EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-410-57-2150

Description
Board Connector, 114 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle,
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54122-410-57-2150 Overview

Board Connector, 114 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle,

54122-410-57-2150 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid306135098
Reach Compliance Codecompliant
Country Of OriginFrance
ECCN codeEAR99
YTEOL9.1
body width0.19 inch
subject depth0.846 inch
body length5.7 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialPOLYETHYLENE
JESD-609 codee0
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness79u inch
Rated current (signal)3 A
GuidelineUL, CSA
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts114
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
How to determine the end of ADC and what impact does the ADC conversion cycle have on accuracy?
1. My program uses DMA1 for transmission. How do I determine the end of ADC?Should I determine it inthe void DMA1_Channel1_IRQHandler(void){}function?How should I do it?2. What is the impact of ADC co...
lingr stm32/stm8
【allegro】The routing between two components is not correct
As shown in the picture:Why can't the line be pushed straight in this place? ? Help, help~~...
ohahaha PCB Design
I found a document about A/D noise performance. Please read it (2)
[b]Use noise dithering to improve the spurious-free dynamic range of the ADC[/b] Spurious-free dynamic range (SFDR) is the ratio of the RMS signal amplitude to the RMS value of the largest spurious sp...
linda_xia Analog electronics
Regarding "Circuit Design Based on Operational Amplifiers and Analog Integrated Circuits", there is a concept of "Pole" that is not clear
[i=s]This post was last edited by sunboy25 on 2020-10-8 23:15[/i]I would like to ask, is the place where I drew the red circle in the picture above correct as described in the book? Why do I feel that...
sunboy25 Analog electronics
RISC-V IDE MRS usage notes (Part 3): Improving floating-point calculation efficiency
MRS has built-in CH32V30X series chips. This series of chips supports FPU (floating point unit). If you want to turn it on, you need to enable the corresponding extension, as shown in the figure below...
Moiiiiilter MCU
Pan it STM32H750 3 (lan8720 Ethernet test --iperf)
[font=宋体][size=4] When debugging lan8720 hardware, you need to check whether the ground pad is cold soldered, whether the internal voltage regulator 1.2V has output, and whether it has output 50M freq...
RCSN stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 10  2260  424  1082  1054  1  46  9  22  11 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号