EEWORLDEEWORLDEEWORLD

Part Number

Search

475PLM035M

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 35V, 20% +Tol, 20% -Tol, 4.7uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size412KB,2 Pages
ManufacturerIllinois Capacitor
Websitehttp://www.illinoiscapacitor.com/
Environmental Compliance  
Download Datasheet Compare View All

475PLM035M Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 35V, 20% +Tol, 20% -Tol, 4.7uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT

PLM
FEATURES
+85°C 7mm Height
Low-Leakage Radial
Lead Aluminum
Electrolytic Capacitors
For all timing applications
I
Very small size
I
Capacitance range: 0.1 µF to 100 µF
SPECIFICATIONS
Capacitance Tolerance
Operating Temperature Range
Dissipation Factor
120Hz, 20°C
WVDC
tan
δ
WVDC
Impedance Ratio
(Max.) @120Hz
-25/20°C
-40/20°C
WVDC
Leakage Current
Time
6.3
.24
I
Voltage range: 6.3 WVDC to 50 WVDC
I
Solvent tolerant end seals standard
±20% at 120Hz, 20°C
-40°C to +85°C
10
.20
16
.16
25
.14
35
.12
50
.10
6.3
4
10
10
3
8
16
2
6
25
2
4
35
2
3
50
2
3
50 WVDC
2 minutes
.002CV or .4µA
whichever is greater
1,000 hours at 85°C with rated WVDC
Load Life
Capacitance change
Dissipation factor
Leakage current
< 20% of initial measured values
<200% of initial specified value
<Initial specified value
1,000 hours at 85°C with no voltage applied.
Units will meet load life specifications.
Shelf Life
Frequency (Hz)
Ripple Current Multipliers
50
0.8
120
1.0
400
1.3
1K
1.36
Temperature (°C)
10K
1.48
100K
1.53
+85
1.0
+70
1.3
+60
1.5
+45
1.8
SPECIAL ORDER OPTIONS
Special tolerances: ±10% (K), -10% + 30% (Q)
Epoxy end seal
Polyester sleeve
(See pages 33 thru 37)
Tape and Reel/Ammo Pack
Cut, formed, cut and formed, and snap-in leads
®
3757 W. Touhy Ave., Lincolnwood, IL 60712 • (847) 675-1760 • Fax (847) 673-2850 • www.illcap.com

475PLM035M Related Products

475PLM035M 335PLM050M 336PLM010M 336PLM025M 475PLM050M 476PLM016M 476PLM6R3M
Description Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 35V, 20% +Tol, 20% -Tol, 4.7uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT 85°C 7mm Height Low-Leakage Radial Lead Aluminum Electrolytic Capacitors 85°C 7mm Height Low-Leakage Radial Lead Aluminum Electrolytic Capacitors 85°C 7mm Height Low-Leakage Radial Lead Aluminum Electrolytic Capacitors 85°C 7mm Height Low-Leakage Radial Lead Aluminum Electrolytic Capacitors 85°C 7mm Height Low-Leakage Radial Lead Aluminum Electrolytic Capacitors 85°C 7mm Height Low-Leakage Radial Lead Aluminum Electrolytic Capacitors
How can I make the keyboard filter driver (ctrl2cap) serve only my application? ? ?
For example, when my application is active, pressing the F12 key is equivalent to pressing the F1 key, while other programs in the system run normally (F12 is still F12). When my user program calls De...
上下游的鱼 Embedded System
The Altium+Access library for personal use is now shared for free
[i=s]This post was last edited by MrKingMCU on 2017-11-17 21:36[/i] I have written a similar post before, the link is as follows: Altium+Access DIY to create a small company's own library [url=https:/...
MrKingMCU PCB Design
Error displayed when generating wince with VS2005~~~
The compilation passed, but when it came to ATTACH DEVICE, there was a problem with the wince interface generated. The wince screen appeared, but the standard tool could not display the following scre...
fiercewind Embedded System
OK6410 u-boot transplantation failed, u-boot was successfully generated, but could not be started in the SD card
RT 1. Operating environment Development board: OK6410 VMware: 10.0.2 Linux: Ubuntu14.04LTS U-boot: u-boot-2010.03.tar.bz2 2. Situation description According to this tutorial [url]http://www.linuxidc.c...
youwei_ai ARM Technology
STM32F407 transmission problem about i2s DMA
Recently, I used stm32f407 to make a project of audio transmission after decoding mp3 from sd card. The sound card chip used was VM8978, i2s of SPI3 was adopted, and the DMA used was stream5 channel 0...
xslyk stm32/stm8
How to deal with the inductor spike at the back end of the switching power supply
I just entered the power supply circle. During my internship, I did push-pull. I boosted 18~36V to 450V for stabilization. I added an inductor at the back end, but the spike was very large. I added an...
helloxx Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 694  2771  836  751  740  14  56  17  16  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号