EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-FI2SC436N

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-FI2SC436N Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), SC/UPC Connector,

PH1-FI2SC436N Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknow
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsGR-253
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1564 nm
Nominal optical power output1.122 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
(The problem has been solved) Ask Vivi's load flash Vivi x problem
I found a clean vivi, transplanted it, put jtag on the development board, and then connected it with dnw.exe. After entering the vivishell, I used bon part 0 192k 1216k partition. After completion, I ...
spirit_only Embedded System
NXP Technology Center has been revamped. Do you like this interface?
[font=微软雅黑][size=5]>>[url=https://www.eeworld.com.cn/zhuanti/eewNXPminisite/]NXP Technology Center[/url] has been redesigned! ! ! Do you like this interface? [/size][/font]:victory:...
EEWORLD社区 NXP MCU
Registry configuration when making a CAB installer for wince.
Everyone knows that the Windows directory of wince cannot save files when the power is off. When installing the WINCE driver, the relevant registry contains the DLL file name. If we do not put the DLL...
wangyg007 Embedded System
Ask the analog electronics expert about the power amplifier circuit
The amplifier uses TDA2030, and the circuit uses the standard application given by DATASHEET (Figure 1). I calculated it and it worked, but there was no output after it was actually built. I built hal...
fighting Analog electronics
NEC develops small, inexpensive observation satellite
[p=21, 2, left][font=Tahoma,][color=rgb(51, 51, 51)][font=Verdana, Helvetica, Arial, sans-serif][font=宋体][b]NEC[/b]和無碼宇宙航空研究开发机构([/font][font=Times New Roman]JAXA[/font][font=宋体])联手开发出低价位小型观测[b][u]卫星[...
egsales016 Automotive Electronics
How to check the accuracy of op amp and ADC?
I am a novice. I want to design a high-precision weighing system. The accuracy of the weighing sensor is 1/10000 (0.01%), that is, the measuring range of 10kg can distinguish 1g. The output voltage of...
wyzbict Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1177  2194  1742  347  954  24  45  36  7  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号