EEWORLDEEWORLDEEWORLD

Part Number

Search

GMSM6-20P-6C4-2.000B

Description
D Microminiature Connector, 20 Contact(s), Male, Solder Terminal, Plug
CategoryThe connector    The connector   
File Size321KB,3 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

GMSM6-20P-6C4-2.000B Overview

D Microminiature Connector, 20 Contact(s), Male, Solder Terminal, Plug

GMSM6-20P-6C4-2.000B Parametric

Parameter NameAttribute value
MakerGlenair
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresLOW PROFILE
Body/casing typePLUG
Connector typeD MICROMINIATURE CONNECTOR
Contact to complete cooperationGOLD
Contact completed and terminatedGOLD
Contact point genderMALE
DIN complianceNO
empty shellNO
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceNO
Manufacturer's serial numberGMSM
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation typeCABLE
OptionsGENERAL PURPOSE
Shell materialALUMINUM ALLOY
Termination typeSOLDER
Total number of contacts20
Micro-D
Single Row
Solder Cup and Pre-Wired Connectors
GMSM Connectors
offer mil spec design and performance in a
smaller form factor. These GMSM single row connectors are
reduced in height compared to two-row Micro-D connectors.
GMSM Connectors
feature gold plated TwistPin contacts, machined
aluminum shells, and are fully potted with epoxy. Choose
from 4 to 35 contacts. Available in a variety of finishes, socket
connectors are fitted with Fluorosilicone interfacial seals.
GMSM Low Profile Single Row
Metal Shell Microminiature
HOW TO ORDER GMSM SOLDER CUP CONNECTORS
D
Series
GMSM
1
2
4
5
6
Shell Finish
– Cadmium
– Nickel
– Black Anodize
– Gold
– Chem Film
Number of
Contacts
4
6
10
15
20
25
30
35
Contact
Type
P
– Pin
S
– Socket
Termination
Type
S
Solder Cup
Hardware
B
P
M
M1
S
S1
L
K
F
R
Solder Cup
Stainless Steel Shell
3
– Passivated
Sample Part Number
GMSM
1 –
15
P
S
B
MICRO-D MOUNTING HARDWARE
B
P
M
M1
S
S1
L
K
F
R
Thru-Hole Jackpost Jackscrew Jackscrew Jackscrew Jackscrew Jackscrew Jackscrew Float Mount Float Mount
Order
Hardware
Separately
Removable
Includes Nut
and Washer
Hex Head
Removable
E-ring
Hex Head
Removable
E-ring
Extended
Slot Head
Removable
E-ring
Slot Head
Removable
E-ring
Extended
Hex Head
Non-
Removable
Slot Head
Non-
Removable
Extended
For Front
Panel
Mounting
For Rear
Panel
Mounting
© 2011 Glenair, Inc.
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
E-Mail: sales@glenair.com
D-2
RC passive filter circuit and its principle
[b] In the test system, RC filter is often used. Because in this field, the signal frequency is relatively low. The RC filter circuit is simple, has strong anti-interference, has good low-frequency pe...
qwqwqw2088 Analogue and Mixed Signal
ADS8332 Question 2: Where does this interference come from?
I used C2000's SPI to drive ADS8332. I've had success in the past, but it was on a different PCB. However, when I tried it again, I ran into a lot of problems. [/font] Phenomenon: When the sampling an...
dontium Analogue and Mixed Signal
I would like to ask about the timer interrupt problem (I have been unable to find any information, please give me some advice)
Question 1: Is it necessary to install the initial value of the timer in the main function? I seem to have tried it and it works fine without it. Question 2: If timer 0 is turned off in timer 1, do I ...
唐菲远 51mcu
How to implement the 20-bit address pointer of MSP430FG461X series in C language?
When I assign a 20-bit address 0x10000 to a pointer variable, it always says that it is out of the range of 0 to 0xFFFF.This is possible in assembly language, because MSP430X provides instructions wit...
我爱电子 Microcontroller MCU
Crystal oscillator problem
Please help me analyze this:the crystal oscillator is not working properly. It does not oscillate at first. Then I touch it with a soldering iron and it works normally for a while. Then it does not os...
chenzep Microcontroller MCU
Regarding the issue of running programs under pure DOS on the PC104 device, is there any difference between the pure DOS booted by the virtual floppy drive and the actually installed DOS?
As the title says. Now the program runs in pure DOS booted by virtual floppy drive. The program written in 2000 with bc31 runs smoothly in 2000, but it is very stuck in DOS. I want to compile it in DO...
lionedwolf Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1356  106  355  1802  1099  28  3  8  37  23 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号