5.0 mm x 3.2 mm Package Pinout ............................................................................................................................................... 1
Ordering Information .................................................................................................................................................................... 2
Device Configurations and Pin-outs ............................................................................................................................................. 9
Pin-out Top Views................................................................................................................................................................. 9
Test Circuit Diagrams for LVCMOS and Clipped Sinewave Outputs ......................................................................................... 10
Frequency Stability ............................................................................................................................................................. 16
Output Frequency and Format............................................................................................................................................ 16
Output Frequency Tuning ................................................................................................................................................... 16
Pin 1 Configuration (OE, VC, or NC) .................................................................................................................................. 17
Control Voltage Bandwidth ................................................................................................................................................. 20
Pull Range and Average Pull Range .................................................................................................................................. 22
Output Frequency ............................................................................................................................................................... 23
2
I C Control Registers .......................................................................................................................................................... 25
Serial Interface Configuration Description .......................................................................................................................... 28
Serial Signal Format ........................................................................................................................................................... 28
Parallel Signal Format ........................................................................................................................................................ 29
Parallel Data Format ........................................................................................................................................................... 29
2
I C Timing Specification ...................................................................................................................................................... 31
2
I C Device Address Modes ................................................................................................................................................. 32
Schematic Example ............................................................................................................................................................ 33
Dimensions and Patterns ........................................................................................................................................................... 34
Additional Information ................................................................................................................................................................ 36
Revision History ......................................................................................................................................................................... 37
Rev 1.05
Page 3 of 38
www.sitime.com
SiT5156
1 MHz to 60 MHz, ±0.5 to ±2.5 ppm, Elite Platform™ Super-TCXO
Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise
stated. Typical values are at 25°C and 3.3V Vdd.
Table 1. Output Characteristics
Parameters
Nominal Output Frequency Range
Operating Temperature Range
Symbol
F_nom
T_use
Min.
1
-20
-40
-40
Frequency Stability over
Temperature
Initial Tolerance
Supply Voltage Sensitivity
F_stab
–
–
–
F_init
F_Vdd
–
–
–
–
Output Load Sensitivity
F_load
–
–
–
Frequency vs. Temperature Slope
ΔF/ΔT
–
–
–
Dynamic Frequency Change during
Temperature Ramp
One-Year Aging
20-Year Aging
F_dynamic
–
–
–
F_1y
F_20y
–
–
Typ.
–
–
–
–
–
–
–
–
±7.10
±11.83
±28.40
±0.81
±1.35
±3.24
±15
±25
±60
±0.13
±0.21
±0.50
±1
±2
Max.
60
+70
+85
+105
±0.5
±1.0
±2.5
±1
±16.25
±32.50
±65.0
±2.75
±5.50
±11.00
±25
±50
±100
±0.21
±0.42
±0.83
–
–
Unit
MHz
°C
°C
°C
ppm
ppm
ppm
ppm
ppb
ppb
ppb
ppb
ppb
ppb
ppb/°C
ppb/°C
ppb/°C
ppb/s
ppb/s
ppb/s
ppm
ppm
Initial frequency at 25°C at 48 hours after 2 reflows
I think everyone agrees that in embedded development, theory and practice complement each other. The study of Ethernet is no exception. It is necessary to master the necessary theoretical knowledge, o...
[b]How to determine the value of the feedback resistor of the op amp[/b] [b]For example, if the gain factor is 10, 1k:10k or 10k:100k are both acceptable. Is there any way to calculate it?[/b]...
The CLA of C2000 does not support breakpoint debugging, so you can only add MDEBUGSTOP to the program to pause CLA. There are a few points to note when using MDEBUGSTOP: 1. When CLA is not connected, ...
[i=s]This post was last edited by le062 on 2015-3-19 00:21[/i] [align=left][font=Lato, sans-serif][size=3][color=#2b2b2b]In a single-chip microcomputer, the CPU is usually awakened by an interrupt eve...
I have read a lot of information on the Internet, but they are all made of capacitors, op amps and diodes. The fastest speed of the board I made with these can only reach 1MHz. I wonder if anyone know...
The core of a machine vision system is image acquisition and processing. All information comes from images, and image quality is crucial to the entire vision system. A good image can improve the st...[Details]
Tesla and BYD, vying for dominance in the global electric vehicle market, are reportedly considering adopting Samsung's AMOLED (active-matrix organic light-emitting diode) technology for their next...[Details]
How do you know if a machine is operating properly? The answer: by leveraging deep learning to detect anomalies in routine vibration data from industrial machines. Anomaly detection has many uses, ...[Details]
The problem of dynamic sealing of equipment always exists with the operation of the equipment. Today, we have specially sorted out the various commonly used sealing forms, usage scope and character...[Details]
introduction
With the development of digital and network technologies, broadcasting technology has become increasingly diversified, with the most significant trend being the transition from an...[Details]
As more and more consumers purchase new energy vehicles, the safety of electric vehicles has become a major concern. This has been particularly prominent following a series of electric vehicle fire...[Details]
When we travel in cities, we all find that electric vehicles have many advantages. As a means of transportation, they can also fulfill their mission well. Now, more and more residential communities...[Details]
Is pure electric vehicles a false proposition for long-distance driving? At least from my personal perspective, based on current technological and infrastructure standards, I believe so. Below, I'l...[Details]
Topics: Bring Your Own Device (BYOD) trends; the impact of using employees' own mobile devices to control access to work facilities and equipment on information security; and ways to securely imple...[Details]
On August 22nd, Lantu Motors unveiled a new technology called "Lanhai Intelligent Hybrid" during a live broadcast of CCTV News' "Top Laboratory." The name sounds like another new term, but a closer...[Details]
Keysight Technologies is combining its electromagnetic simulator with Synopsys' AI-driven RF design migration flow to create an integrated design flow for migrating from TSMC's N6RF+ process techno...[Details]
SMT placement machines are important equipment in surface mount technology (Surface Mount Technology). Their performance has a decisive impact on the quality and efficiency of electronic manufactur...[Details]
Plessey Semiconductors has been acquired by Haylo Labs, which was established in March last year with a $100 million, five-year loan from Chinese technology company Goertek.
Haylo Labs w...[Details]
Reflow soldering, as an electronics assembly process, has become a vital component of the electronics manufacturing industry. Choosing reflow soldering equipment is crucial for improving production...[Details]
With the support and encouragement of national policies, some Internet car manufacturers have also joined the new energy vehicle manufacturing industry. From the perspective of new car manufacturer...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
