EEWORLDEEWORLDEEWORLD

Part Number

Search

BZW04-14A1

Description
Trans Voltage Suppressor Diode, 400W, 13.6V V(RWM), Unidirectional, 1 Element, Silicon, DO-41,
CategoryDiscrete semiconductor    diode   
File Size257KB,6 Pages
ManufacturerTaiwan Semiconductor
Websitehttp://www.taiwansemi.com/
Environmental Compliance
Download Datasheet Parametric View All

BZW04-14A1 Overview

Trans Voltage Suppressor Diode, 400W, 13.6V V(RWM), Unidirectional, 1 Element, Silicon, DO-41,

BZW04-14A1 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerTaiwan Semiconductor
package instructionO-PALF-W2
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresEXCELLENT CLAMPING CAPABILITY, LOW IMPEDANCE, PRSM-MIN
Maximum breakdown voltage16.8 V
Minimum breakdown voltage15.2 V
Shell connectionISOLATED
ConfigurationSINGLE
Diode component materialsSILICON
Diode typeTRANS VOLTAGE SUPPRESSOR DIODE
JEDEC-95 codeDO-41
JESD-30 codeO-PALF-W2
Maximum non-repetitive peak reverse power dissipation400 W
Number of components1
Number of terminals2
Maximum operating temperature175 °C
Minimum operating temperature-55 °C
Package body materialPLASTIC/EPOXY
Package shapeROUND
Package formLONG FORM
polarityUNIDIRECTIONAL
Maximum power dissipation1 W
Maximum repetitive peak reverse voltage13.6 V
surface mountNO
technologyAVALANCHE
Terminal formWIRE
Terminal locationAXIAL
creat by art
BZW04 SERIES
400 Watts Transient Voltage Suppressor
DO-41
Features
Plastic package has Underwriters
Laboratory Flammability Classification 94V-0
Exceeds environmental standards of MIL-STD-19500
400W surge capability at 10 x 1000 us waveform
Excellent clamping capability
Low impedance surge resistance
Very fast response time
Typical I
R
less than 1uA above 10V
High temperature soldering guaranteed:
260℃ / 10 seconds
Green compound with suffix "G" on packing
code & prefix "G" on datecode
Mechanical Data
Case: Molded plastic
Lead: Axial leads, solderable per MIL-STD-202,
Method 208
Polarity: Color band denotes cathode except bipolar
Weight: 0.34 gram
Ordering Information (example)
Part No.
BZW04-10
Package
DO-41
Packing
3K / AMMO box
INNER
TAPE
52mm
Packing code
A0
Packing code
(Green)
A0G
Maximum Ratings and Electrical Characteristics
Rating at 25
ambient temperature unless otherwise specified.
Parameter
Peak Pulse Power Dissipation at T
A
=25℃,
Tp=1ms(Note 1)
Steady State Power Dissipation at T
L
=75℃
Lead Lengths .375", 9.5mm (Note 2)
Peak Forward Surge Current, 8.3ms Single Half
Sine-wave Superimposed on Rated Load
(JEDEC method)(Note 3)
Junction to leads
Junction to ambient on printed circuit
L lead=10mm
Operating and Storage Temperature Range
Note 2: Mounted on copper pad area of 0.2" x 0.2" (5 x 5mm)
Symbol
P
PK
P
D
Value
Minimum 400
1
Unit
Watts
Watts
I
FSM
R
θJL
R
θJA
T
J
, T
STG
40
60
100
-55 to +175
Amps
℃/W
℃/W
Note 1: Non-repetitive Current Pulse, Per derated above TA=25℃
Note 3: Measure on 8.3ms single half sine-wave or equivalent square wave, duty cycle=4 pulses per minute maxumum.
Version:G13
Classification of power amplifiers
[size=4]Power amplifiers are usually divided into five categories according to their working status. That is, Class A (A), Class B (B), Class AB (AB), and Class D (D). [/size] [size=4] [/size] [size=4...
fish001 Analogue and Mixed Signal
I'm looking for some advice. I wrote a pulse generator using Verilog and a weird problem occurred. . .
I made a pulse generator with a pulse interval of 45.5ms and a pulse width of 1us. However, when tested with an oscilloscope, it always fluctuates between 45.4 and 45.6ms. But when I changed the inter...
qqichang FPGA/CPLD
《TMS320X281x DSP Principles and C Program Development》
[[i]This post was last edited by dontium on 2011-12-23 11:32[/i]]...
dontium Microcontroller MCU
About Jlink download AXD debugging problem
, I use mini2440, and the following problem occurs when configuring CodeWarrior. I can't solve it. Can an expert take a look: After I successfully connect with JLINK, why does the value of R0 register...
Learner_new ARM Technology
If you want to know whether the signal generated by the signal generator or function generator is ready or whether it is input according to the set value standard...
If I want to know whether the signal generated by a signal generator or function generator is ready or output according to the set value standard, what instrument can be used to verify it? Please help...
QWE4562009 Integrated technical exchanges
Continuous Development
txj, the purpose of open source is to make a better rtos, and the purpose of closed source is to develop continuously. The two are not in conflict. The problem now is cash flow, marketing, or RAWOS-ba...
yexiaoxin1992 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 885  2814  898  1072  2661  18  57  19  22  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号