regulator. It features 45μA quiescent current, dropping
to 10μA in shutdown. A new reference amplifier topology
gives precision DC characteristics along with the ability to
maintain good loop stability with an extremely wide range
of output capacitors. Very low dropout voltage and high
efficiency are obtained with a unique power transistor
anti-saturation design. Adjustable and fixed 5V versions
are available.
Several new features make the LT1175 very user-friendly.
The
SHDN
pin can interface directly to either positive or
negative logic levels. Current limit is user-selectable at
200mA, 400mA, 600mA and 800mA. The output can be
forced to reverse voltage without damage or latchup. Un-
like some earlier designs, the increase in quiescent current
during a dropout condition is actively limited.
The LT1175 has complete blowout protection with current
limiting, power limiting and thermal shutdown. Special
attention was given to the problem of high temperature
operation with micropower operating currents, preventing
output voltage rise under no-load conditions. The LT1175
is available in 8-pin PDIP and SO packages, 3-lead SOT-
223 as well as 5-pin surface mount DD and through-hole
TO-220 packages. The 8-pin SO package is specially
constructed for low thermal resistance.
Operating Current: 45μA
Adjustable Current Limit
Low Voltage Linear Dropout Characteristics
Stable with Wide Range of Output Capacitors
Shutdown Current: 10μA
Positive or Negative Shutdown Logic
Fixed 5V and Adjustable Versions
Tolerates Reverse Output Voltage
Available in 8-pin PDIP and SO Packages, 3-lead
SOT-223, 5-Pin Surface Mount DD and Through-Hole
TO-220 Packages
APPLICATIONS
n
n
n
n
n
n
Analog Systems
Modems
Instrumentation
A/D and D/A Converters
Interface Drivers
Battery-Powered Systems
L,
LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
TYPICAL APPLICATION
1.0
Minimum Input-to-Output Voltage
T
J
= 25°C
I
LIM2
, I
LIM4
TIED TO V
IN
0.8
Typical LT1175 Connection
+
C
IN
*
–V
IN
V
IN
I
LIM2
I
LIM4
LT1175-5
OUTPUT
SHDN
GND
SENSE
+
C
OUT
≥ 0.1μF
–5V
UP TO 500mA
INPUT-TO-OUTPUT VOLTAGE (V)
0.6
0.4
0.2
*C
IN
IS NEEDED ONLY IF REGULATOR IS MORE THAN 6" FROM
INPUT SUPPLY CAPACITOR. SEE APPLICATIONS INFORMATION
1175 TA01
SECTION FOR DETAILS
0
0
0.1
0.2 0.3 0.4
0.5
OUTPUT CURRENT (A)
0.6
0.7
1175 TA02
1175ff
1
LT1175
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Input Voltage (Transient 1 sec, Note 12) ...................25V
Input Voltage (Continuous) .......................................20V
Input-to-Output Differential Voltage (Note 13) ..........20V
5V SENSE Pin (with Respect to GND Pin) ......... 2V, –10V
ADJ SENSE Pin
(with Respect to OUTPUT Pin)...................20V, –0.5V
5V SENSE Pin
(with Respect to OUTPUT Pin)......................20V, –7V
Output Reverse Voltage ..............................................2V
SHDN
Pin to GND Pin Voltage (Note 3) ........ 13.5V, –20V
SHDN
Pin to V
IN
Pin Voltage .............................30V, –5V
Operating Junction Temperature Range (Note 2)
LT1175C ................................................. 0°C to 125°C
LT1175I .............................................. –40°C to 125°C
LT1175MP .......................................... –55°C to 125°C
Storage Temperature Range .................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec)................... 300°C
PIN CONFIGURATION
TOP VIEW
V
IN
1
I
LIM2
2
OUTPUT 3
SENSE 4
8
7
6
5
V
IN
I
LIM4
SHDN
GND
TAB
IS
V
IN
FRONT VIEW
5
4
3
2
1
SHDN
GND
V
IN
SENSE
OUTPUT
FRONT VIEW
3
TAB IS
V
IN
2
1
GND
V
IN
OUTPUT
N8 PACKAGE
8-LEAD PDIP
θ
JA
= 80°C/W TO 120°C/W
DEPENDING ON PC BOARD LAYOUT
TOP VIEW
V
IN
1
I
LIM2
2
OUTPUT 3
SENSE 4
8
7
6
5
V
IN
I
LIM4
SHDN
GND
Q PACKAGE
5-LEAD PLASTIC DD-PAK
θ
JA
= 27°C/W TO 60°C/W
DEPENDING ON PC MOUNTING.
SEE DATA SHEET FOR DETAILS
ST PACKAGE
3-LEAD PLASTIC SOT-223
θ
JA
= 50°C/W
WITH BACKPLANE AND 10cm
2
TOPSIDE LAND SOLDERED TO TAB
FRONT VIEW
5
4
3
2
1
TAB IS
V
IN
SHDN
GND
V
IN
SENSE
OUTPUT
S8 PACKAGE
8-LEAD PLASTIC SO
θ
JA
= 60°C/W TO 100°C/W
DEPENDING ON PC BOARD LAYOUT
PINS 1, 8 ARE INTERNALLY CONNECTED TO DIE ATTACH PADDLE FOR HEAT SINKING.
ELECTRICAL CONTACT CAN BE MADE TO EITHER PIN. FOR BEST THERMAL RESISTANCE,
PINS 1, 8 SHOULD BE CONNECTED TO AN EXPANDED LAND THAT IS OVER AN INTERNAL
OR BACKSIDE PLANE.
SEE APPLICATIONS INFORMATION
T PACKAGE
5-LEAD PLASTIC TO-220
θ
JA
= 50°C/W,
θ
JC
= 5°C/W
1175ff
2
LT1175
ORDER INFORMATION
LEAD FREE FINISH
LT1175CN8#PBF
LT1175CN8-5#PBF
LT1175CS8#PBF
LT1175CS8-5#PBF
LT1175CST-5#PBF
LT1175CQ#PBF
LT1175CQ-5#PBF
LT1175CT#PBF
LT1175CT-5#PBF
LT1175IN8#PBF
LT1175IN8-5#PBF
LT1175IS8#PBF
LT1175IS8-5#PBF
LT1175IST-5#PBF
LT1175IQ#PBF
LT1175IQ-5#PBF
LT1175IT#PBF
LT1175IT-5#PBF
LT1175MPS8#PBF
LT1175MPS8-5#PBF
LT1175MPQ#PBF
LT1175MPQ-5#PBF
LEAD BASED FINISH
LT1175CN8
LT1175CN8-5
LT1175CS8
LT1175CS8-5
LT1175CST-5
LT1175CQ
LT1175CQ-5
LT1175CT
LT1175CT-5
LT1175IN8
LT1175IN8-5
LT1175IS8
LT1175IS8-5
LT1175IST-5
LT1175IQ
LT1175IQ-5
TAPE AND REEL
LT1175CN8#TRPBF
LT1175CN8-5#TRPBF
LT1175CS8#TRPBF
LT1175CS8-5#TRPBF
LT1175CST-5#TRPBF
LT1175CQ#TRPBF
LT1175CQ-5#TRPBF
LT1175CT#TRPBF
LT1175CT-5#TRPBF
LT1175IN8#TRPBF
LT1175IN8-5#TRPBF
LT1175IS8#TRPBF
LT1175IS8-5#TRPBF
LT1175IST-5#TRPBF
LT1175IQ#TRPBF
LT1175IQ-5#TRPBF
LT1175IT#TRPBF
LT1175IT-5#TRPBF
LT1175MPS8#TRPBF
LT1175MPS8-5#TRPBF
LT1175MPQ#TRPBF
LT1175MPQ-5#TRPBF
TAPE AND REEL
LT1175CN8#TR
LT1175CN8-5#TR
LT1175CS8#TR
LT1175CS8-5#TR
LT1175CST-5#TR
LT1175CQ#TR
LT1175CQ-5#TR
LT1175CT#TR
LT1175CT-5#TR
LT1175IN8#TR
LT1175IN8-5#TR
LT1175IS8#TR
LT1175IS8-5#TR
LT1175IST-5#TR
LT1175IQ#TR
LT1175IQ-5#TR
PART MARKING*
LT1175CN8
LT1175CN8-5
1175
11755
11755
LT1175CQ
LT1175CQ-5
LT1175CT
LT1175CT-5
LT1175IN8
LT1175IN8-5
1175I
1175I5
1175I5
LT1175IQ
LT1175IQ-5
LT1175IT
LT1175IT-5
1175MP
175MP5
LT1175MPQ
LT1175MPQ-5
PART MARKING*
LT1175CN8
LT1175CN8-5
1175
11755
11755
LT1175CQ
LT1175CQ-5
LT1175CT
LT1175CT-5
LT1175IN8
LT1175IN8-5
1175I
1175I5
1175I5
LT1175IQ
LT1175IQ-5
PACKAGE DESCRIPTION
8-Lead Plastic Dip
8-Lead Plastic Dip
8-Lead Plastic SO
8-Lead Plastic SO
3-Lead Plastic SOT-223
5-Lead Plastic DD-Pak
5-Lead Plastic DD-Pak
5-Lead Plastic TO-220
5-Lead Plastic TO-220
8-Lead Plastic Dip
8-Lead Plastic Dip
8-Lead Plastic SO
8-Lead Plastic SO
3-Lead Plastic SOT-223
5-Lead Plastic DD-Pak
5-Lead Plastic DD-Pak
5-Lead Plastic TO-220
5-Lead Plastic TO-220
8-Lead Plastic SO
8-Lead Plastic SO
5-Lead Plastic DD-Pak
5-Lead Plastic DD-Pak
PACKAGE DESCRIPTION
8-Lead Plastic Dip
8-Lead Plastic Dip
8-Lead Plastic SO
8-Lead Plastic SO
3-Lead Plastic SOT-223
5-Lead Plastic DD-Pak
5-Lead Plastic DD-Pak
5-Lead Plastic TO-220
5-Lead Plastic TO-220
8-Lead Plastic Dip
8-Lead Plastic Dip
8-Lead Plastic SO
8-Lead Plastic SO
3-Lead Plastic SOT-223
5-Lead Plastic DD-Pak
5-Lead Plastic DD-Pak
TEMPERATURE RANGE
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–55°C to 125°C
–55°C to 125°C
–55°C to 125°C
–55°C to 125°C
TEMPERATURE RANGE
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
1175ff
3
LT1175
ORDER INFORMATION
LEAD FREE FINISH
LT1175IT
LT1175IT-5
LT1175MPS8
LT1175MPS8-5
LT1175MPQ
LT1175MPQ-5
TAPE AND REEL
LT1175IT#TR
LT1175IT-5#TR
LT1175MPS8#TR
LT1175MPS8-5#TR
LT1175MPQ#TR
LT1175MPQ-5#TR
PART MARKING*
LT1175IT
LT1175IT-5
1175MP
175MP5
LT1175MPQ
LT1175MPQ-5
PACKAGE DESCRIPTION
5-Lead Plastic TO-220
5-Lead Plastic TO-220
8-Lead Plastic SO
8-Lead Plastic SO
5-Lead Plastic DD-Pak
5-Lead Plastic DD-Pak
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–55°C to 125°C
–55°C to 125°C
–55°C to 125°C
–55°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
ELECTRICAL CHARACTERISTICS
PARAMETER
Feedback Sense Voltage
Output Voltage Initial Accuracy
Output Voltage Accuracy (All Conditions)
Quiescent Input Supply Current
GND Pin Current Increase with Load (Note 5)
Input Supply Current in Shutdown
Shutdown Thresholds (Note 10)
SHDN
Pin Current (Note 3)
Output Bleed Current in Shutdown (Note 7)
SENSE Pin Input Current
Dropout Voltage (Note 8)
The
l
denotes specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
OUT
= 5V, V
IN
= 7V, I
OUT
= 0, V
SHDN
= 3V, I
LIM2
and I
LIM4
tied to V
IN
.
To avoid confusion with “min” and “max” as applied to negative voltages, all voltages are shown as absolute values except where
polarity is not obvious.
CONDITIONS
Adjustable Part
Fixed 5V Part
Adjustable, Measured at 3.8V Sense
Fixed 5V
V
IN
– V
OUT
= 1V to V
IN
= 20V, I
OUT
= 0A to 500mA
P = 0 to P
MAX
, T
J
= T
MIN
to T
MAX
(Note 4)
V
IN
– V
OUT
≤ 12V
l
MIN
3.743
4.93
TYP
3.8
5.0
0.5
0.5
1.5
45
10
10
MAX
3.857
5.075
1.5
1.5
2.5
65
80
20
20
25
2.5
2.6
UNITS
V
V
%
%
%
μA
μA
μA/mA
μA
μA
V
V
μA
μA
μA
μA
nA
μA
V
V
V
V
V
V
l
l
V
SHDN
= 0V
Either Polarity On
SHDN
Pin (C-, I-Grades)
Either Polarity On
SHDN
Pin (MP-Grade)
V
SHDN
= 0V to 10V (Flows Into Pin)
V
SHDN
= –15V to 0V (Flows Into Pin)
V
OUT
= 0V, V
IN
= 15V
(Adjustable Part Only, Current Flows Out of Pin)
(Fixed Voltage Only, Current Flows Out of Pin)
I
OUT
= 25mA
I
OUT
= 100mA
I
OUT
= 500mA
I
LIM2
Open, I
OUT
= 300mA
I
LIM4
Open, I
OUT
= 200mA
I
LIM2
, I
LIM4
Open, I
OUT
= 100mA
l
l
l
l
0.8
0.8
4
1
0.1
1
75
12
0.1
0.18
0.5
0.33
0.3
0.26
8
4
1
5
150
20
0.2
0.26
0.7
0.5
0.45
0.45
l
l
l
l
l
l
l
l
l
1175ff
4
LT1175
ELECTRICAL CHARACTERISTICS
PARAMETER
Current Limit (Note 12)
The
l
denotes specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
OUT
= 5V, V
IN
= 7V, I
OUT
= 0, V
SHDN
= 3V, I
LIM2
and I
LIM4
tied to V
IN
.
To avoid confusion with “min” and “max” as applied to negative voltages, all voltages are shown as absolute values except where
polarity is not obvious.
CONDITIONS
V
IN
– V
OUT
= 1V to 12V
I
LIM2
Open
I
LIM4
Open
I
LIM2
, I
LIM4
Open
V
IN
– V
OUT
= 1V to V
IN
= 20V
I
OUT
= 0mA to 500mA
P = 0 to P
MAX
(Notes 4, 9)
T
J
= 25°C to T
JMIN
, or 25°C to T
JMAX
5-Pin Packages
8-Pin Packages
l
l
l
l
l
l
MIN
520
390
260
130
TYP
800
600
400
200
0.003
0.1
0.04
0.1
0.25
MAX
1300
975
650
325
0.015
0.35
0.1
0.2
1.25
UNITS
mA
mA
mA
mA
%/V
%
%/W
%/W
%
Line Regulation (Note 11)
Load Regulation (Note 6, 11)
Thermal Regulation
Output Voltage Temperature Drift
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LT1175 regulators are tested and specified under pulse load
conditions such that T
J
T
A
. The LT1175C is 100% production tested
at T
A
= 25°C. Performance at 0°C and 125°C is assured by design,
characterization and correlation with statistical process controls. The
LT1175I is guaranteed over the full –40°C to 125°C operating junction
temperature range. The LT1175MP is 100% tested and guaranteed over
the –55°C to 125°C operating junction temperature range.
Note 3:
SHDN
pin maximum positive voltage is 30V with respect to
– V
IN
and 13.5V with respect to GND. Maximum negative voltage is –20V
with respect to GND and –5V with respect to –V
IN
.
Note 4:
P
MAX
= 1.5W for 8-pin packages, and 6W for 5-pin packages.
This power level holds only for input-to-output voltages up to 12V, beyond
which internal power limiting may reduce power. See Guaranteed Current
Limit curve in Typical Performance Characteristics section. Note that all
conditions must be met.
Note 5:
GND pin current increases because of power transistor base
drive. At low input-to-output voltages (<1V) where the power transistor
is in saturation, GND pin current will be slightly higher. See Typical
Performance Characteristics.
Note 6:
With I
LOAD
= 0, at T
J
> 125°C, power transistor leakage could
increase higher than the 10μA to 25μA drawn by the output divider or fixed
voltage SENSE pin, causing the output to rise above the regulated value.
To prevent this condition, an internal active pull-up will automatically turn
on, but supply current will increase.
Note 7:
This is the current required to pull the output voltage to within 1V
of ground during shutdown.
Note 8:
Dropout voltage is measured by setting the input voltage equal to
the normal regulated output voltage and measuring the difference between
V
IN
and V
OUT
. For currents between 100mA and 500mA, with both I
LIM
pins tied to V
IN
, maximum dropout can be calculated from
V
DO
= 0.15 + 1.1Ω (I
OUT
).
Note 9:
Thermal regulation is a change in the output voltage caused by
die temperature gradients, so it is proportional to chip power dissipation.
Temperature gradients reach final value in less than 100ms. Output voltage
changes after 100ms are due to absolute die temperature changes and
reference voltage temperature coefficient.
Note 10:
The lower limit of 0.8V is guaranteed to keep the regulator in
shutdown. The upper limit of 2.5V is guaranteed to keep the regulator
active. Either polarity may be used, referenced to GND pin.
Note 11:
Load and line regulation are measured on a pulse basis with
pulse width of 20ms or less to keep chip temperature constant. DC
regulation will be affected by thermal regulation (Note 8) and chip
temperature changes. Load regulation specification also holds for currents
up to the specified current limit when I
LIM2
or I
LIM4
are left open.
Note 12:
Current limit is reduced for input-to-output voltage above 12V.
See the graph in Typical Performance Characteristics for guaranteed limits
above 12V.
Note 13:
Operating at very large input-to-output differential voltages
(>15V) with load currents less than 5mA requires an output capacitor with
an ESR greater than 1Ω to prevent low level output oscillations.
The compiler is winavr2010 ucos version 2.85 for mega128 protus 7 professional creates two tasks, task 1 requests the semaphore to make PORTA level high, delay and then release the semaphore, task 2 r...
[font=Tahoma, Helvetica, SimSun, sans-serif]After running MicroPython on NodeMCU a few days ago, I successfully ran MicroPython on the Xiaoe development board today. After flashing the firmware, I can...
I am new to using the msp430 launchpad. Because it has few io ports, I bought an oled, but I can't drive it anyway. I am very distressed: Sad:. Now I post the program for everyone to see. Please tell ...
As shown in the picture, the IC is TI's TPS61040, a backlight boost IC. What is the effect of the inductor on the entire drive circuit? Is there a calculation formula for selection? And the capacity o...
If you have relevant information, please send it to [url=mailto:554145080@qq.com]554145080@qq.com[/url], thank you very much! ! ! Urgently needed! ! ! [[i] This post was last edited by sunxy9562 on 20...
1. Equipment Overview
Shell-and-tube heat exchangers are a common heat exchange device used in chemical evaporation and heating equipment. Currently, the tubesheets of shell-and-tube heat exch...[Details]
Most of the houses we live in now are elevator buildings, mainly because it is more convenient to go up and down the stairs! It can also make life more comfortable. It even helps to increase the ad...[Details]
1. Project Overview
1.1 Introduction
Currently, most music files are saved in MP3 format, a lossy audio compression format that cannot perfectly reproduce the original music. With the exp...[Details]
Robotics
has become
LiDAR
's "second growth curve."
While LiDAR was still battling with its "pure vision" rivals in the automotive field, another field ignited the demand f...[Details]
The all-new MG4 was recently officially announced on the Ministry of Industry and Information Technology's (MIIT) new vehicle announcement. The all-new MG4's semi-solid-state battery version addres...[Details]
On August 22, according to the Ministry of Industry and Information Technology's official website, my country's first mandatory national standard for the control of hazardous substances in electric...[Details]
1 Source of creativity
With the further development of electronic technology, electronic pets have gradually entered people's family life. At present, there are two main categories of relative...[Details]
Since its invention in the mid-1940s, the microwave oven has evolved from a humble beginning to commercial use, entering homes in the 1960s and rapidly gaining popularity. Its basic functionality a...[Details]
In June 2014, the Ministry of Industry and Information Technology issued 4G FD-LTE licenses to China Unicom and China Telecom. Together with the 4G TD-LTE licenses issued to China Mobile, China Uni...[Details]
With the development of science, the use of variable frequency technology is becoming more and more widespread, and it is used in both industrial equipment and household appliances. Inverter air co...[Details]
There are basically three causes of spontaneous combustion of electric vehicles: The first is that the battery components are punctured or suffer fatal damage due to a collision accident, and part ...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
Keysight Technologies is combining its electromagnetic simulator with Synopsys' AI-driven RF design migration flow to create an integrated design flow for migrating from TSMC's N6RF+ process techno...[Details]
Plessey Semiconductors has been acquired by Haylo Labs, which was established in March last year with a $100 million, five-year loan from Chinese technology company Goertek.
Haylo Labs w...[Details]
On August 21st, BYD announced the launch of its next-generation "Little White Pile" product, the "Lingchong"
charging
pile
, which is now available for general sale. This charging pile feat...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
