EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB
FE PACKAGE
16-LEAD PLASTIC TSSOP
T
JMAX
= 150°C,
θ
JA
= 40°C/W,
θ
JC(PAD)
= 10°C/W
ORDER INFORMATION
LEAD FREE FINISH
LT3518EUF#PBF
LT3518IUF#PBF
LT3518EFE#PBF
LT3518IFE#PBF
LT3518HFE#PBF
TAPE AND REEL
LT3518EUF#TRPBF
LT3518IUF#TRPBF
LT3518EFE#TRPBF
LT3518IFE#TRPBF
LT3518HFE#TRPBF
PART MARKING*
3518
3518
3518FE
3518FE
3518HFE
PACKAGE DESCRIPTION
16-Lead (4mm
×
4mm) Plastic QFN
16-Lead (4mm
×
4mm) Plastic QFN
16-Lead Plastic TSSOP
16-Lead Plastic TSSOP
16-Lead Plastic TSSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
3518fb
2
LT3518
ELECTRICAL CHARACTERISTICS
PARAMETER
Minimum V
IN
Operating Voltage
Maximum V
IN
Operating Voltage
Current Sense Voltage (V
ISP
– V
ISN
)
10% Scale Current Sense Voltage (V
ISP
– V
ISN
)
Current Sense Voltage Line Regulation
V
IN
Supply Current
Continuous Operation (Note 3)
V
CTRL
= 2V, V
ISP
= 24V, V
C
= 1V
V
CTRL
= 2V, V
ISP
= 0V, V
C
= 1V
V
CTRL
= 100mV, V
ISP
= 24V, V
C
= 1V
2V < V
ISP
< 45V
PWM > 1.5V, V
C
= 0V
PWM = 0V
SHDN
= 0V
R
T
= 16.7k
R
T
= 4.03k
R
T
= 91.5k
SS = 0.5V, Out of Pin
V
SYNC
= 2V
1.5
R
T
= 91.5k (250kHz)
SYNC = 300kHz Clock Signal, R
T
= 91.5k
R
T
= 16.7k (1MHz)
R
T
= 4.03k (2.5MHz)
I
SW
= 1.5A
V
SW
= 45V, PWM = 0V
Current Out of Pin, V
CTRL
= 0.1V
20
550
1000
PWM = 0, V
C
= 1V
Current Out of Pin, V
FB
= 0.5V
l
l
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. (Note 2) V
IN
= 5V,
SHDN
= 5V, PWM = 5V unless otherwise noted.
CONDITIONS
MIN
30
96
100
100
9
0.03
6
4.5
0.1
0.85
2.25
220
6
1.0
2.5
250
1
9
60
0.4
95
94
85
2.3
97
96
90
74
2.8
400
2
100
3.5
12
10
1
1.15
2.7
270
103
TYP
MAX
3
UNITS
V
V
mV
mV
mV
%/V
mA
mA
μA
MHz
MHz
kHz
V
μA
μA
V
V
%
%
%
%
A
mV
μA
nA
μS
kΩ
20
100
1.04
300
20
1.5
0.4
60
1.5
0.4
60
1.5
0.4
TGEN = 5V
I
REF
= –100μA
l
Switching Frequency
R
T
Voltage
Soft-Start Pin Current
SYNC Pull-Down Current (Into the Pin)
SYNC Input Low
SYNC Input High
Maximum Duty Cycle
l
Switch Current Limit
Switch V
CESAT
Switch Leakage Current
CTRL Input Bias Current
Error Amplifier Transconductance
V
C
Output Impedance
V
C
Idle Input Bias Current
FB Pin Input Bias Current
FB Pin Threshold
ISP , ISN Idle Input Bias Current
ISP , ISN Full-Scale Input Bias Current
SHDN
Voltage High
SHDN
Voltage Low
SHDN
Pin Bias Current
PWM Input High Voltage
PWM Input Low Voltage
PWM Pin Bias Current
TGEN Input High Voltage
TGEN Input Low Voltage
TGEN Pin Bias Current
V
REF
Pin Voltage
PWM = 0V
ISP Tied to ISN, V
ISP
= 24V, V
CTRL
= 2V
–20
0.98
0
20
1.01
nA
nA
V
nA
μA
V
V
μA
V
V
μA
V
V
μA
V
3518fb
100
120
100
1.96
2
200
2.04
3
LT3518
ELECTRICAL CHARACTERISTICS
PARAMETER
V
REF
Pin Voltage Line Regulation
Gate Turn-On Delay
Gate Turn-Off Delay
Top Gate Drive V
GS
(V
ISP
– V
TG
)
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. (Note 2) V
IN
= 5V,
SHDN
= 5V, PWM = 5V unless otherwise noted.
CONDITIONS
3V < V
IN
< 40V
C
LOAD
= 1nF Between ISP and TG
C
LOAD
= 1nF Between ISP and TG
V
ISP
= 24V, TGEN = 5V
PWM = 0V
200
200
7
0
0.3
MIN
TYP
MAX
0.03
UNITS
%/V
ns
ns
V
V
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LT3518E is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LT3518I is guaranteed over the full –40°C to 125°C operating junction
temperature range. The LT3518H is guaranteed over the full –40°C to
150°C operating junction temperature range. Operating lifetime is derated
at junction temperatures greater than 125°C.
Note 3:
Absolute maximum voltage at V
IN
,
SHDN,
PWM and TGEN pins
is 40V for nonrepetitive 1 second transients and 30V for continuous
operation.
Note 4:
This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed the maximum operating junction temperature
when overtemperature protection is active. Continuous operation above
the specified maximum operating junction temperature may impair device
The official capacitive touch button routine uses a watchdog timer and a TIMER A0 timer. When I add a TIMER A1 timer, I find that it interferes with the touch button and causes misjudgment of the touc...
1. Introduction to Siemens system data 810D and 840D system parameters are divided into two categories: machine data and setting data. Machine data is used for production, installation, and debugging ...
F-I56C Industrial ISA Interface MODEM Module Model: F-I56C-V1 Conexant Chip ISA Interface Caller ID MODEM F-I56C-V2 Conexant Chip ISA Interface Caller ID, Support Class 2 Protocol Fax MODEM Introducti...
The input range of a data acquisition system AD is 1.4Vp-p to 2.0Vp-p; a driver amplifier (for single-ended to differential conversion) is connected in front of the AD; a high-speed amplifier is conne...
[i=s] This post was last edited by Yunhu Congbai on 2022-2-10 10:40 [/i] ## Preface GD32L233 supports hardware random numbers, awesome +1. Let's first talk about the concept of random numbers. True ra...
Logic analyzers are widely used tools in digital design verification and debugging. They can verify the proper functioning of digital circuits and help users identify and troubleshoot faults. They ...[Details]
On August 22, Lantu Motors officially launched its Lanhai Intelligent Hybrid technology via an online livestream. This intelligent hybrid technology, which integrates a full-range 800V high-voltage...[Details]
Common Mode Semiconductor has officially released its latest generation of power management ICs—the GM6506 series. This fully integrated high-frequency synchronous rectification step-down p...[Details]
With the rapid development of electric vehicles in my country, people are beginning to pay attention to the issue of radiation from electric vehicles. We all know that mobile phones emit radiation,...[Details]
Electric vehicles are now widespread, but they've brought with them a host of problems, the most prominent of which is charging. Small electric vehicles (EVs) are a new form of transportation in a ...[Details]
In the field of intelligent driving, regulations are becoming increasingly stringent, and the technical threshold continues to rise. Especially after the traffic accident in March 2025, the Ministr...[Details]
The difference between a series inverter and a parallel inverter is that they use different oscillation circuits. A series inverter connects L, R, and C in series, while a parallel inverter connect...[Details]
In daily life, when we purchase a transformer, we are faced with the installation and wiring procedures. Generally speaking, large transformers such as power transformers are equipped with speciali...[Details]
Inverter power supplies on the market can generally be divided into two categories: sine wave inverters and square wave inverters. Some engineers also like to categorize pure sine wave inverters as...[Details]
introduction
In today's busy society, people experience chronic high stress, which in turn poses a significant threat to our health. Therefore, effectively relieving stress has become a pr...[Details]
In industrial production, many different controllers are often used, such as those for pressure, flow, electrical parameters, temperature, and sound. However, due to the limitations of the on-site ...[Details]
Automotive electronics systems are facing a dual challenge of functional safety and cybersecurity.
The NXP
S32K3
series MCUs utilize a deep protection system built with a Hardware Sec...[Details]
According to the latest financial report data, thanks to its leading position in advanced technology, TSMC's profit performance in the second quarter of 2025 was extremely impressive, with net prof...[Details]
With the improvement of China's supporting infrastructure and the accumulation of technology and capital, demand for industrial automation and intelligent applications of machine vision technology ...[Details]
While aberration theory is a vast subject, a basic understanding of some fundamental concepts can make it easier to understand: spherical aberration, astigmatism, field curvature, and chromatic abe...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
