290-16.0M-13-25GP datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> 290-16.0M-13-25GP

290-16.0M-13-25GP: DescriptionParallel - Fundamental Quartz Crystal, 16MHz Nom, SMD, 4 PIN; CategoryPassive components Crystal/resonator; File Size125KB，2 Pages; ManufacturerOscilent; Websitehttp://www.oscilent.com; Environmental Compliance

Download Datasheet Parametric View All

290-16.0M-13-25GP Overview

Parallel - Fundamental Quartz Crystal, 16MHz Nom, SMD, 4 PIN

290-16.0M-13-25GP Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Oscilent
package instruction	SMD, 4 PIN
Reach Compliance Code	compli
Other features	BULK
Crystal/Resonator Type	PARALLEL - FUNDAMENTAL
Drive level	0.01 µW
frequency stability	0.003%
frequency tolerance	25 ppm
load capacitance	13 pF
Installation features	SURFACE MOUNT
Nominal operating frequency	16 MHz
Maximum operating temperature	50 °C
Minimum operating temperature
physical size	L6.0XB3.5XH1.0 (mm)/L0.236XB0.138XH0.039 (inch)
Series resistance	50 Ω
surface mount	YES

Preview

Download Datasheet

View All

Oscilent Corporation | 290

1 of 2

SMD Quartz Crystal

Series Number

Package

Description

Last Modified

290

FEATURES

- Seam welded metal lid / ceramic package

- 1.2mm max. low profile

- Tight stability / High reliability

- Wide frequency range

- Tape and Reel

6 X 3.5

SMD Quartz Crystal

Jun. 25 2003

OPERATING CONDITIONS / ELECTRICAL CHARACTERISTICS

PARAMETERS

Frequency Range

Frequency Tolerance

Frequency Stability

Operating Temperature

Storage Temperature

Shunt Capacitance

Load Capacitance

Equivalent Series Resistance

Mode of Oscillation

Drive Level

@ 25ºC

Ta = -10 +70ºC

OPR

STG

(Customer Specified)

10.00 ~ 40.00 MHz

CHARACTERISTICS

10.00 ~ 40.00

±10 ~ ±50

±10 ~ ±100

-10 ~ +60 (-40 ~ +85 optional)*

-40 ~ +85

7.0 max.

16, 20, 30, Series

50 max.

Fundamental

0.01 ~ 1000

UNITS

MHz

PPM

ºC

Ohm

µW

* Consult Oscilent for available variations of temperature and stability

PART NUMBER GUIDE

Series

Number

Frequency

Load Capacitance Tolerance @ +25oC

Tolerance Over

Temp ( oC )

Operating

Temp ( oC )

Packaging**

290

Oscilent

6 x 3.5 SMD

- 12.0M

See table below for

standard freq. and

enter here

e.g.

12.0M for 12.000

MHz

OR enter any

desire frequency.

- SR

Enter desired

capacitance here.

See table below for

standard load

capacitance

e.g.

-20 for 20pF or

Enter SR for

Series.

- 05

Blank * = ±30 PPM

or Fill in E.G

05 = ±5 PPM

25 = ±25 PPM

Avail. = ±5 ~ ±100

Blank*

= ±50 PPM

±30 PPM

±25 PPM

±20 PPM

±10 PPM

±100 PPM

0~+50

-10~+60

-20~+70

-30~+80

-40~+85

- TR

Blank* = Bulk

TR = Tape/Reel

NOTE:

Deviations on all parameters available. Please consult Oscilent for details.

DEFINITIONS:

Click on the characteristic names above for definitions of that particular characteristic.

*STANDARDS:

"Blank" part number selections indicate standard variables for that particular characteristic.

**PACKAGING:

Click on the packaging name above for tape/reel specifications

STANDARD FREQUENCIES / LOAD CAPACITANCE

AVAILABLE

FREQUENCY

(MHz)

12.000

14.31818

16.000

18.432

19.6608

LOAD (pF)

Series

Std.

FOR GUIDE ONLY /

OTHER FREQ/LOADS

Recommended Resources

Light control switch relay circuit diagram

Russacll Hobbs steam iron circuit diagram

DDZ-1 regulator external wiring

Delta motor zero sequence voltage phase failure protection circuit

Opto-isolator input protection circuit

barcode reading circuit

[Solved] The data read out by CS5513 cannot reach the maximum value: [i=s] This post was last edited by Tobey on 2017-4-18 09:29 [/i] Hardware: stm32f103 cs5513 Development environment: keil v5.20 Problem: Based on the stm32f103 chip, the ADC value of CS5513 is read. C...; Tobey stm32/stm8

How to call the close button in the upper right corner of the software developed with evc: I use SHDoneButton(m_hWnd, SHDB_HIDE) to hide the OK button in the upper right corner and show the Close button. Now I want to save some information when the Close button is clicked. What is the relat...; mikeylover Embedded System

FreeRTOS Learning Notes (5) Interrupts and Task Switching: [i=s]This post was last edited by cruelfox on 2018-9-10 07:54[/i] After FreeRTOS has the memory resource of the task - the stack management mechanism, can perform context switching of CPU execution ac...; cruelfox MCU

STM8 continues to ask stupid questions about null instructions: STM8S903K3 chip, what is the format of ST chip null instruction?I wrote (NOP); no, asm("nop") doesn't work either. Can any expert teach me, thank you!...; xb123 stm32/stm8

Verilog_Tutorial PPT + 44 kinds of electronic self-made PDF + ADDA materials (modified, no core coins!): Free download!!!! :loveliness:[[i]This post was last edited by cfg on 2011-8-14 16:58[/i]]...; cfg Electronics Design Contest

A little problem with Modbus: How to implement the 3.5 character timeout judgment when implementing Modbus on a single chip? If the time interval between each call for test data by the host computer is more than 1 second, can this...; vernusian Embedded System

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components