302075-9TP856K00DB datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> 302075-9TP856K00DB

302075-9TP856K00DB: DescriptionFixed Resistor, Metal Foil, 2.25W, 856000ohm, 600V, 0.5% +/-Tol, -2,2ppm/Cel,; CategoryPassive components The resistor; File Size451KB，6 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

302075-9TP856K00DB Overview

Fixed Resistor, Metal Foil, 2.25W, 856000ohm, 600V, 0.5% +/-Tol, -2,2ppm/Cel,

302075-9TP856K00DB Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Vishay
Reach Compliance Code	unknow
structure	Hermetically Sealed
JESD-609 code	e3
Lead diameter	0.64 mm
Lead length	25.4 mm
Number of terminals	4
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package diameter	12.7 mm
Package length	38.1 mm
Package form	4 Terminals
method of packing	Bulk
Rated power dissipation(P)	2.25 W
resistance	856000 Ω
Resistor type	FIXED RESISTOR
series	H SERIES-OTHER
technology	METAL FOIL
Temperature Coefficient	-2,2 ppm/°C
Terminal surface	Tin (Sn)
Tolerance	0.5%
Operating Voltage	600 V

Preview

Download Datasheet

View All

H Series

Vishay Foil Resistors

New Generation of Secondary Standards Hermetically Sealed High Precision Bulk

Metal

Foil Technology Resistors with TCR of ± 2 ppm/°C, Tolerance of ± 0.001 % and

Load Life Stability of ± 0.005 % (Metrology, Laboratory, Instrumentation, Industrial)

FEATURES

•

Temperature coefficient of resistance (TCR):

± 2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C

ref.).

For

ultra

high

performances

(instrumentation and metrology) please refer to

the last page

•

Resistance range: 5

to 1.84 MΩ (higher or

lower values of resistance available)

•

Vishay Foil resistors are not restricted to standard values;

specific “as required” values can be supplied at no extra

cost or delivery (e.g. 1K2345 vs. 1K)

•

Power rating: 0.3 W to 2.5 W at + 25 °C (depending on

model - see table 2)

•

Tolerance: to ± 0.001 % (10 ppm)

•

Load life stability to ± 0.002 % (20 ppm) at 25 °C, 2000 h

at rated power

•

Load life stability can be considerably improved

through in-house stabilization

•

Shelf life stability: ± 2 ppm for at least 6 years

(unaffected by humidity)

•

Electrostatic discharge (ESD) up to 25 000 V

•

Rise time: 1 ns effectively no ringing

•

Thermal stabilization time < 1 s (nominal value achieved

within 10 ppm of steady state value)

•

Current noise: 0.010 µV

RMS

/V of applied voltage (< - 40 dB)

•

Thermal EMF: 0.05 µV/°C typical

•

Voltage coefficient: < 0.1 ppm/V

•

Non-inductive: < 0.08 µH

•

Non-inductive, non-capacitive design

•

Non hot spot design

•

Terminal finish available: lead (Pb)-free or tin/lead alloy

•

Impervious to harmful environments - oil-filled

•

Compliant to RoHS directive 2002/95/EC

•

Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vishaypg.com

•

For better performances (values, TCR, tolerance, stability),

please see the HZ series

INTRODUCTION

The H series resistors are oil-filled, hermetically sealed ultra

precision resistors and are used as secondary standards for

metrology applications.

The hermetic sealing eliminates the ingress of moisture and

oxygen, while the oil acts as a thermal conductor, thus

eliminating the long-term degradation elements of unsealed

resistors, while at the same time allowing the device to

accept short periods of overload without degradation.

Vishay’s Bulk Metal

Foil outperforms all other resistor

technologies available today for applications that require

precision and stability. When combined with the hermetic

sealing and oil filling, the H series resistors become

the most

precise and stable resistors available.

With accuracies of 0.001 %, a resistance range from 5

to 1.84 MΩ, and long term shelf life of less than 2 ppm,

these devices are virtually secondary standards that can be

carried in sets for daily or periodic calibration of factory

measurement equipment.

The H series is available with laboratory and metrology

level precision and long-term stability with additional

in-house oriented processes such as: chip stabilization,

special TCR plotting, additional treatments for ultra

stability and special post manufacturing operations

(PMO). (Please refer to the last page)

TABLE 1 - TCR VS. RESISTANCE VALUE

RESISTANCE

VALUE (Ω)

100 to < 1M84

50 to < 100

5 to < 50

TYPICAL TCR AND MAX. SPREAD

(- 55 °C to + 125 °C, + 25 °C ref.)

(ppm/°C)

± 2 ± 2.5

± 2 ± 3.5

± 2 ± 4.5

FIGURE 1 - SHELF LIFE - VHA518-11

12K9 VS. QHE

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

- 0.1

100 200 300 400 500 600 700 800 900 1000

Note

• For maximum TCR < 1 ppm/°C, see VHP100 and contact

application engineering

* Pb containing terminations are not RoHS compliant, exemptions may apply

Resistance Change (ppm)

Time (Days)

Document Number: 63006

Revision: 23-Mar-10

For any questions, contact:

foil@vishaypg.com

www.foilresistors.com

Recommended Resources

Classic car battery charging circuit diagram

Current detection circuit in inverter air conditioner

LS7261-LS7262 three-phase half-wave circuit

Battery charger circuit diagram using LT1513

Addition circuit

Computer motherboard circuit diagram 440LX2_05

Power Management Solutions for Multimedia Mobile Phones: I saw a good article about IC design, which gave some new ideas to students studying electronics.Multimedia applications such as mobile TV, mobile gaming, and audio playback present a huge challenge t...; soff Power technology

SUNPLUS launches 8-bit industrial-grade MCU learning board: Sunplus Technology (SUNPLUS) recently announced: Sunplus Technology (sunplus) launched the 8-bit industrial-grade MCU series - SPMC65 series learning board. The SPMC65 series MCU is an industrial-grad...; rain MCU

MSP430 UART bit error problem: Now I use the UART (full duplex, baud rate 9600) of MSP430F437, and found that there is a bit error phenomenon. For example, when the program sends "AA", the actual monitored data is "AC".The relevant...; cai5143 Microcontroller MCU

Questions about offset voltage and offset current: I have read several books for a long time but I still can't understand. Do they have the same principle for generating output voltage? Can any brother recommend some good books and some graphic materi...; yelingfeng Analog electronics

22 classic written test questions and answers for power supply engineers?: [p=null, 2, left][color=rgb(62, 62, 62)][b][b]1[/b][/b]Which of the following performance characteristics does the power save mode have?[/color][/p][p=null, 2, left][color=rgb(62, 62, 62)]A High light...; 木犯001号 Energy Infrastructure?

Is this warning in QuartusII serious? How should I deal with it?: Warning: Macrocell buffer inserted after node "RW". After compiling, there is only this warning. I don't know whether the consequences are serious. Please give me some advice, thank you!...; eeleader-mcu FPGA/CPLD

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components