EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-116-30-1300RLF

Description
Board Connector, 60 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54122-116-30-1300RLF Overview

Board Connector, 60 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle

54122-116-30-1300RLF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompli
body width0.19 inch
subject depth0.512 inch
body length3 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrie
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number54122
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts60
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
Problems encountered in programming F2812
I want to transplant ucos to 2812, but encountered some problems during burning. I have seen this problem in the forum, but I am not sure how to solve it specifically.The following is the situation en...
zlhjd Microcontroller MCU
How to collect negative voltage output of eddy current displacement sensor
The data acquisition instrument originally had two channels with acceleration sensors. I bought an eddy current displacement sensor some time ago. I want to use one instrument to collect acceleration ...
xyer Analog electronics
My CY7C68013 cannot be recognized when powered on, why?
The reset circuit is 100k, 1uf, SDL and SDA are all pulled up, what could be the problem?...
huj Embedded System
Xintang: Secure In-System-Programming protects firmware burning security
In system programming (ISP) provides a convenient way to update firmware on a complete product. Even on a brand new product without any firmware installed, ISP can be used to install the initial firmw...
火辣西米秀 Domestic Chip Exchange
Contactless Smart Card Introduction
Contactless CPU card and logic encryption card 1. Logic encryption memory card: Based on the non-encrypted memory card, an encryption logic circuit is added. The encryption logic circuit protects the ...
zhangzzmts RF/Wirelessly
Power module design
[i=s] This post was last edited by dql2016 on 2017-3-29 17:10 [/i]This is a power module designed before, using TI's DC-DC chip TPS56628, the parameters are as follows:Maximum current of 6A, very powe...
dql2016 MEMS sensors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 15  62  668  434  2220  1  2  14  9  45 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号