Ruthenium oxide dielectric offers superior resistance
to the elements.
3) Electrodes not corroded by soldering
Thick film makes the electrodes very strong.
4) Leading the world in development and mass produc-
tion.
Since start of production in 1982 (first in the wold), this
component has established a solid reputation as a
general–purpose chip resistor.
5) ROHM resistors have approved ISO–9001 certifica-
tion.
Design and specifications are subject to change with-
out notice. Carefully check the specification sheet be-
fore using or ordering it.
!Ratings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70
°C
.
100
80
60
40
20
0
Specifications
0.125W (1 / 8W)
[0.100W (1 / 10W)]
∗
at 70°C
POWER LOAD (%)
– 55
0
70
100
155
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the maximum operating voltage, the voltage rating
is equal to the maximum operating voltage.
E: Rated voltage (V)
E = P× R
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
Operating temperature
* At power rating of 0.1W, maximum overload voltage and maximum intermittent overload voltage are 300V.
Max. operating voltage
150V
200V
(300V)
∗
Max. overload voltage
Max. intermittent overload voltage 200V
(300V)
∗
See Table 1.
– 55
°C
to + 155
°C
MCR10
Resistors
Jumper type
Resistance
Rated current
Peak current
Max. 50mΩ
2A
10A
J ( ± 5%)
Table 1
Resistance tolerance
F ( ± 1%)
Resistance range
(Ω)
10
≤
R
≤
2.2M (E24,96)
1.0
≤
R
<
2.2
2.2
≤
R
<
10
10
≤
R
<
10M
(E24)
(E24)
(E24)
Resistance temperature coefficient
(ppm /
°C)
± 100
500 ± 350
± 500
± 200
Operating temperature – 55°C to + 155°C
!Before
using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
MCR10
Resistors
!Characteristics
Characteristics
DC resistance
Resistance temperature
characteristics
Short time overload
±
(2.0% + 0.1Ω)
Specifications
Chip resistance
Jumper type
F:
±
1%
J:
±
5%
Max. 50mΩ
Test method
JIS C 5202 5.1
Applied voltage: A
JIS C 5202 5.2
Test conditions: + 25 / – 55 / + 25 / + 125°C
JIS C 5202 5.5
Rated voltage (current):
×
2.5, 5s.
Maximum overload voltage: 200V
JIS C 5202 5.6
Test voltage: 100V, 1min.
Assembled state
Metal block
observation
point A
Insulation plate
See Table 1.
Max. 50mΩ
Min. 1,000MΩ between terminal and board
Insulation resistance
Test resistor
Metal plate
Observation Insulation
sheath
R 0.5
point B
Spring-loaded
pressure
Withstand voltage
Do not damage insulation or cause a short circuit.
±
(5.0% + 0.1Ω)
JIS C 5202 5.7
Test voltage: 500V
JIS C 5202 5.8
Rated voltage (current):
×
2.5
(1s: ON – 25s: OFF)
×
10,000cyc.
JIS C 5202 6.1
JIS C 5202 6.4
Soldering conditions: 260
±
5°C
Soldering time: 10
±
1s.
JIS C 5202 6.5
Rosin methanol: (25%WT)
Soldering conditions: 235
±
5°C
Soldering time: 2.0
±
0.5s.
JIS C 5202 7.2
155°C
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.10
Rated voltage (current), 70°C
1.5h: ON – 0.5h: OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.9
Rated voltage (current), 60°C, 90%RH
1.5h: ON – 0.5h: OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.5
85°C, 85%RH
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.4
Test temperature: – 55°C to + 125°C 100cyc.
JIS C 5202 6.9
Room temperature, static immersion, 1 min.
Solvent: Isopropyl alcohol
Intermittent overload
Terminal strength
(against bending of circuit board)
Resistance to soldering heat
Max. 50mΩ
±
(1.0% + 0.05Ω)
Max. 50mΩ
There must be no mechanical damage.
±
(1.0% + 0.05Ω)
Max. 50mΩ
Outside must not be noticeably damaged.
95% of terminal surface must be covered by
new soldering, and there must be
no soldering corrosion.
Solderability
Resistance to dry heat
±
(3.0% + 0.1Ω)
Max. 100mΩ
Endurance
(under load in damp environment)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Endurance
(steady state)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Resistance to humidity
(steady state)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Temperature cycling
±
(1.0% + 0.05Ω)
Max. 50mΩ
Resistance to solvents
Max. 50mΩ
±
(0.5% + 0.05Ω)
Markings must not be dissolved away.
MCR10
Resistors
!External
dimensions
(Units: mm)
0.4 ± 0.2
No.
0.4 ± 0.2
2.0 ± 0.1
0.55 ± 0.1
Material
Thick dielectric glaze of ruthenium
(only silver used for jumper)
Thick film of palladium-silver for primary electrode
Nickel-coated secondary electrode
External electrode coated with tin and lead
Alumina substrate
1.25 ± 0.1
Overcoating
!Packaging
Reel
Taping
P
0
P
2
P
1
φD
0
E
F
B
0
08
06
04
02
02
04
06
08
W
A
B
D
A
0
Heat crimp cover/Tape
Thick paper (Underside paper tape) Chip resistor Square punchout hole
In the past year, China's IC industry has been quite turbulent, with news of mergers and acquisitions coming one after another. Intersil acquired Panda Microelectronics, MediaTek acquired Aoste, Morni...
RT, according to AD official manual, the board also uses the schematic diagram of the official evaluation board, using SPI serial interface, the main initialization procedure is as follows, there is n...
Hello everyone, I am using 24lc256 eeprom. Byte write/read are fine, but page write has problems. Can anyone help me? Thanks. According to the timing diagram, there should be the following 7 steps: 1)...
Adding register level to the combinational logic to form a pipeline reduces the generation and propagation of signal glitches, thereby reducing the dynamic power consumption of FPGA. The power consump...
[10 Typical Laboratory Circuit Recommendations] 7: This circuit provides a simple, highly integrated temperature monitor solution that can interface with a 4 mA to 20 mA host controller. Since most of...
How can I download programs into STM8 through the serial port like STM32?Can't I use the FLASHLoader to download programs after setting the BOOT?I tested it but it doesn't work on STM8? The manual say...
ZTE,
caught
in the vortex of
the US ban on the sale
of chips
, has sounded the alarm for China's information technology industry and revealed China's "chip disease". Let's follow the ...[Details]
For STM32, there are two ways to reset the software: 1) Use the official software library The system reset function is directly provided in the stm32f10x_nvic.c file of the official software li...[Details]
In the actual project development process, it is common to encounter modifications to the hardware circuit, and then the modified part requires the modification of the driver. Thinking about the comi...[Details]
1.MAX31865 (1 Introduction The MAX31865 is an easy-to-use thermistor-to-digital converter optimized for platinum resistance temperature detectors (RTDs). External resistors set the RTD sensitivity, a...[Details]
introduction In the general project development process, two or more microcontrollers are often required to communicate to complete data transmission. For example, a quadcopter wirelessly transmits d...[Details]
1. Initial understanding of FSMC: FSMC consists of 4 modules: (1) AHB interface (including FSMC configuration register) (2) NOR flash memory and PSRAM controller (when driving LCD, LCD is like a PSRA...[Details]
As many companies listed with
the concept of
touch screen
begin to "transform and upgrade", the official voice of the TP industry is getting smaller and smaller. At the same time, the list o...[Details]
There has been a lot of news about Huawei
phones
recently
. At the
Huawei
Global Analyst Conference
on the 17th
,
Huawei
announced that it will launch
5G
phones
in the seco...[Details]
Why does MCU have a watchdog? With this question, let's learn about watchdogs. Even the 51 single-chip microcomputer has a watchdog, which shows that this dog has a special meaning to us. The purpose...[Details]
T1 or T2 are two timers/counters of MCS-51 microcontroller. The first method can use two timers/counters to generate rectangular waves. In order to save interface resources, the second method is used...[Details]
For complex calculations, the speed of the microcontroller is too slow. The best way is to manually calculate all the results in advance, store them in ROM in sequence, and then directly check the re...[Details]
The circuit shown in the figure requires that the light is off when the machine is turned on. Press the button once, and the light D1 will turn on and automatically turn off after a delay of 10 secon...[Details]
//Environment: winavr+avr studio char temp=0; ISR(TIMER1_COMPA_vect )//interrupt function { // user code here temp++; if (temp==10) temp=0; PORTA=temp; DDRA=0xff; } void ...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
