380LQ561M200H022 datasheet, PDF

Datasheet> All Categories > Passive components> 380LQ561M200H022

380LQ561M200H022: DescriptionCAPACITOR, ALUMINUM ELECTROLYTIC, NON SOLID, POLARIZED, 200 V, 1000 uF, THROUGH HOLE MOUNT; CategoryPassive components; File Size408KB，6 Pages; ManufacturerETC2

Download Datasheet Parametric View All

380LQ561M200H022 Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	380LQ561M200H022	-	-	View	Buy Now

380LQ561M200H022 Overview

CAPACITOR, ALUMINUM ELECTROLYTIC, NON SOLID, POLARIZED, 200 V, 1000 uF, THROUGH HOLE MOUNT

380LQ561M200H022 Parametric

Parameter Name	Attribute value
Maximum operating temperature	85 Cel
Minimum operating temperature	-40 Cel
negative deviation	20 %
positive deviation	20 %
Rated DC voltage urdc	200 V
Processing package description	CAN, ROHS COMPLIANT
Lead-free	Yes
EU RoHS regulations	Yes
state	ACTIVE
terminal coating	Tin OVER Copper
Installation features	Through hole mounting
Manufacturer Series	380LQ
capacitance	1000 uF
packaging shape	Cylindrical PACKAGE
Capacitor type	non-solid
Terminal shape	SNAP-IN
equivalent series resistance	0.199ohm
polarity	polarization
ripple current	3.25A
leakage current	1341.65uA

Preview

Download Datasheet

View All

Type 380LQ

85 ºC Compact, High-Capacitance Snap-in

27% Smaller for Same Capacitance

Type 380LQ is on average 27% smaller and more than

10 mm shorter than Type 380LX. This is achieved with a

new can-closure method that permits installing capacitor

elements into smaller cans. Approaching the capability of

the 380LX, the new 380LQ enables you to shrink equipment

size and retain the original performance.

Highlights

• New, more capacitance per case

• Compare to Type 380LX

• New, lower voltages down to 16 V

Operating Temperature:

Rated Voltage:

Capacitance:

Leakage Current:

Ripple Current Multipliers:

–40 °C to + 85 °C

≤

315 Vdc

–25 °C to + 85 °C

≥

350 Vdc

16 to 450 Vdc

82 µF to 100,000 µF ± 20%

≤

√

CV µA, 4 mA max, 5 minutes

Ambient Temperature

45 ºC

1.50

Frequency

Freq. Hz

16 – 100 WV

160 – 450 WV

10 kHz

50 Hz 60 Hz 120 Hz 500 Hz 1 kHz & Up

0.93

0.75

0.95

0.80

1.00

1.05

1.20

1.08

1.25

1.15

1.40

60 ºC

1.46

70 ºC

1.30

85 ºC

1.00

Speciﬁcations

Complies with the EU Directive

2002/95/EC requirement

restricting the use of Lead (Pb),

Mercury (Hg), Cadmium (Cd),

Hexavalent chromium (Cr(VI)),

PolyBrominated Biphenyls

(PBB) and PolyBrominated

Diphenyl Ethers (PBDE).

Load LifeTest:

EIA Ripple Life:

Shelf Life:

2000 h at full load at 85 °C

∆

Capacitance ± 20%

ESR 200% of limit

DCL 100% of limit

2000 h at 85 °C, full load per EIA IS-749

∆

Capacitance –20%

ESR 200% of limit

DCL 100% of limit

1000 h at 85 °C

∆

Capacitance ± 20%

ESR 200% of limit

DCL 100% of limit

10 to 55 Hz, 0.06" and 10 g max, 2 h each plane

Vibration:

CDM Cornell Dubilier

•

140 Technology Place

•

Liberty, SC 29657

•

Phone: (864)843-2277

•

Fax: (864)843-3800

•

www.cde.com

Recommended Resources

The first 4Mbit EEPROM memory chip

LED lighting display detection circuit with overload protection

One of the reverse braking circuits for forward and reverse operation

TDA2009 power amplifier circuit diagram

Single junction transistor voltage dividing ratio measurement circuit

Under WinCE, develop a camera based on Microsoft's framework. How to connect it to the computer and use it as a camera?: The camera in WinCE is built successfully, not based on USB. Data collected by DShow can be displayed normally under WinCE. Now there is a new requirement that when our device is connected to a comput...; cumtlazyboy Embedded System

Question about FLASH_SetLatency();: Looking at the STM32 FLASH manual, the description of the LATENCY bit of the FLASH_ACR register clearly states:0 wait state if 0MHz1 wait state if 24MHz2 wait state if 48MHzMy SYSCLK is 72MHz, but I u...; bing stm32/stm8

A completely misunderstood device?: Reposted from other websitesWhy are instrumentation amplifiers so often misunderstood?The three-op-amp instrumentation amplifier shown in Figure 1 appears to be a simple structure because it uses the ...; ttianjiao Analog electronics

Investigate how people do GPRS data transmission. Use the protocol stack that comes with the GPRS module, or transplant a TCP/IP protocol stack?: Do a simple survey, use GPRS module as data transmission system, the method used by everyone is: 1. Use the protocol stack that comes with the GPRS module 2. Transplant a TCP/IP protocol stack, such a...; majuncheng Embedded System

TI CC2530 button controls the light on and off: CC2530 general purpose I/O interrupt After the general I/O pin is set as an input, it can generate an interrupt. The interrupt can be set to be triggered by the rising or falling edge of the external ...; Jacktang Wireless Connectivity

Could you please tell me what component this is?: Last night, my electric car charger exploded with a bang while charging. I took it apart and found a component marked F1 that exploded. I would like to ask you, what is this component? (There is a pic...; Ablikim Power technology

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components