Features ....................................................................................................................................................................................... 1
Ordering Information .................................................................................................................................................................... 2
LVPECL and FlexSwing Termination .................................................................................................................................. 17
LVDS, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 18
HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 18
Low-power HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V.................... 18
Dimensions and Patterns ― 2.0 x 1.6 mm x mm ....................................................................................................................... 19
Dimensions and Patterns ― 2.5 x 2.0 mm x mm ....................................................................................................................... 20
Dimensions and Patterns ― 3.2 x 2.0 mm x mm ....................................................................................................................... 21
Revision History ......................................................................................................................................................................... 22
Rev 0.52
Page 3 of 23
www.sitime.com
SiT9375
Low Jitter Differential XO for Standard Frequencies
Electrical Characteristics
ADVANCED
All Min and Max limits in the Electrical Characteristics tables are specified over operating temperature and rated operating
voltage with standard output termination shown in the termination diagrams. Typical values are at 25°C and nominal
supply voltage.
Table 3. Electrical Characteristics – Common to All Output Signaling Types
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
–
Min.
Typ.
Max.
Unit
MHz
ppm
Condition
Refer to frequencies listed in
Ordering Information
section.
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and 10 years
aging at 25°C
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and first year aging
at 25°C
Ambient temperature of 25°C
Extended commercial, ambient temperature
Industrial, ambient temperature
Ambient temperature
Extended industrial, ambient temperature
Voltage-supply order code “YY”
Voltage-supply order code “XX”
Voltage-supply order code “18”.
Contact SiTime
for 1.5 V
Voltage-supply order code “25”
Voltage-supply order code “33”
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
See
Figure 5
and
Figure 7
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin toggles to enable logic level to
the time clock pins reach 90% of swing. See
Figure 12
Measured from the time OE pin toggles to disable logic level to
the last clock edge. See
Figure 13
12 kHz to 20 MHz offset frequency integration bandwidth,
156.25 MHz
12 kHz to 20 MHz offset frequency range, 156.25 MHz
12 kHz to 20 MHz offset frequency range, 155.52 MHz
156.25 MHz
156.25 MHz
Frequency Range
Standard frequencies
–
±20
Frequency Stability
–
–
–
10 Year Aging
Operating Temperature Range
F_10y
T_use
–
-20
-40
-40
-40
Supply Voltage
Vdd
1.71
2.25
1.71
2.25
2.97
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Startup Time
Output Enable Time
Output Disable Time
VIH
VIL
Z_in
DC
T_start
T_oe
T_od
70%
–
–
45
–
–
–
–
–
–
±1
–
–
–
–
–
–
1.80
2.50
3.30
–
–
100
–
1
–
–
±25
±30
±50
–
+70
+85
+95
+105
ppm
ppm
ppm
ppm
°C
°C
°C
°C
V
V
V
V
V
Temperature Range
Supply Voltage
3.63
3.63
1.89
2.75
3.63
Input Characteristics
–
Vdd
30%
–
55
5
100+3 clock
cycles
100+3 clock
cycles
Vdd
kΩ
%
ms
ns
ns
Output Characteristics
Startup, OE and SE Timing
Jitter and Phase Noise
RMS Phase Jitter (random)
Spurious Phase Noise
RMS Period
Jitter
[1]
Jitter
[1]
T_phj
PN_spur_a
PN_spur_b
T_jitt_per
T_jitt_cc
Peak Cycle-to-cycle
–
–
–
–
–
200
-110
-80
1
6
–
–
–
–
–
fs
dBc
dBc
ps
ps
Note:
1. Measured according to JESD65B.
Rev 0.52
Page 4 of 23
www.sitime.com
SiT9375
Low Jitter Differential XO for Standard Frequencies
ADVANCED
Table 4. Electrical Characteristics – LVPECL
|
Supply voltages: 2.5 V
±10%,
3.3 V
±10%,
2.25 V to 3.63 V
Parameter
Current Consumption, Output
Enabled without Termination
Current Consumption, Output
Enabled with Termination 1
Current Consumption, Output
Enabled with Termination 2
Current Consumption, Output
Disabled without Termination
Current Consumption Output
Disabled with Termination 1
Current Consumption, Output
Disabled with Termination 2
OE Leakage Current
Symbol
Idd_oe_nt
Idd_oe_wt1
Idd_oe_wt2
Idd_od_nt
Idd_od_wt1
Idd_od_wt2
I_leak
Min.
–
–
–
–
–
–
–
Typ.
43
52
71
58
58
86
37
Max.
–
–
–
–
–
–
–
Unit
mA
mA
mA
mA
mA
mA
mA
Condition
Excluding load termination current
Including load termination current. See
Figure 15
for
termination
Including load termination current. See
Figure 18
for
termination
Excluding load termination current
Including load termination current. See
Figure 15
for
termination
Including load termination current. See
Figure 18
for
termination
OE = disable logic, DC termination, OUTP and OUTN held
From EEWORLD cooperation group: 499581 Group owner: wangkj The yellow one is connected to the ground. The adjacent ones are pulled into a straight line. The farthest one has only one jump. The four li...
China's domestically produced C919 large passenger aircraft received a launch order for 100 aircraft On November 16, Commercial Aircraft Corporation of China, Ltd. and six Chinese and foreign companie...
Hello everyone, I use PDIUSBD12 to make a USB sound card. Now I want to configure endpoint 2 of PDIUSBD12 to synchronous transfer mode, but I haven't been able to do it. If you know how, please help m...
I downloaded the official website routine directly, and the cmd file is also for f28027. It compiles successfully, but every time I download it, it shows this regardless of whether the board is connec...
I'm looking for a project package for the voice recording and playback system based on the S3C44B0 development board. The debugging tool uses ADS1.2. If you have one, please send it to me! I'll be ver...
Today, when I was browsing the forum, I saw a post on the Stellaris section that was collecting difficult and complicated problems. Let's take a look at it for reference!
Any difficult problems you en...
The U.S. Food and Drug Administration (FDA) points out that home health care is the fastest growing area in the medical device industry. Driven by the increase in average life expectancy, the increasi...[Details]
Ultrasound systems are among the most sophisticated and complex signal processing instruments in widespread use today. Like any complex instrument, there are many trade-offs to be made in implement...[Details]
Controller Area Network (CAN) is a type of fieldbus. It is a serial communication network that effectively supports distributed control or real-time control and is recognized as one of the most pro...[Details]
This summary will introduce the transmitter characteristic test of TD terminal products - uplink power control. According to the 3GPP TS34.122 standard, UE uplink power control is divided into uplink ...[Details]
Overview
In recent years, the vigorous development of integrated circuits has created a huge space for the research and application of digital circuits. FPGA has low power consumption, high re...[Details]
Introduction
The MAX2116 P1db data is measured at specific combinations of RF and baseband gain over the adjustable range of these two gains. These data can be used to select gain control se...[Details]
According to In-Stat/MDR, the number of mobile phones with Bluetooth capabilities will reach at least 300 million by 2005. One of the clear evidences of the increasing adoption of Bluetooth is that...[Details]
In the process of RF transceiver application, adjusting the processing gain (PG) of the direct sequence spread spectrum communication system (DSSS) can obtain excellent anti-noise performance, whic...[Details]
Portable products are generally powered by batteries. Due to cost and size considerations, there is a trend to reduce the number and size of batteries used in design. If the number of batteries is ...[Details]
1 Introduction
In many communication systems, the base station usually sends a training sequence for the terminal to synchronize with the system. The synchronization here includes time syn...[Details]
The four-element infrared detector uses photosensitive elements, and the alarm is triggered only when each detector detects a signal. It has stronger anti-false alarm capability and better detectio...[Details]
Modern living patterns make the safety of family life particularly important. At present, security prevention and alarm systems are important guarantees for ensuring the safety of residences and re...[Details]
introduction
SPI (Serial Peripheral InteRFace) is a synchronous serial peripheral interface introduced by Motorola. Due to its advantages such as simple protocol implementation and fast tr...[Details]
0 Introduction
IIR filters are not easy to make into linear phase, but FIR filters can be made into linear phase as long as certain conditions are met. The requirement for linear phase is ...[Details]
In industrial and agricultural production, the transmission of collected data is mostly done by wired means, because the transmission distance, data transmission rate and anti-interference ability ...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
