Standard termination finish is 100% matte Tin (Sn).
Electrical Specifications
C0G (NP0)
Typical Capacitance Change vs. Temperature
15%
10%
5%
0%
-5%
-10%
-15%
-55˚C
-25˚C
0˚C
25˚C
50˚C
75˚C
100˚C
125˚C
Operating Temperature Range:
-55°C to +125°C
Temperature Coefficient:
0 ±30PPM/°C
Temperature Voltage Coefficient:
0 ±30PPM/°C
Insulation Resistance:
>100 Ω-F or 10 GΩ, whichever is less at 25°C, WDCV.
(The IR at 125°C is 10% of the value at 25°C)
Withstanding Voltage:
See below
Capacitance Tolerance:
C, D, F, G, J, K
Dielectric Strength is equal to 1.5 times rated voltage (WVDC) for 500 volt capacitors and 1.2 times (WVDC) for 1,000 through 5,000 volt capacitors.
Circuit applications in excess of 1,000 volts may require a surface coating to prevent external arcing.
Email:
sales@venkel.com
|
Phone:
512.794.0081
|
Toll Free:
800.950.8365
|
Web:
www.venkel.com
Rev.09/2014-F
1
High Voltage Ceramic Capacitors
(HVC Series)
Electrical Specifications
X7R
Typical Capacitance Change vs. Temperature
15%
10%
5%
0%
-5%
-10%
-15%
-55˚C
-25˚C
0˚C
25˚C
50˚C
75˚C
100˚C
125˚C
Operating Temperature Range:
-55°C to +125°C
Temperature Coefficient:
0 ±15%∆°C MAX.
Temperature Voltage Coefficient:
X7R not applicable
Insulation Resistance:
>100 ohms F or 10 G ohms, whichever
is less at 25°C, WDCV.
(The IR at 125°C is 10% of the value at 25°C)
Withstanding Voltage:
See below
D.F. Specification:
≥50V, ≤2.5%
Capacitance Tolerance:
J,K,M,N
Test Parameters
Test parameters for Multilayer Ceramic Capacitors - X7R:
Test parameters for Multilayer Ceramic Capacitors - C0G (NP0):
1KHz ± 50Hz at 1.0 ± 0.2 Vrms, 25°C
1MHz ± 50KHz at 1.0 ± 0.2 Vrms ≤ 1000pF, 25°C
1KHz ± 50Hz at 1.0 ± 0.2 Vrms > 1000pF, 25°C
Note:
To ensure proper capacitance readings, the voltage level must be held constant. The HP4284 and Agilent E4980 has a "ALC" (Automatic Level Control) function
and should be switched to the "ON" position for accurate capacitance readings.
Additional values may be available. Please contact us for more information. Due to demand and raw material fluctuations, specific values may not be available.
Additional values may be available. Please contact us for more information. Due to demand and raw material fluctuations, specific values may not be available.
Hello everyone, how to determine the stack size and task priority of a task, such as in nucleus, rex or threadX. I am a mobile phone developer, and I have never figured this out. Is it through experie...
Why does duty cycle change when moving up and down on an oscilloscope? Appendix Program #includeunsigned aa; void main(void) {WDTCTL = WDTPW + WDTHOLD; DCOCTL=0; BCSCTL1=CALBC1_1MHZ; DCOCTL=CALDCO_1MH...
When I was making CHIP-ON-LEAD products recently , I always got NSOP. Either the ball shape was not good or the line could not be hit . The machine I used was KNS. I hope you experts can give me some ...
Where are you planning to go during the May Day holiday? Leave a message and share the beautiful scenery you see!Source: WeChat official account: City of Craftsmanship
I have seen so many mountains, r...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
Editor's note: In order to help technicians or engineers who have knowledge of PIC microcontroller assembly language quickly master the method of using C language to program PIC microcontrollers, t...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
The TPS92210 is a single-stage LED lighting pulse width modulation (PWM) controller. The TRIAC dimmable solution not only regulates the LED current, but also achieves a power factor close to 1. The...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
Car lights, whether headlights, fog lights or tail lights, play an important role in driving safety. However, the material of the car lights determines that the probability of damage in a collision...[Details]