
V
V
V
PIN IMPEDANCE CHARACTERISTICS
V
CC
= 1.8 V to 5.5 V, T
A
= -40°C to +125°C, unless otherwise specified.
Symbol
C
IN(3)
C
IN(3)
I
WP(5)
Parameter
SDA I/O Pin Capacitance
Input Capacitance (other pins)
WP Input Current
Conditions
V
IN
= 0 V
V
IN
= 0 V
V
IN
< V
IH
V
IN
> V
IH
Note:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this speci-
fication is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
(2) The DC input voltage on any pin should not be lower than -0.5 V or higher than V
CC
+ 0.5 V. During transitions, the voltage on any pin may
undershoot to no less than -1.5 V or overshoot to no more than V
CC
+ 1.5 V, for periods of less than 20 ns.
(3) These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100
and JEDEC test methods.
(4) Page Mode, V
CC
= 5 V, 25°C
(5) When not driven, the WP pin is pulled down to GND internally. For improved noise immunity, the internal pull-down is relatively strong;
therefore the external driver must be able to supply the pull-down current when attempting to drive the input HIGH. To conserve power, as
the input level exceeds the trip point of the CMOS input buffer (~ 0.5 x VCC), the strong pull-down reverts to a weak current source.
Max
8
6
200
1
Units
pF
pF
μA
μA
Doc. No. MD-1103, Rev. K
2
© 2008 SCILLC. All rights reserved.
Characteristics subject to change without notice.
CAT24C128
POWER-ON RESET (POR)
The CAT24C128 incorporates Power-On Reset
(POR) circuitry which protects the device against
powering up in the wrong state.
The CAT24C128 will power up into Standby mode
after V
CC
exceeds the POR trigger level and will power
down into Reset mode when V
CC
drops below the POR
trigger level. This bi-directional POR feature protects
the device against ‘brown-out’ failure following a
temporary loss of power.
I
2
C BUS PROTOCOL
The I
2
C bus consists of two ‘wires’, SCL and SDA. The
two wires are connected to the V
CC
supply via pull-up
resistors. Master and Slave devices connect to the 2-
wire bus via their respective SCL and SDA pins. The
transmitting device pulls down the SDA line to ‘transmit’
a ‘0’ and releases it to ‘transmit’ a ‘1’.
Data transfer may be initiated only when the bus is not
busy (see A.C. Characteristics).
During data transfer, the SDA line must remain stable
while the SCL line is HIGH. An SDA transition while
SCL is HIGH will be interpreted as a START or STOP
condition (Figure 1). The START condition precedes all
commands. It consists of a HIGH to LOW transition on
SDA while SCL is HIGH. The START acts as a ‘wake-up’
call to all receivers. Absent a START, a Slave will not
respond to commands. The STOP condition completes
all commands. It consists of a LOW to HIGH transition
on SDA while SCL is HIGH.
Device Addressing
The Master initiates data transfer by creating a START
condition on the bus. The Master then broadcasts an
8-bit serial Slave address. The first 4 bits of the Slave
address are set to 1010, for normal Read/Write opera-
tions (Figure 2). The next 3 bits, A
2
, A
1
and A
0
, select
one of 8 possible Slave devices and must match the
state of the external address pins. The last bit, R/W,
specifies whether a Read (1) or Write (0) operation is
to be performed.
Acknowledge
After processing the Slave address, the Slave responds
with an acknowledge (ACK) by pulling down the SDA
line during the 9
th
clock cycle (Figure 3). The Slave will
also acknowledge all address bytes and every data byte
presented in Write mode. In Read mode the Slave shifts
out a data byte, and then releases the SDA line during
the 9
th
clock cycle. As long as the Master acknowl-
edges the data, the Slave will continue transmitting. The
Master terminates the session by not acknowledging
the last data byte (NoACK) and by issuing a STOP
condition. Bus timing is illustrated in Figure 4.
PIN DESCRIPTION
SCL:
The Serial Clock input pin accepts the Serial Clock
generated by the Master.
SDA:
The Serial Data I/O pin receives input data and
transmits data stored in EEPROM. In transmit mode, this
pin is open drain. Data is acquired on the positive edge,
and is delivered on the negative edge of SCL.
A
0
, A
1
and A
2
:
The Address pins accept the device
address. When not driven, these pins are pulled LOW
internally.
WP:
The Write Protect input pin inhibits all write opera-
tions, when pulled HIGH. When not driven, this pin is
pulled LOW internally.
FUNCTIONAL DESCRIPTION
The CAT24C128 supports the Inter-Integrated Circuit
(I
2
C) Bus data transmission protocol, which defines a
device that sends data to the bus as a transmitter and a
device receiving data as a receiver. Data flow is controlled
by a Master device, which generates the serial clock
and all START and STOP conditions. The CAT24C128
acts as a Slave device. Master and Slave alternate as
either transmitter or receiver. Up to 8 devices may be
connected to the bus as determined by the device ad-
dress inputs A
0
, A
1
, and A
2
.
Doc. No. MD-1103, Rev. K
4
© 2008 SCILLC. All rights reserved.
Characteristics subject to change without notice.
京公网安备 11010802033920号
EEWORLD
