313LBPPCZLJGB datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > 313LBPPCZLJGB

Preview

313LBPPCZLJGB: DescriptionSUBMERSIBLE LEVEL TRANSMITTER; File Size90KB，2 Pages; ManufacturerETC2

Download Datasheet View All

313LBPPCZLJGB Overview

SUBMERSIBLE LEVEL TRANSMITTER

Preview

Download Datasheet

View All

SUBMERSIBLE LEVEL TRANSMITTER

Model 313L

GENERAL PURPOSE

FEATURES:

•

All-welded, stainless steel construction

Rugged, all encapsulated electronics.

Leakproof

1/2” NPT conduit thread standard

Standard

PRESSURE RANGES:

• From 0-3 through 0-100 psig

(See ordering guide.)

ACCURACY:

• From

±0.1%

FSO (RSS) to

±0.5%

FSO (RSS)

(See specifications & ordering guide.)

with Option LJ

tapered inlet with

stand off plate

ORDERING GUIDE

Ordering: Specify model, and pressure range and indicate modifications or

accessories required.

Use the following codes to identify desired item. Example 313L-B-PZ-LJ

MODEL

SERIES

RANGE

OPTIONS

•

MODEL

313L 4-20mA

SERIES

±0.5%

FSO (RSS)

±0.2%

FSO (RSS)

±0.1%

FSO (RSS)

•

•/•/•

OPTIONS

None (standard connector)

Alternate cable length (specify)

ALTERNATE PRESSURE PORT

1/8” NPT (F)

1/8” NPT (M)

Tapered inlet

Tapered inlet with standoff plate

PRESSURE RANGE

psi

in wc

100

150

7.5

200

300

100

GENERAL

Tefzel jacketed cable

Standardized output to

±0.5%

FSO

Alternate output, pressure units, or full scale

outputs that are non-standard

Improved temperature compensation to

±0.5%

FSO

unless otherwise specified

Alternate calibration signal

Internal calibration resistor set to 100

±0.5%

FSO

unless other wise specified

Remote cable mounted (in-line) zero & span controls. 3’ cable on open

side. Length of cable on closed side as required. (500’ maximum)

Customer special

Specifications printed on reverse side of this brochure.

GP:50 reserves the right to make product improvements and amendments to the product specification stated throughout this

brochure without prior notification. Please contact the factory on all critical dimensions and specifications for verification.

TOPE Co., Ltd.

Tel. (02) 8228-0658 • Fax. (02) 8228-0659 • E-mail: tope@ms1.hinet.net • Website: www.sensor.com.tw

SL5B-313L.02C

Recommended Resources

Intelligent lighting system indoor light collection circuit diagram

DC/DC power supply circuit diagram controlled by NCP1562

Circuit that uses indicator light to detect frequency

Dual high and low power linear regulator circuit diagram

Negative voltage to positive voltage conversion circuit diagram 1

100kHz oscillator circuit

#eeworld comic masterpiece#TI MCU comic, electronic cockroach & TI MCU access control system!: The system is easy to use, but it is hard to defend against it.More details: https://www.eeworld.com.cn/comic/comic_view.php?imgid=10...; EEWORLD社区 Microcontroller MCU

Measures to reduce interference in digital model design process: In the process of digital-analog design, we should avoid copying experience and rules. However, to thoroughly explain this problem, we must first understand the mechanism of digital-analog interferenc...; qwqwqw2088 Analogue and Mixed Signal

"Vds-id" gate voltage step by step: The default settings for running the Vds-id DC ITM drain [1] sweep voltage are 0-4Vin100 mVsteps, andthe gate voltage has three levels:1.5,2.0,2.5V(Figure1, Figure2). When changing these settings, ple...; Jack_ma Test/Measurement

The award-winning live broadcast will start at 10:00 this morning: "Dadatong helps you unlock the new generation of ADAS technology": The award-winning live broadcast will start at 10:00 this morning: "Dadatong helps you unlock the new generation of ADAS technology"Click here to enter the live broadcastLive broadcast time: 10:00-11:...; EEWORLD社区 Automotive Electronics

As an antenna engineer, I don't agree with superstition (reposted): I started working with antennas in early 2006. I occasionally made antennas for my tutors at school, but my main job was not in this area. After graduation, I went to a communications equipment compan...; john_wang RF/Wirelessly

Mouse filter driver problem: Using the moufiltr example in DDK, add a few lines of code in MouFilter_ServiceCallback: PMOUSE_INPUT_DATA pCursor; for (pCursor=InputDataStart;pCursorLastX,pCursor-LastY); } But I can't see the print...; mq13947193109 Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components