EEWORLDEEWORLDEEWORLD

Part Number

Search

3GV64B-80M-155.25

Description
11.4 x 9.6 x 4.7mm 6 pad SMD
File Size346KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Download Datasheet View All

3GV64B-80M-155.25 Overview

11.4 x 9.6 x 4.7mm 6 pad SMD

EURO
QUARTZ
Frequency range 50.01MHz to 200MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
Low unit cost
GV64 CMOS VCXO
11.4 x 9.6 x 4.7mm 6 pad SMD
OUTLINE & DIMENSIONS
DESCRIPTION
GV64 VCXOs, are packaged in an industry-standard, 6 pad, 11.4mm
x 9.6mm x 4.7mm SMD package. The VCXO incorporates a high Q
fundamental mode crystal and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
Integrated Phase Jitter:
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
(Transfer function)
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
RoHS Status:
50.01MHz to 200.0MHz
3.3 VDC ±5%
LVCMOS
2.3ps typical, 4.0ps maximum
(for 155.250MHz)
4.0ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
See table below
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
See table
15pF
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
25mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
2 MW minimum
Monotonic and Positive. (An
increase of control voltage
always increases output
frequency.)
-50° to +100°C
±5ppm per year maximum
Pads 2 or 5, Enable high or 70%
Vdd min applied to Tri-state pad
to enable output.
30% Vdd max. to disable output
(high impedance)
Fully compliant
PHASE NOISE
Offset
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
Frequency 155.25MHz
-65dBc/Hz
-95dBc/Hz
-120dBc/Hz
-128dBc/Hz
-122dBc/Hz
-120dBc/Hz
-140dBc/Hz
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
PART NUMBER SCHEDULE
Example:
Supply Voltage
3 = +3.3V
Series Designator
GV64
Stability over temperature range
(See table)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
3GV64B-80N-155.25
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 Email: info@euroquartz.co.uk www.euroquartz.co.uk
28335 FLASH programming error
The error message is: gmake: *** No rule to make target `../F28335.cmd', needed by `ADCSAOPINFLASH.out'. There is no problem with the cmd file. Is there a problem with the program?...
caijianfa55 Microcontroller MCU
Share: How to estimate the temperature rise of surface mount semiconductors?
[align=left]Estimating the temperature rise of a semiconductor is simple. You simply calculate the power dissipation of the component and then use an electrical simulation of the cooling circuit to de...
error_echo Power technology
DAC output port simulation problem
When using Designer to simulate the IBIS model of DAC5672, when simulating the output port of the DAC, should a sinusoidal signal be added to the input port, and the output should be an analog signal,...
LiuQing Analogue and Mixed Signal
Why is there no connection icon after adding WIFI driver in WINCE6.0?
WINCE6.0 system, the development board is PXA310, the WIFI driver is also built-in, and the compilation is successful. The generated NK.nb0 is burned to the development board. Now the WIFI module is p...
wincezhang Embedded System
Impetuous emotions are destroying China's electronics industry!
"The boss of a local IC design company was called a 'liar' by people in the industry because the performance of its products did not match the publicity!" "The products of a local power IC design comp...
呱呱 MCU
About Ethernet
I have basically completed the data transmission using lwip, but there are still some problems. Please help me! 1. When I am transmitting a string of characters, the message "Failed to receive data" a...
lvfeihi Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 653  1850  2866  1425  1435  14  38  58  29  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号