EEWORLDEEWORLDEEWORLD

Part Number

Search

PFC-W1206R-12-7411-A

Description
Fixed Resistor, Thin Film, 0.333W, 7410ohm, 200V, 0.05% +/-Tol, 10ppm/Cel, Surface Mount, 1206, CHIP
CategoryPassive components    The resistor   
File Size399KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

PFC-W1206R-12-7411-A Overview

Fixed Resistor, Thin Film, 0.333W, 7410ohm, 200V, 0.05% +/-Tol, 10ppm/Cel, Surface Mount, 1206, CHIP

PFC-W1206R-12-7411-A Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerTT Electronics plc
package instructionCHIP
Reach Compliance Codecompli
Other featuresHIGH PRECISION
structureRECTANGULAR PACKAGE
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.61 mm
Package length3.2 mm
Package formSMT
Package width1.6 mm
method of packingTR, EMBOSSED PLASTIC, 7 INCH
Rated power dissipation(P)0.333 W
Rated temperature70 °C
resistance7410 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient10 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb)
Terminal shapeWRAPAROUND
Tolerance0.05%
Operating Voltage200 V
Precision Thin Film
Chip Resistors
PFC Series
Standard 60/40 Sn/Pb and Pb-free (RoHS compliant) terminations available
Available in 0402, 0603, 0805, 1206, 1505, 2010 and 2512 chip sizes
Tested for COTS applications
Absolute TCR to ±10ppm/°C
MIL screening available
IRC Advanced Film Division
Ultra stable Tantalum Nitride
resistor film system
Non-leaching
Nickel barrier
Wrap around
termination
The IRC TaNFilm
®
PFC chip resistor series provides the high precision and ultra stable performance of our
Tantalum Nitride resistive film system in 0402, 0603, 0805, 1206, 1505, 2010 and 2512 sizes. The unique
characteristics of the passivated Tantalum Nitride film insure long term life stability and stability in most envi-
ronments.
Using the same manufacturing line as the PFC Military Series, IRC’s precision chips maintain the same supe-
rior environmental performance. Specially selected materials and processes insure initial precision is main-
tained in the harshest surface mount soldering environment. Wrap-around terminations with leach-resistant
nickel barriers insure high integrity solder connections.
Electrical Data
Model
Power Rating
(70°C)
50mW
100mW
250mW
333mW
350mW
800mW
1.0W
Max Voltage
Rating (≤
P x R)
75V
75V
100V
200V
100V
175V
200V
-55°C to +150°C
2KV to 4KV
(HBM)
<-25dB
Temperature
Range
ESD
Sensitivity
Noise
Termination
Substrate
W0402
W0603
W0805
W1206
W1505
W2010
W2512
60/40 Sn/Pb
or 100% tin
(RoHS
compliant)
plated over
nickel barrier
99.5%
Alumina
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
PFC Series Issue May 2008 Sheet 1 of 4
wince6 Eboot boot!!!
Eboot加载失败,DNW输出如下信息:WinCE NAND Boot v1.00 Aug 05 2008 15:04:47 Load EBOOT ...... ECC mismatch for Sector: 0x00000120 ERR_DISK_OP_FAIL2: 0x00000120 ECC mismatch for Sector: 0x00000121 ERR_DISK_OP_FAIL2...
jk_3333 Embedded System
The LM5118 buck-boost circuit has poor load capacity?
The following figure shows a buck-boost circuit generated using TI WEBENCH. The main control IC is LM5118.The parameters are as followsInput voltage range: DC22.0V-DC45V;Output voltage: DC24.0V;Contin...
yhyworld Power technology
Optimization Design of AC Side Filter Inductor of Parallel Active Power Filter
Abstract: This paper discusses a method for optimizing the design of filter inductance on the AC side of a shunt active power filter. It is applied to an experimental model of a 15kVA shunt active pow...
zbz0529 PCB Design
Common fault causes and solutions for CCD cameras
1. No video signal output after power-on. First check whether the polarity of the external power supply is correct and whether the voltage meets the requirements. 2. Color distortion may be caused by ...
xyh_521 Industrial Control Electronics
I'll apply
:) , I don’t know what conditions I need to meet to apply~...
longye199035 NXP MCU
When porting busybox, only three files are automatically generated after install, and there is no usr file
I followed the method of porting busybox1.9.2 on the Internet, modified the compiler path in Makefile, and executed make menuconfig for configuration. I basically used the default configuration, dynam...
kfchu Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1528  2240  1950  252  2765  31  46  40  6  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号