EEWORLDEEWORLDEEWORLD

Part Number

Search

5KP17-E3/74

Description
Trans Voltage Suppressor Diode, 5000W, 17V V(RWM), Unidirectional, 1 Element, Silicon, PLASTIC, CASE P600, 2 PIN
CategoryDiscrete semiconductor    diode   
File Size108KB,6 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

5KP17-E3/74 Overview

Trans Voltage Suppressor Diode, 5000W, 17V V(RWM), Unidirectional, 1 Element, Silicon, PLASTIC, CASE P600, 2 PIN

5KP17-E3/74 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerVishay
package instructionO-PALF-W2
Contacts2
Manufacturer packaging codeCASE P600
Reach Compliance Codeunknow
ECCN codeEAR99
Maximum breakdown voltage23.1 V
Minimum breakdown voltage18.9 V
Shell connectionISOLATED
ConfigurationSINGLE
Diode component materialsSILICON
Diode typeTRANS VOLTAGE SUPPRESSOR DIODE
JESD-30 codeO-PALF-W2
JESD-609 codee3
Maximum non-repetitive peak reverse power dissipation5000 W
Number of components1
Number of terminals2
Maximum operating temperature175 °C
Minimum operating temperature-55 °C
Package body materialPLASTIC/EPOXY
Package shapeROUND
Package formLONG FORM
Peak Reflow Temperature (Celsius)NOT SPECIFIED
polarityUNIDIRECTIONAL
Maximum power dissipation8 W
Certification statusNot Qualified
Maximum repetitive peak reverse voltage17 V
surface mountNO
technologyAVALANCHE
Terminal surfaceMATTE TIN
Terminal formWIRE
Terminal locationAXIAL
Maximum time at peak reflow temperatureNOT APPLICABLE
5KP5.0 thru 5KP188A
Vishay Semiconductors
formerly General Semiconductor
T
RANS
Z
ORB
®
Transient Voltage Suppressors
Stand-off Voltage
5.0 to 188 V
Peak Pulse Power
5000 W
Features
• Glass passivated junction
• 5000 W peak pulse power capability with a
10/1000
µs
waveform, repetition rate (duty cycle):
0.05 %
• Excellent clamping capability
• Low incremental surge resistance
• Very fast response time
• Devices with V
(BR)
> 10 V I
D
are typically less than
1.0
µA
• Available in uni-directional polarity only
• Meets MSL level 1 per J-STD-020C
• AEC-Q101 qualified
Mechanical Data
Case:
Molded plastic body over glass passivated
junction. Epoxy meets UL 94V-0 Flammability rating
Terminals:
Solder plated or matte tin plated
(E3 Suffix) leads, Solderable per J-STD-002B and
Mil-STD-750, Method 2026
High temperature soldering guaranteed:
265 °C/10 seconds, 0.375" (9.5 mm) lead length,
5 lbs. (2.3 kg) tension
Polarity:
The color band denotes the cathode, which
is positive with respect to the anode under normal
TVS operation
Maximum Ratings and Characteristics
Ratings 25 °C, unless otherwise specified
Parameter
Peak pulse power dissipation
Peak pulse current
Steady state power dissipation
Peak forward surge current
Instantaneous forward voltage
Operating junction and storage
temperature range
Notes:
(1) Non-repetitive current pulse, per Fig. 3 and derated above T
A
= 25 °C per Fig. 2.
(2) Mounted on copper pad area of 1.6 x 1.6" (40 x 40 mm) per Fig. 5.
(3) Measured on 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum
Test condition
10/1000
µs
waveform
(1)
10/1000
µs
waveform
(1)
lead lengths 0.375“ (9.5 mm),
T
L
= 75 °C
100 A
(3)
(2)
Symbol
P
PPM
I
PPM
P
M(AV)
I
FSM
V
F
T
J
, T
STG
Value
5000
See next table
8.0
600
3.5
-55 to +175
Unit
W
A
W
A
V
°C
8.3 ms single half sine-wave
(3)
Document Number 88308
Rev. 1.2, 27-Oct-04
www.vishay.com
1
A mistake about Weifu
ORG 0000H SJMP MAIN MAIN:MOV P1,#FFH .5 ACALL DE05 CLR P1.5 CPL P3.0 REL1:JB P1.2,REL2 SETB P1.6 ACALL DE05 CLR P1.6 CPL P3.0 REL2:JB P1.3,REL3 SETB P1.7 ACALL DE05 CLR P1.7 CPL P3.0 REL3:MOV A,P1 ORL...
microchenhard Embedded System
The built-in sweep generation capability of the Series 2600A SourceMeter instrument enables faster throughput and precise timing control
The setup run time is to configure the SMU source and measure [1] parameters before performing the sweep . Therefore, the setup interval only needs to be run once. From there, the sweep can be run as ...
Jack_ma Test/Measurement
Agilent E3632A Repair
When the power is on and the load is not applied, I adjusted the voltage knob. When it reached 8V, I found that there was a burning smell and the area marked CR37 was black. Can someone tell me what i...
寒夜星辰 Power technology
Question + Why won't the program reset when it's running?
When the program does not enter LPM3 mode, when monitoring through the serial port.....
accboy TI Technology Forum
The core board cannot start UBOOT from NOR
The core board I just bought cannot boot from NOR. UBOOT has been burned in NOR. It can be normally booted from NOR on the development board. My board and the development board have the same reset cir...
zeng2730 Embedded System
Help
The TMS320F28335 timer does not use this statement (CpuTimer1, 150, 100000). What does 100000 mean?...
同一种调调 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1120  1204  2866  127  300  23  25  58  3  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号